In the present work, we report on an experimental study of bending/flap mode flutter of a blade within a linear cascade at transonic conditions. Driven by the motivation to understand the contribution of shock location/dynamics to flutter characteristics, we have performed simultaneous measurements of shock dynamics using high-speed shadowgraphy combined with unsteady load measurements on an oscillating blade within the cascade. The flutter characteristics in terms of energy transfer from the fluid to the blade and shock dynamics have been mapped out over a range of blade oscillation frequencies and static pressure ratios (SPR) across the cascade, the latter being important as it decides the mean location of the passage shocks. SPR values studied include both conditions where the shock is within the passage (started cascade) and where the passage shock is pushed ahead of the leading edge of the blades (unstarted cascade). These measurements show characteristically different flutter behaviour for an unstarted cascade compared with a started cascade, the former having received very little attention in the literature. While both these cases show small excitation levels at low reduced frequencies, the unstarted cascade case exhibits an additional relatively narrow region of excitation at higher reduced frequencies with approximately an order of magnitude higher excitation energies. Comparison of the shock dynamics between the two excitation regimes show significant differences in the phase of the leading edge shock in addition to changes in the suction side shock phase indicating that the two excitation regimes are of different origin.

Magnetic resonance thermometry (MRT) is a maturing diagnostic tool used to measure three-dimensional temperature fields. It has a great potential for investigating fluid flows within complex geometries leveraging medical grade magnetic resonance imaging (MRI) equipment and software along with novel measurement techniques. The efficacy of the method in engineering applications increases when coupled with other well-established MRI-based techniques such as magnetic resonance velocimetry (MRV). In this study, a challenging geometry is presented with the direct application to a complex gas turbine blade cooling scheme. Turbulent external flow with a Reynolds number of 136,000 passes a hollowed NACA-0012 airfoil with internal cooling features. Inserts within the airfoil, fed by a second flow line with an average temperature difference of 30 K from the main flow and a temperature-dependent Reynolds number in excess of 1,800, produces a conjugate heat transfer scenario including impingement cooling on the inside surface of the airfoil. The airfoil cooling scheme also includes zonal recirculation, surface film cooling, and trailing edge ejection features. The entire airfoil surface is constructed of a stereolithography resin—Accura 60—with low thermal conductivity. The three-dimensional internal and external velocity field is measured using an MRV. The fluid temperature field is measured within and outside of the airfoil with an MRT, and the results are compared with a computational fluid dynamics (CFD) solution to assess the current state of the art for combined MRV/MRT techniques for investigating these complex internal and external flows. The accompanying CFD analysis provides a prediction of the velocity and temperature fields, allowing for errors in the MRT technique to be estimated.

Impinging jet arrays are typically used to cool several gas turbine parts. Some examples of such applications can be found in the internal cooling of high-pressure turbine airfoils or in the turbine blade tip clearances control of aero-engines. The effect of the wall-to-jets temperature ratio (TR) on heat transfer is generally neglected by the correlations available in the open literature. In the present contribution, the impact of the temperature ratio on the heat transfer for a real engine active clearance control system is analyzed by means of validated computational fluid dynamics (CFD) computations. At different jets Reynolds number and considering several impingement array arrangements, a wide range of target wall-to-jets temperature ratio is accounted for. Computational results prove that both local and averaged Nusselt numbers reduce with increasing. An in-depth analysis of the numerical data shows that the last mentioned evidence is motivated by both the heat transfer incurring between the spent coolant flow and the fresh jets and the variation of gas properties with temperature through the boundary layer. A scaling procedure, based on the TR power law, was proposed to estimate the Nusselt number at different wall temperature levels necessary to correct available open-literature correlations, typically developed with small temperature differences, for real engine applications.

This paper numerically investigated the impact of the holes and their location on the flow and tip internal heat transfer in a U-bend channel (aspect ratio = 1:2), which is applicable to the cooling passage with dirt purge holes in the mid-chord region of a typical gas turbine blade. Six different tip ejection configurations are calculated at Reynolds numbers from 25,000 to 200,000. The detailed three-dimensional flow and heat transfer over the tip wall are presented, and the overall thermal performances are evaluated. The topological methodology, which is first applied to the flow analysis in an internal cooling passage of the blade, is used to explore the mechanisms of heat transfer enhancement on the tip wall. This study concludes that the production of the counter-rotating vortex pair in the bend region provides a strong shear force and then increases the local heat transfer. The side-mounted single hole and center-mounted double holes can further enhance tip heat transfer, which is attributed to the enhanced shear effect and disturbed low-energy fluid. The overall thermal performance of the optimum hole location is a factor of 1.13 higher than that of the smooth tip. However, if double holes are placed on the upstream of a tip wall, the tip surface cannot be well protected. The results of this study are useful for understanding the mechanism of heat transfer enhancement in a realistic gas turbine blade and for efficient designing of blade tips for engine service.

