With the new improvements in the fuel economy engines and to enhance the passenger’s comfort, the topic of active vibration cancellation has received a lot of attention recently by both the automotive industry and researchers. Engine mounts and bushings are the devices used to suppress the transverse and tensional vibrations of engines, respectively. Engine mounts and bushings are primarily designed for the first order vibration of engine. Higher order vibrations, however, are neglected due to their lower amplitudes. Although lots of research has been focused on the improvement of the design and performance of engine mounts, engine bushings has not been addressed well in the literature. This paper focuses on the modeling and design of an active bushing, which addresses the higher order vibrations in engines. Such a bushing has a significant advantage in the ride quality of the newly commercialized variable displacement engine (VDE), where the amplitude of vibration induced by switching is higher than normal engines. For VDEs the higher amplitude of vibration makes the higher orders sensible. Isolation of these vibrations is beyond the capabilities of the passive hydraulic bushings. In this paper the design of a novel active chamber is proposed, which is ultimately utilized to control the fluid pressure inside the bushing. It is evident that the fluid pressure significantly contributes to the dynamic performance of the hydraulic bushing. The active chamber described in this paper utilizes a magnetic actuator, excited by electrical current signal, which is fed to a solenoid coil. The pulses produced by the magnetic actuator are used to adjust the pressure at any specific frequency. This feature enables the active chamber not only to alter the frequency response characteristic of the hydraulic bushing, but also to generate complex pressure frequency responses. A mathematical linear model for the magnetic actuator, and the active bushing assembly, is provided and then verified experimentally. The experimental results confirm that the active hydraulic bushing can well address the sophisticated vibration isolation requirements particular to the VDE systems.
Skip Nav Destination
e-mail: mfgolnar@sfu.ca
Article navigation
August 2010
Research Papers
Development of an Active Compliance Chamber to Enhance the Performance of Hydraulic Bushings
M. F. Golnaraghi
M. F. Golnaraghi
Professor
Department of Mechatronic Systems Engineering, Burnaby Mountain Chair, School of Engineering Science,
e-mail: mfgolnar@sfu.ca
Simon Fraser University
, Surrey, BC, V3T 0A3, Canada
Search for other works by this author on:
S. Arzanpour
Assistant Professor
M. F. Golnaraghi
Professor
Department of Mechatronic Systems Engineering, Burnaby Mountain Chair, School of Engineering Science,
Simon Fraser University
, Surrey, BC, V3T 0A3, Canadae-mail: mfgolnar@sfu.ca
J. Vib. Acoust. Aug 2010, 132(4): 041012 (7 pages)
Published Online: July 15, 2010
Article history
Received:
April 11, 2009
Revised:
March 23, 2010
Online:
July 15, 2010
Published:
July 15, 2010
Citation
Arzanpour, S., and Golnaraghi, M. F. (July 15, 2010). "Development of an Active Compliance Chamber to Enhance the Performance of Hydraulic Bushings." ASME. J. Vib. Acoust. August 2010; 132(4): 041012. https://doi.org/10.1115/1.4001500
Download citation file:
Get Email Alerts
Cited By
Boundary-Element Analysis of the Noise Scattering for Urban Aerial Mobility Vehicles: Solver Development and Assessment
J. Vib. Acoust (October 2024)
Related Articles
Three-Dimensional Heat Transfer Analysis of Pin-Bushing System With Oscillatory Motion: Theory and Experiment
J. Tribol (January,2011)
Tribo-Informatics Approach to Investigate the Friction and Wear of Bushings in the Variable Stator Vane System
J. Tribol (December,2023)
Lubricated Hybrid Journal Bearings
J. Tribol (July,2011)
Application of Cyclo-Nonstationary Indicators for Bearing Monitoring Under Varying Operating Conditions
J. Eng. Gas Turbines Power (January,2018)
Related Proceedings Papers
Related Chapters
Performance Analysis of Rear Rubber Bushing Stiffness of Lower Control Arm on McPherson Suspension
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
The Electric Field Analysis of Power Transformer Bushing
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)
The Analysis of Engine Vibration Signals Based on Wavelet Packet
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3