In gas turbine engines, film cooling holes are commonly fed with an internal crossflow, the magnitude of which has been shown to have a notable effect on film cooling effectiveness. In Part I of this study, as well as in a few previous studies, the magnitude of internal crossflow velocity was shown to have a substantial effect on film cooling effectiveness of axial shaped holes. There is, however, almost no data available in the literature that shows how internal crossflow affects compound angle shaped film cooling holes. In Part II, film cooling effectiveness, heat transfer coefficient augmentation, and discharge coefficients were measured for a single row of compound angle shaped film cooling holes fed by internal crossflow flowing both in-line and counter to the spanwise direction of coolant injection. The crossflow-to-mainstream velocity ratio was varied from 0.2 to 0.6 and the injection velocity ratio was varied from 0.2 to 1.7. It was found that increasing the magnitude of the crossflow velocity generally caused degradation of the film cooling effectiveness, especially for in-line crossflow. An analysis of jet characteristic parameters demonstrated the importance of crossflow effects relative to the effect of varying the film cooling injection rate. Heat transfer coefficient augmentation was found to be primarily dependent on injection rate, although for in-line crossflow, increasing crossflow velocity significantly increased augmentation for certain conditions.

References

References
1.
Bunker
,
R. S.
,
2005
, “
A Review of Shaped Hole Turbine Film-Cooling Technology
,”
ASME J. Heat Transfer
,
127
(
4
), pp.
441
453
.
2.
Taslim
,
M. E.
, and
Khanicheh
,
A.
,
2005
, “
Film Effectiveness Downstream of an Row of Compound Angle Holes
,”
ASME J. Heat Transfer
,
127
(
4
), pp.
434
440
.
3.
Bell
,
C. M.
,
Hamakawa
,
H.
, and
Ligrani
,
P. M.
,
2000
, “
Film Cooling from Shaped Holes
,”
ASME J. Heat Transfer
,
122
(
2
), pp.
224
232
.
4.
Ganzert
,
W.
,
Hildebrandt
,
T.
, and
Fottner
,
L.
,
2000
, “
Systematic Experimental and Numerical Investigations on the Aerothermodynamics of a Film Cooled Turbine Cascade With Variation of the Cooling Hole Shape—Part I: Experimental Approach
,”
ASME
Paper No. 2000-GT-0295.
5.
Gritsch
,
M.
,
Schulz
,
A.
, and
Wittig
,
S.
,
2003
, “
Effect of Internal Coolant Crossflow on the Effectiveness of Shaped Film-Cooling Holes
,”
ASME J. Turbomach.
,
125
(
3
), pp.
547
554
.
6.
Saumweber
,
C.
, and
Schulz
,
A.
,
2012
, “
Effect of Geometry Variations on the Cooling Performance of Fan-Shaped Cooling Holes
,”
ASME J. Turbomach.
,
134
(
6
), p.
061008
.
7.
Wilkes
,
E. K.
,
Anderson
,
J. B.
,
McClintic
,
J. W.
, and
Bogard
,
D. G.
,
2016
, “
An Investigation of Turbine Film Cooling Effectiveness With Shaped Holes and Internal Cross-Flow with Varying Operational Parameters
,”
ASME
Paper No. GT2016-56162.
8.
McClintic
,
J. W.
,
Anderson
,
J. B.
,
Bogard
,
D. G.
,
Dyson
,
T. E.
, and
Webster
,
Z.
,
2017
, “
Effect of Internal Crossflow Velocity on Film Cooling Effectiveness—Part I: Axial Shaped Holes
,”
ASME
Paper No. GT2017-64624.
9.
McClintic
,
J. W.
,
Klavetter
,
S. R.
,
Winka
,
J. R.
,
Anderson
,
J. B.
,
Bogard
,
D. G.
,
Dees
,
J. E.
,
Laskowski
,
G. M.
, and
Briggs
,
R.
,
2015
, “
The Effect of Internal Crossflow on the Adiabatic Effectiveness of Compound Angle Film Cooling Holes
,”
ASME J. Turbomach.
,
137
(
7
), p.
071006
.
10.
Stratton
,
Z. T.
,
Shih
,
T. I.
,
Laskowski
,
G. M.
,
Barr
,
B.
, and
Briggs
,
R.
,
2015
, “
Effects of Crossflow in an Internal-Cooling Channel on Film Cooling of a Flat Plate Through Compound-Angle Holes
,”
ASME
Paper No. GT2015-42771.
11.
Dittmar
,
J.
,
Schulz
,
A.
, and
Wittig
,
S.
,
2002
, “
Assessment of Various Film Cooling Configurations Including Shaped and Compound Angle Holes Based on Large Scale Experiments
,”
ASME
Paper No. GT2002-30176.
12.
Anderson
,
J. B.
,
Wilkes
,
E. K.
,
McClintic
,
J. W.
, and
Bogard
,
D. G.
,
2016
, “
Effects of Freestream Mach Number, Reynolds Number, and Boundary Layer Thickness on Film Cooling Effectiveness of Shaped Holes
,”
ASME
Paper No. GT2016-56152.
13.
Schroeder
,
R. P.
, and
Thole
,
K. A.
,
2014
, “
Adiabatic Effectiveness Measurements for a Baseline Shaped Film Cooling Hole
,”
ASME
Paper No. GT2014-25992.
14.
Gritsch
,
M.
,
Saumweber
,
C.
,
Schulz
,
A.
,
Wittig
,
S.
, and
Sharp
,
E.
,
2000
, “
Effect of Internal Coolant Crossflow Orientation on the Discharge Coefficient of Shaped Film-Cooling Holes
,”
ASME J. Turbomach.
,
122
(
1
), pp.
146
152
.
15.
Klavetter
,
S. R.
,
McClintic
,
J. W.
,
Bogard
,
D. G.
,
Dees
,
J. E.
,
Laskowski
,
G. M.
, and
Briggs
,
R.
,
2016
, “
The Effect of Rib Turbulators on Film Cooling Effectiveness of Round Compound Angle Holes Fed by an Internal Cross-Flow
,”
ASME J. Turbomach.
,
138
(
12
), p.
121006
.
16.
Dyson
,
T. E.
,
McClintic
,
J. W.
,
Bogard
,
D. G.
, and
Bradshaw
,
S. D.
,
2013
, “
Adiabatic and Overall Effectiveness for a Fully Cooled Turbine Vane
,”
ASME
Paper No. GT2013-94928.
17.
Moffat
,
R. J.
,
1985
, “
Using Uncertainty Analysis in the Planning of an Experiment
,”
ASME J. Fluids Eng.
,
107
(
2
), pp.
173
178
.
18.
Anderson
,
J. B.
,
McClintic
,
J. W.
,
Bogard
,
D. G.
,
Dyson
,
T. E.
, and
Webster
,
Z.
,
2017
, “
Freestream Flow Effects on Film Effectiveness and Heat Transfer Coefficeint Augmentation for Compound Angle Shaped Holes
,”
ASME
Paper No. GT2017-64853.
You do not currently have access to this content.