The combined action of Coriolis and centrifugal buoyancy forces results in nonuniform heat transfer coefficient on pressure and suction side internal walls, hence leading to nonuniform metal temperatures and increased thermal stresses. The present study addresses the problem of nonuniform heat transfer distribution due to rotation effect and proposes novel designs for serpentine cooling passages, which are arranged along the chord of the blade. The two configurations were four-passage and six-passage serpentine smooth channels. Detailed heat transfer coefficients were measured using transient liquid crystal thermography under stationary and rotating conditions. Heat transfer experiments were carried out for Reynolds numbers ranging from 12,294 to 85,000 under stationary conditions. Rotation experiments were carried out for the Rotation numbers of 0.05 and 0.11. Heat transfer enhancement levels of approximately two times the Dittus–Boelter correlation (for developed flow in smooth tubes) were obtained under stationary conditions. Under rotating conditions, we found that the four-passage configuration had slightly lower heat transfer compared with the stationary case, and the six-passage configuration had higher heat transfer on both the leading and trailing sides compared with the stationary case. The leading and trailing side heat transfer characteristics were near-similar to each other for both the configurations, and the rotating heat transfer was near-similar to the stationary condition heat transfer.

The present study deals with the application of the transient thermochromic liquid crystal (TLC) technique in a flow network of intersecting circular passages as a potential internal turbine component cooling geometry. The investigated network consists of six circular passages with a diameter d = 20 mm that intersect coplanar at an angle θ = 40 deg, the innermost in three, the outermost in one intersection level. Two additional nonintersecting passages serve as references. Such a flow network entails specific characteristics associated with the transient TLC method that have to be accounted for in the evaluation process: the strongly curved surfaces, the mixing and mass flow redistribution at each intersection point, and the resulting gradients between the wall and passage centerline temperatures. All this impedes the choice of a representative fluid reference temperature, which results in deviations using established evaluation methods. An alternative evaluation approach is introduced, which is supported by computational results obtained from steady-state three-dimensional (3D) Reynolds-averaged Navier–Stokes equations (RANS) simulations using the shear-stress transport (SST) turbulence model. The presented analysis uncouples local heat transfer (HT) coefficients from actually measured local temperatures but uses the time information of the thermocouples (TC) instead that represents the fluid temperature step change and evolution along the passages. This experimental time information is transferred to the steady-state numerical bulk temperatures, which are finally used as local references to evaluate the transient TLC experiments. As effective local mass flow rates in the passage sections are considered, the approach eventually allows for a conclusion whether HT is locally enhanced due to higher mass flow rates or the intersection effects.

The current industrial standard for numerical simulations of axial compressors is the steady Reynolds-averaged Navier–Stokes (RANS) approach. Besides the well-known limitations of mixing planes, namely their inherent inability to capture the potential interaction and the wakes from the upstream blades, there is another flow feature which is lost, and which is a major accountable for the radial mixing: the transport of streamwise vorticity. Streamwise vorticity is generated for various reasons, mainly associated with secondary and tip-clearance flows. A strong link exists between the strain field associated with the vortices and the mixing augmentation: the strain field increases both the area available for mixing and the local gradients in fluid properties, which provide the driving potential for the mixing. In the rear compressor stages, due to high clearances and low aspect ratios, only accounting for the development of secondary and clearance flow structures, it is possible to properly predict the spanwise mixing. In this work, the results of steady and unsteady simulations on a heavy-duty axial compressor are compared with experimental data. Adopting an unsteady framework, the enhanced mixing in the rear stages is properly captured, in remarkable agreement with experimental distributions. On the contrary, steady analyses strongly underestimate the radial transport. It is inferred that the streamwise vorticity associated with clearance flows is a major driver of radial mixing, and restraining it by pitch-averaging the flow at mixing planes is the reason why the steady approach cannot predict the radial transport in the rear part of the compressor.

