Abstract

Aspect ratio and solidity play complementary roles in the aerodynamic design of axial fan rotor blades. Few studies have experimented the effect of the aspect ratio of rotor blades on the performance of low-speed axial fans or its interaction with blade solidity in terms of fan aerodynamic performance. This study examined the selection of the solidity and blade aspect ratio in the preliminary design of low-pressure industrial fans with minimized hub-to-tip ratios. The aim of this study was to make available to the fan community experimental data that allow the determination of the optimal aspect ratio for practical applications as a function of the blade solidity. Various aspects of the performance of 16 prototypes of a 315-mm-diameter propeller fan were compared. The industrial fan prototypes all had a hub-to-tip ratio of 0.2 and were derived from four baseline designs conceived to ideally achieve the same best efficiency operation with different values of the aspect ratio. In addition, the prototypes’ assemblies were conceived to allow operation with different blade counts, i.e., with different rotor solidities at a fixed blade aspect ratio. The aerodynamic performance of the fans, measured in accordance with the ISO-5801 standard, was evaluated to assess the sensitivity and trends of the fan pressure and efficiency with respect to the blade aspect ratio and solidity at fixed tip clearance. The measured effects of the aspect ratio and solidity are discussed on the basis of data available in the literature. The results of the experimental analysis were used to formulate general guidelines for the preliminary design of propeller fans with minimized hub-to-tip ratios.

References

1.
Angelini
,
G.
,
Corsini
,
A.
,
Delibra
,
G.
, and
Tieghi
,
L.
,
2019
, “
A Multidimensional Extension of Balje Chart for Axial Flow Turbomachinery Using Artificial Intelligence-Based Meta-Models
,”
ASME J. Eng. Gas Turbines Power
,
141
(
11
), p.
111012
.
2.
To
,
H.
, and
Miller
,
R. J.
,
2019
, “
The Effect of Aspect Ratio on Compressor Performance
,”
ASME J. Turbomach.
,
141
(
8
), p.
081011
.
3.
Masi
,
M.
,
Da Lio
,
L.
, and
Lazzaretto
,
A.
,
2020
, “
An Insight Into the Similarity Approach to Predict the Maximum Efficiency of Organic Rankine Cycle Turbines
,”
Energy
,
198
, p.
117278
.
4.
Lewis
,
R. I.
,
1996
,
Turbomachinery Performance Analysis
,
Arnold
,
London
.
5.
ISO—International Organization for Standard—Technical Committee ISO/TC 117, Fans
,
2007
, “
Industrial Fans—Performance Testing Using Standardized Airways
.” ISO 5801:2007, CP 401—1214 Vernier, Geneva, Switzerland.
6.
Masi
,
M.
,
Fontana
,
F.
, and
Lazzaretto
,
A.
,
2017
, “
On the Choice of Suitable Parameters for the Assessment of Industrial Fans Performance and Efficiency
,”
Proceedings of the ASME TurboExpo 2017
,
Charlotte, NC
,
June 26–30
, Paper No. GT2017-64032.
7.
Wilkinson
,
M. B.
,
Van Der Spuy
,
J.
, and
Von Backström
,
T. W.
,
2017
, “
The Design of a Large Diameter Axial Flow Fan for Air-Cooled Heat Exchanger Applications
,”
Proceedings of the ASME TurboExpo 2017
,
Charlotte, NC
,
June 26–30
, Paper No. GT2017-63331.
8.
Eck
,
B.
,
1973
,
Fans
,
Pergamon Press
,
Oxford, UK
.
9.
Wallis
,
R. A.
,
1993
,
Axial Flow Fans and Ducts
,
Krieger Publishing
,
Malabar
.
10.
Bleier
,
P. F.
,
1988
,
Fan Handbook—Selection, Application and Design
,
McGraw-Hill
,
New York
.
11.
McKenzie
,
A. B.
,
1997
,
Axial Flow Fans and Compressors—Aerodynamic Design and Performance
,
Ashgate
,
Aldershot, UK
.
12.
Peters
,
M.
,
Schmidt
,
T.
, and
Jeschke
,
P.
,
2019
, “
Influence of Blade Aspect Ratio on Axial Compressor Efficiency
,”
J. Global Power Propul. Soc.
,
3
, pp.
639
652
.
13.
Theis
,
A.
, and
Böhle
,
M.
,
2021
, “
Influence of the Rotor Blade Aspect Ratio on the Performance of an Axial Fan
,”
J. Phys.: Conf. Ser.
,
1909
, p.
012022
.
14.
Wang
,
J.
, and
Kruyt
,
N. P.
,
2020
, “
Computational Fluid Dynamics Simulations of Aerodynamic Performance of Low-Pressure Axial Fans With Small Hub-to-Tip Diameter Ratio
,”
ASME J. Fluids Eng.
,
142
(
9
), p.
091292
.
15.
Masi
,
M.
,
Lazzaretto
,
A.
,
Danieli
,
P.
, and
Bettanini
,
C.
,
2022
, “
Design of a Small Axial-Flow Fan With 0.2 Hub-to-Tip Ratio
,”
Proceedings of FAN 2022 Conference
,
Senlis, France
,
June 27–29
.
16.
Cory
,
W. T. W.
,
2005
,
Fans & Ventilation—A Practical Guide
,
Elsevier Ltd
,
Amsterdam, The Netherlands
.
17.
Masi
,
M.
,
Danieli
,
P.
, and
Lazzaretto
,
A.
,
2022
, “
Overview of the Best 2020 Axial-Flow Fan Data and Inclusion in Similarity Charts for the Search of the Best Design
,”
ASME J. Turbomach.
,
144
(
9
), p.
091012
.
18.
ESDU—Engineering Sciences Data Unit
,
1980
, “
A Guide to Fan Selection and Performance
,” ESDU 79037.
19.
Balje
,
O. E.
,
1981
,
Turbomachines—A Guide to Design, Selection, and Theory
,
John Wiley & Sons
,
New York
.
20.
Masi
,
M.
, and
Lazzaretto
,
A.
,
2019
, “
A New Practical Approach to the Design of Industrial Axial Fans: Tube-Axial Fans With Very Low Hub-to-Tip Ratio
,”
ASME J. Eng. Gas Turbines Power
,
141
(
10
), p.
101003
.
21.
Castegnaro
,
S.
,
Masi
,
M.
, and
Lazzaretto
,
A.
,
2018
, “
Design and Testing of an ISO 5801 Inlet Chamber Test Rig and Related Issues With the Standard
,”
Proceedings of Fan 2018 Conference
,
Darmstadt, Germany
,
April 18–20
.
22.
Danieli
,
P.
,
Masi
,
M.
,
Delibra
,
G.
,
Corsini
,
A.
, and
Lazzaretto
,
A.
,
2021
, “
Assessment of MULTALL as Computational Fluid Dynamics Code for the Analysis of Tube-Axial Fans
,”
ASME J. Turbomach.
,
143
(
7
), p.
071005
.
23.
Downie
,
R. J.
,
Thompson
,
M. C.
, and
Wallis
,
R. A.
,
1993
, “
An Engineering Approach to Blade Designs for Low to Medium Pressure Rise Rotor-Only Axial Fans
,”
Exp. Therm. Fluid. Sci.
,
6
(
4
), pp.
376
401
.
You do not currently have access to this content.