Several years ago an effort was undertaken at MIT to develop high-speed rotating MEMS (Micro Electro-Mechanical Systems) using computer chip fabrication technology. To enable high-power density the micro-turbomachinery must be run at tip speeds of order $500m∕s$, comparable to conventional scale turbomachinery. The high rotating speeds (of order 2 million rpm), the relatively low bearing aspect ratios $(L∕D<0.1)$ due to fabrication constraints, and the laminar flow regime in the bearing gap place the micro-bearing designs to an exotic spot in the design space for hydrostatic gas bearings. This paper presents a new analytical model for axially fed gas journal bearings and reports the experimental testing of micro gas bearings to characterize and to investigate their rotordynamic behavior. The analytical model is capable of dealing with all the elements of, (1) micro-devices, (2) dynamic response characteristics of hydrostatic gas bearings, (3) evaluation of stiffness, natural frequency and damping, (4) evaluation of instability boundaries, and (5) evaluation of effects of imbalance and bearing anisotropy. First, a newly developed analytical model for hydrostatic gas journal bearings is introduced. The model consists of two parts, a fluid dynamic model for axially fed gas journal bearings and a rotordynamic model for micro-devices. Next, the model is used to predict the natural frequency, damping ratio and the instability boundary for the test devices. Experiments are conducted using a high-resolution fiber optic sensor to measure rotor speed, and a data reduction scheme is implemented to obtain imbalance-driven whirl response curves. The model predictions are validated against experimental data and show good agreement with the measured natural frequencies and damping ratios. Last, the new model is successfully used to establish bearing operating protocols and guidelines for high-speed operation.

1.
Piekos
,
E.
,
Orr
,
D.
,
Jacobson
,
S.
,
Ehrich
,
F.
, and
Breuer
,
K.
, 1997, “
Design and Analysis of Microfabricated High Speed Gas Journal Bearings
,” In
28th AIAA Fluid Dynamics Conference
, Snowmass Village, Colorado, AIAA Paper 97-1966.
2.
Piekos
,
E.
, and
Breuer
,
K.
, 1999, “
Pseudospectral Orbit Simulation of Nonideal Gas-Lubricated Journal Bearings for Microfabricated Turbomachines
,”
ASME J. Tribol.
0742-4787,
121
[May], pp.
604
609
.
3.
Piekos
,
E.
, 2000,
Numerical Simulation of Gas-Lubricated Journal Bearings for Microfabricated Machines
, PhD thesis, Department of Aeronautics and Astronautics, MIT.
4.
Savoulides
,
N.
,
Piekos
,
E.
, and
Breuer
,
K.
, 2001, “
Low-Order Models for Very Short Hybrid Gas Bearings
,”
ASME J. Tribol.
0742-4787,
123
[Apr.], pp.
368
375
.
5.
Ehrich
,
F.
, and
Jacobson
,
S.
, 2001. “
Development of High-Speed Gas Bearings for High-Power-Density Micro-Devices
,” In
ASME Turbo Expo
, New Orleans, LA. Paper 2001-GT-478.
6.
Orr
,
D.
, 2000,
Macro-Scale Investigation of High Speed Gas Bearings for MEMS Devices
, PhD thesis, Department of Aeronautics and Astronautics, MIT.
7.
Larson
,
R.
, and
Richardson
,
H.
, 1962, “
A Preliminary Study of Whirl Instability for Pressurized Gas Bearings
,”
ASME J. Basic Eng.
0021-9223 Dec., pp.
511
520
.
8.
Childs
,
D.
, 1993,
Turbomachinery Rotordynamics - Phenomena, Modeling and Analysis
,
Wiley
, New York.
9.
San Andrés
,
L.
, and
Wilde
,
D.
, 2000, “
Finite Element Analysis of Gas Bearings for Oil-free Turbomachinery
,” In Tribology Report.
10.
Gong
,
Y.
, 2002., July, Personal communication,
MIT Gas Turbine Laboratory
.
11.
Savoulides
,
N.
, 2004,
Development of a MEMS Turbocharger and Gas Turbine Engine
, PhD thesis, Department of Aeronautics and Astronautics, MIT.
12.
Spakovszky
,
Z.
, and
Liu
,
L.
, 2004. “
Scaling Laws For Ultra-Short Hydrostatic Gas Journal Bearings
,”
ASME J. Vibr. Acoust.
0739-3717 (to be published).
13.
,
J.
, 2002., Aug. Personal communication,
MIT Gas Turbine Laboratory
.
14.
Miki
,
N.
,
Teo
,
C. J.
,
Ho
,
L.
, and
Zhang
,
X.
, 2000, “
Precision Fabrication of High-Speed Micro-Rotors Using Deep Reactive ion Etching (DRIE)
,” In
Hilton Head Solid-State Sensors and Actuators Workshop