Optimal turbine blade tip designs have the potential to enhance aerodynamic performance while reducing the thermal loads on one of the most vulnerable parts of the gas turbine. This paper describes a novel strategy to perform a multi-objective optimization of the tip geometry of a cooled turbine blade. The parameterization strategy generates arbitrary rim shapes around the coolant holes on the blade tip. The tip geometry performance is assessed using steady Reynolds-averaged Navier–Stokes simulations with the k– ω shear stress transport (SST) model for the turbulence closure. The fluid domain is discretized with hexahedral elements, and the entire optimization is performed using identical mesh characteristics in all simulations. This is done to ensure an adequate comparison among all investigated designs. Isothermal walls were imposed at engine-representative levels to compute the convective heat flux for each case. The optimization objectives were a reduction in heat load and an increase in turbine row efficiency. The multi-objective optimization is performed using a differential evolution strategy. Improvements were achieved in both the aerodynamic efficiency and heat load reduction, relative to a conventional squealer tip arrangement. Furthermore, this work demonstrates that the inclusion of over-tip coolant flows impacts the over-tip flow field, and that the rim–coolant interaction can be used to create a synergistic performance enhancement.

This article presents a brief review of the experimental and theoretical state of the art regarding the leakage flow prediction of brush seals. The authors model a computational fluid dynamics (CFD)-based approach for the leakage flow of brush seals. The brush seal is treated by modeling its real geometrical structure, namely numerous bristles in an array in transverse flow. The fluid domain is segregated into discrete volumes surrounding each bristle. Two different discretization schemes are chosen to study their influence on the leakage behavior. Furthermore, for each scheme multiple inter-bristle distances, pressure ratios and turbulence models are evaluated. In addition, the influence of irregular arrangement configurations, which forms a quasi-chaotic inner structure, is studied. The results gained are compared to other authors' experimental and numerical data.

The last 50 years has witnessed significant improvement in film cooling technologies while transpiration cooling is still not implemented in turbine airfoil cooling. Although transpiration cooling could provide higher cooling efficiency with less coolant consumption compared to film cooling, the fine pore structure and high porosity in transpiration cooling metal media always raised difficulties in conventional manufacturing. Recently, the rapid development of additive manufacturing (AM) has provided a new perspective to address such challenge. With the capability of the innovative powder bed selective laser metal sintering (SLMS) AM technology, the complex geometries of transpiration cooling part could be precisely fabricated and endued with improved mechanical strength. This study utilized the SLMS AM technology to fabricate the transpiration cooling and film cooling structures with Inconel 718 superalloy. Five different types of porous media including two perforated plates with different hole pitches, metal sphere packing, metal wire mesh, and blood vessel shaped passages for transpiration cooling were fabricated by EOS M290 system. One laidback fan-shaped film cooling coupon was also fabricated with the same printing process as the control group. Heat transfer tests under three different coolant mass flow rates and four different mainstream temperatures were conducted to evaluate the cooling performance of the printed coupons. The effects of geometry parameters including porosity, surface outlet area ratio, and internal solid–fluid interface area ratio were investigated as well. The results showed that the transpiration cooling structures generally had higher cooling effectiveness than film cooling structure. The overall average cooling effectiveness of blood vessel-shaped transpiration cooling reached 0.35, 0.5, and 0.57, respectively, with low (1.2%), medium (2.4%), and high (3.6%) coolant injection ratios. The morphological parameters analysis showed the major factor that affected the cooling effectiveness most was the internal solid–fluid interface area ratio for transpiration cooling. This study showed that additive manufactured transpiration cooling could be a promising alternative method for turbine blade cooling and worthwhile for further investigations.

The dimensionless model presented in part I of the corresponding paper to describe the flutter onset of two-fin rotating seals is exploited to extract valuable engineering trends with the design parameters. The analytical expression for the nondimensional work-per-cycle depends on three dimensionless parameters of which two of them are new. These parameters are simple but interrelate the effect of the pressure ratio, the height, and length of the interfin geometry, the seal clearance, the nodal diameter (ND), the fluid swirl velocity, the vibration frequency, and the torsion center location in a compact and intricate manner. It is shown that nonrelated physical parameters can actually have an equivalent impact on seal stability. It is concluded that the pressure ratio can be stabilizing or destabilizing depending on the case, whereas the swirl of the flow is always destabilizing. Finally, a simple method to extend the model to multiple interfin cavities, neglecting the unsteady interaction among them, is described.

