Thermal closure of the engine casing is widely used to minimize undesirable blade tip leakage flows thus improving jet engine performance. This may be achieved using an impingement cooling scheme on the external casing wall, provided by manifolds attached to the outside of the engine. The assembly tolerance of these components leads to variation in the standoff distance between the manifold and the casing, and its effects on casing contraction must be understood to allow build tolerance to be specified. For cooling arrangements with promising performance, the variation in closure with standoff distance of z/d = 1–6 were investigated through a mixture of extensive numerical modeling and experimental validation. A cooling manifold, typical of that adopted by several engine companies, incorporating three different arrays of short cooling holes (chosen from previous study by Choi et al. (2016, “The Relative Performance of External Casing Impingement Cooling Arrangements for Thermal Control of Blade Tip Clearance,” ASME J. Turbomach., 138(3), p. 031005.)) and thermal control dummy flanges were considered. Typical contractions of 0.5–2.2 mm are achieved from the 0.02–0.35 kg/s of the current casing cooling flows. The variation in heat transfer coefficient observed with standoff distance is much lower for the sparse array investigated compared to previous designs employing arrays typical of blade cooling configurations. The reason for this is explained through interrogation of the local flow field and resultant heat transfer coefficient. This implies that acceptable control of the circumferential uniformity of case cooling can be achieved with relatively large assembly tolerance of the manifold relative to the casing.
Skip Nav Destination
Article navigation
February 2018
Research-Article
The Effect of External Casing Impingement Cooling Manifold Standoff Distance on Casing Contraction for Thermal Control of Blade Tip Clearance
Myeonggeun Choi,
Myeonggeun Choi
Department of Engineering Science,
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: myeonggeun.choi@eng.ox.ac.uk
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: myeonggeun.choi@eng.ox.ac.uk
Search for other works by this author on:
David R. H. Gillespie,
David R. H. Gillespie
Department of Engineering Science,
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: david.gillespie@eng.ox.ac.uk
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: david.gillespie@eng.ox.ac.uk
Search for other works by this author on:
Leo V. Lewis
Leo V. Lewis
Search for other works by this author on:
Myeonggeun Choi
Department of Engineering Science,
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: myeonggeun.choi@eng.ox.ac.uk
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: myeonggeun.choi@eng.ox.ac.uk
David R. H. Gillespie
Department of Engineering Science,
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: david.gillespie@eng.ox.ac.uk
University of Oxford,
Oxford OX1 3PJ, UK
e-mail: david.gillespie@eng.ox.ac.uk
Leo V. Lewis
Contributed by the International Gas Turbine Institute (IGTI) of ASME for publication in the JOURNAL OF TURBOMACHINERY. Manuscript received August 16, 2017; final manuscript received October 6, 2017; published online November 29, 2017. Editor: Kenneth Hall.
J. Turbomach. Feb 2018, 140(2): 021005 (13 pages)
Published Online: November 29, 2017
Article history
Received:
August 16, 2017
Revised:
October 6, 2017
Citation
Choi, M., Gillespie, D. R. H., and Lewis, L. V. (November 29, 2017). "The Effect of External Casing Impingement Cooling Manifold Standoff Distance on Casing Contraction for Thermal Control of Blade Tip Clearance." ASME. J. Turbomach. February 2018; 140(2): 021005. https://doi.org/10.1115/1.4038280
Download citation file:
Get Email Alerts
Cited By
A Digital Engineering Analysis of an Additively-Manufactured Turbine Vane
J. Turbomach (May 2025)
Mode Analysis for the Rotating Aerodynamic Disturbance of a Transonic Fan
J. Turbomach (May 2025)
Effect of Ceramic Matrix Composites on the Thermal Efficiency of a Power Generation Turbine
J. Turbomach (May 2025)
Heat Transfer Enhancement in Pulsating Flows: A Bayesian Approach to Experimental Correlations
J. Turbomach (May 2025)
Related Articles
The Relative Performance of External Casing Impingement Cooling Arrangements for Thermal Control of Blade Tip Clearance
J. Turbomach (March,2016)
Investigation of Unsteady Flow Phenomena in First Vane Caused by Combustor Flow With Swirl
J. Turbomach (April,2017)
Erratum: “Film Cooling Extraction Effects on the Aero-Thermal Characteristics of Rib Roughened Cooling Channel Flow” [ASME J. Turbomach., 135(2), p. 021016; DOI: 10.1115/1.4007501 ]
J. Turbomach (August,2018)
The Optimal Distribution of Pin Fins for Blade Tip Cap Underside Cooling
J. Turbomach (January,2015)
Related Proceedings Papers
Related Chapters
Control and Operational Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Thermodynamic Performance
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Outlook
Closed-Cycle Gas Turbines: Operating Experience and Future Potential