A simple nondimensional model to describe the flutter onset of labyrinth seals is presented. The linearized mass and momentum integral equations for a control volume which represents the interfin seal cavity, retaining the circumferential unsteady flow perturbations created by the seal vibration, are used. First, the downstream fin is assumed to be choked, whereas in a second step the model is generalized for unchoked exit conditions. An analytical expression for the nondimensional work-per-cycle is derived. It is concluded that the stability of a two-fin seal depends on three nondimensional parameters, which allow explaining seal flutter behavior in a comprehensive fashion. These parameters account for the effect of the pressure ratio, the cavity geometry, the fin clearance, the nodal diameter (ND), the fluid swirl velocity, the vibration frequency, and the torsion center location in a compact and interrelated form. A number of conclusions have been drawn by means of a thorough examination of the work-per-cycle expression, also known as the stability parameter by other authors. It was found that the physics of the problem strongly depends on the nondimensional acoustic frequency. When the discharge time of the seal cavity is much greater than the acoustic propagation time, the damping of the system is very small and the amplitude of the response at the resonance conditions is very high. The model not only provides a unified framework for the stability criteria derived by Ehrich (1968, “Aeroelastic Instability in Labyrinth Seals,” ASME J. Eng. Gas Turbines Power, 90 (4), pp. 369–374) and Abbot (1981, “Advances in Labyrinth Seal Aeroelastic Instability Prediction and Prevention,” ASME J. Eng. Gas Turbines Power, 103 (2), pp. 308–312), but delivers an explicit expression for the work-per-cycle of a two-fin rotating seal. All the existing and well-established engineering trends are contained in the model, despite its simplicity. Finally, the effect of swirl in the fluid is included. It is found that the swirl of the fluid in the interfin cavity gives rise to a correction of the resonance frequency and shifts the stability region. The nondimensionalization of the governing equations is an essential part of the method and it groups physical effects in a very compact form. Part I of the paper details the derivation of the theoretical model and draws some preliminary conclusions. Part II of the corresponding paper analyzes in depth the implications of the model and outlines the extension to multiple cavity seals.

Gas turbine design has been characterized over the years by a continuous increase of the maximum cycle temperature, justified by a corresponding increase of cycle efficiency and power output. In such way, turbine components heat load management has become a compulsory activity, and then, a reliable procedure to evaluate the blades and vanes metal temperatures is, nowadays, a crucial aspect for a safe components design. In the framework of the design and validation process of high pressure turbine cooled components of the BHGE NovaLT TM 16 gas turbine, a decoupled methodology for conjugate heat transfer prediction has been applied and validated against measurement data. The procedure consists of a conjugate heat transfer analysis in which the internal cooling system (for both airfoils and platforms) is modeled by an in-house one-dimensional thermo-fluid network solver, the external heat loads and pressure distribution are evaluated through 3D computational fluid dynamics (CFD) analysis and the heat conduction in the solid is carried out through a 3D finite element method (FEM) solution. Film cooling effect has been treated by means of a dedicated CFD analysis, implementing a source term approach. Predicted metal temperatures are finally compared with measurements from an extensive test campaign of the engine in order to validate the presented procedure.

The degree of complexity in internal cooling designs is tied to the capabilities of the manufacturing process. Additive manufacturing (AM) grants designers increased freedom while offering adequate reproducibility of microsized, unconventional features that can be used to cool the skin of gas turbine components. One such desirable feature can be sourced from nature; a common characteristic of natural transport systems is a network of communicating channels. In an effort to create an engineered design that utilizes the benefits of those natural systems, the current study presents wavy microchannels that were connected using branches. Two different wavelength baseline configurations were designed; then each was numerically optimized using a commercial adjoint-based method. Three objective functions were posed to (1) minimize pressure loss, (2) maximize heat transfer, and (3) maximize the ratio of heat transfer to pressure loss. All baseline and optimized microchannels were manufactured using laser powder bed fusion (L-PBF) for experimental investigation; pressure loss and heat transfer data were collected over a range of Reynolds numbers. The AM process reproduced the desired optimized geometries faithfully. Surface roughness, however, strongly influenced the experimental results; successful replication of the intended flow and heat transfer performance was tied to the optimized design intent. Even still, certain test coupons yielded performances that correlated well with the simulation results.

The emerging renewable energy market calls for more advanced prediction tools for turbine transient operations in fast startup/shutdown cycles. Reliable numerical analysis of such transient cycles is complicated by the disparity in time scales of the thermal responses in fluid and solid domains. Obtaining fully coupled time-accurate unsteady conjugate heat transfer (CHT) results under these conditions would require to march in both domains using the time-step dictated by the fluid domain: typically, several orders of magnitude smaller than the one required by the solid. This requirement has strong impact on the computational cost of the simulation as well as being potentially detrimental to the accuracy of the solution due to accumulation of round-off errors in the solid. A novel loosely coupled CHT methodology has been recently proposed, and successfully applied to both natural and forced convection cases that remove these requirements through a source-term based modeling (STM) approach of the physical time derivative terms in the relevant equations. The method has been shown to be numerically stable for very large time steps with adequate accuracy. The present effort is aimed at further exploiting the potential of the methodology through a new adaptive time stepping approach. The proposed method allows for automatic time-step adjustment based on estimating the magnitude of the truncation error of the time discretization. The developed automatic time stepping strategy is applied to natural convection cases under long (2000 s) transients: relevant to the prediction of turbine thermal loads during fast startups/shutdowns. The results of the method are compared with fully coupled unsteady simulations showing comparable accuracy with a significant reduction of the computational costs.

Natural convection is an important heat transfer mode for flexible operations of gas turbines and steam turbines. Its prediction presents considerable challenges. The strong interdependence between fluid and solid parts points to the need for coupled fluid–solid conjugate heat transfer (CHT) methods. The fundamental fluid–solid time scale disparity is further compounded by the long-time scales of practical turbine flexible operations. In addition, if a high-fidelity flow model (e.g., large eddy simulation (LES)) is adopted to resolve turbulence fluctuations, extra mesh dependency on solid domain mesh may arise. In this work, understanding of the extra solid mesh dependency in a directly coupled LES based CHT procedure is gained by an interface response analysis, leading to a simple and clear characterization of erroneously predicted unsteady interface temperatures and heat fluxes. A loosely coupled unsteady CHT procedure based on a multiscale methodology for solving problems with large time scale disparity is subsequently developed. A particular emphasis of this work is on efficient and accurate transient CHT solutions in conjunction with the turbulence eddy resolved modeling (LES) for natural convection. A two-scale flow decomposition associated with a corresponding time-step split is adopted. The resultant triple-timing formation of the flow equations can be solved efficiently for the fluid–solid coupled system with disparate time scales. The problem statement, analysis, and the solution methods will be presented with case studies to underline the issues of interest and to demonstrate the validity and effectiveness of the proposed methodology and implemented procedure.

In turbomachinery design, the accurate prediction of the life cycle is one of the most challenging issues. Traditionally, life cycle calculations for radial turbine wheels of turbochargers focus on mechanical loads such as centrifugal and vibration forces. Due to the increase of exhaust gas temperatures in the last years, thermomechanical fatigue in the turbine wheel came more into focus. In order to account for the thermally induced stresses in the turbine wheel as a part of the standard design process, a fast method is required for predicting metal temperatures. In order to develop a suitable method, the mechanisms that cause the thermal stresses have to be understood. Thus, in a first step, a detailed analysis of the temperature fields is conducted in the present paper. Extensive numerical simulations of a thermal shock process are carried out and validated by experimental data from a test rig. Based on the results, the main heat transfer mechanisms are identified, which are crucial for the critical thermal stresses in transient operation. It is shown that these critical stresses mainly depend on local 3D flow structures. With this understanding, two fast methods to calculate the transient temperatures in a radial turbine were developed. The first method is based on a standard method for transient fluid/solid heat transfer. In this standard method, heat transfer coefficients are derived from steady-state computational fluid dynamics (CFD)/conjugate heat transfer (CHT) calculations and are linearly interpolated over the duration of the transient heating or cooling process. In the new method, this interpolation procedure was modified to achieve an exponential behavior of the heat transfer coefficients over the transient process in order to enable a sufficient accuracy. Additionally, a second method was developed. In this method, the specific heat capacity of the solid state is reduced by a “speed up factor” to shorten the duration of the transient heating or cooling process. With the shortened processes, the computing times can be reduced significantly. After the calculations, the resulting times are transferred into realistic heating or cooling times by multiplying them with the speed up factor. The results of both methods are evaluated against experimental data and against the results of a numerical method known from literature. The methods show a good agreement with those data.

Organic Rankine cycle (ORC) turbogenerators are the most viable option to convert sustainable energy sources in the low-to-medium power output range (from tens of kW e to several MW e ). The design of efficient ORC turbines is particularly challenging due to their inherent unsteady nature (high expansion ratios and low speed of sound of organic compounds) and to the fact that the expansion encompasses thermodynamic states in the dense vapor region, where the ideal gas assumption does not hold. This work investigates the unsteady nonideal fluid dynamics and performance of a high expansion ratio ORC turbine by means of detailed Reynolds-averaged Navier–Stokes (RANS) simulations. The complex shock interactions resulting from the supersonic flow (M ≈ 2.8 at the vanes exit) are related to the blade loading, which can fluctuate up to 60% of the time-averaged value. A detailed loss analysis shows that shock-induced boundary layer separation on the suction side of the rotor blades is responsible for most of the losses in the rotor, and that further significant contributions are given by the boundary layer in the diverging part of the stator and by trailing edge losses. Efficiency loss due to unsteady interactions is quantified in 1.4% in absolute percentage points at design rotational speed. Thermophysical properties are found to feature large variations due to temperature even after the strong expansion in the nozzle vanes, thus supporting the use of accurate fluid models in the whole turbine stage.

The present work is part of a detailed aerothermal investigation in a model of a rotating internal cooling channel performed in a novel facility setup which allows test conditions at high rotation numbers ( Ro ). The test section is mounted on a rotating frame with all the required instrumentation, resulting in a high spatial resolution and accuracy. The channel has a cross section with an aspect ratio of 0.9 and a ribbed wall with eight ribs perpendicular to the main flow direction. The blockage of the ribs is 10% of the channel cross section, whereas the rib pitch-to-height ratio is 10. In this first part of the paper, the flow over the wall region between the sixth and seventh ribs in the symmetry plane is investigated by means of two-dimensional particle image velocimetry (PIV). Tests were carried out at a Reynolds number ( Re ) of 15,000 in static and rotating conditions, with a maximum Ro of 0.77. Results are in good agreement with the data present in literature at the same Reynolds number and with rotation numbers of 0 (static conditions) and 0.38 in a channel with the same geometry as in the present work. When Ro is increased from 0.38 to 0.77, the main velocity and turbulence fields show important changes. At a rotation number of 0.77, although the extension of the recirculation bubble after the sixth rib on the trailing side does not vary significantly, it covers the full inter-rib area on the leading side in the streamwise direction. The turbulence intensity on the leading side shows a low value with respect to the static case but roughly at the same level as in the lower Ro case. On the trailing side, the maximum value of the turbulence intensity slightly decreases from Ro = 0.38 to Ro = 0.77, the wall shear layer is restabilized along the second half of the pitch due to the high rotation, and the secondary flows are redistributed causing spanwise vortex compression. The observed result is the rapid decay of turbulent fluctuations in the second half of the inter-rib area.

An investigation to characterize the effect of entrainment in a confined jet impingement arrangement is presented. The investigated configuration shows an impingement-cooled turbine blade passage and holds two staggered rows of inclined impingement jets. In order to distinctly promote thermal entrainment phenomena, the jets were heated separately. A steady-state liquid crystal technique was used to obtain near-wall fluid temperature distributions for the impingement surfaces under adiabatic conditions. Additionally, flow field measurements were undertaken using particle image velocimetry (PIV). Furthermore, compressible Reynolds-averaged Navier–Stokes (RANS) simulations carried out with ansys cfx using Menter's shear stress transport (SST) turbulence model accompany the experiments. Distributions of effectiveness, velocity, and turbulent kinetic energy detail the complexity of the aerothermal situation. The study was conducted for a jet Reynolds number range from 10,000 to 45,000. The experimental and numerical results are generally in good agreement. Nevertheless, the simulations predict flow features in particular regions of the geometry that are not as prominent in the experiments. These affect the effectiveness distributions, locally. The investigations reveal that the effectiveness is independent of the temperature difference between the heated and cold jet as well as the jet Reynolds number.