This paper presents a comparative numerical study of turbulent flow inside a two-pass internal cooling channel with different bend geometries. The goal is to find a geometry that reduces the bend related pressure loss and enhances overall heat transfer coefficient. A square channel with a round U-bend is taken as a baseline case and the heat transfer and pressure drop for nine different bend geometries are compared with the baseline. Modifications for the bend geometry are made along the channel divider wall and at the end wall of the 180 deg bend. The bend geometries studied include: (1) a turning vane geometry, (2) an asymmetrical bulb, (3) three different symmetrical bulbs, (4) two different bow shaped geometries at the end wall, (5) a bend with an array of dimples in the bend region, and (6) finally a combination of bow geometry and dimples. The solution procedure is based on a commercial finite volume solver using the Reynolds averaged Navier–Stokes (RANS) equation and a turbulence model. A two equation realizable k-ɛ model with enhanced wall treatment is used to model the turbulent flow. It was found that the bend geometry can have a significant effect on the overall performance of a two-pass channel. The modified bend geometries are compared with the baseline using Nusselt number ratios, friction factor ratios, and thermal performance factors (TPF) as the metrics. All the modified bend geometries show increase in the TPF with the symmetrical bulb configuration showing nearly a 40% reduction in friction factor ratio and a 30% increase in thermal performance. The highest TPF (41% increase over baseline) is observed for the symmetrical bulb combined with a bow along the outer walls and surface dimples.
Skip Nav Destination
Article navigation
March 2013
Research-Article
Effect of Bend Geometry on Heat Transfer and Pressure Drop in a Two-Pass Coolant Square Channel for a Turbine
Sumanta Acharya
Sumanta Acharya
1
e-mail: acharya@tigers.lsu.edu
Turbine Innovation and Energy Research (TIER) Center,
Mechanical Engineering Department,
Turbine Innovation and Energy Research (TIER) Center,
Mechanical Engineering Department,
Louisiana State University
,Baton Rouge, LA 70803
1Corresponding author
Search for other works by this author on:
Sumanta Acharya
e-mail: acharya@tigers.lsu.edu
Turbine Innovation and Energy Research (TIER) Center,
Mechanical Engineering Department,
Turbine Innovation and Energy Research (TIER) Center,
Mechanical Engineering Department,
Louisiana State University
,Baton Rouge, LA 70803
1Corresponding author
Contributed by the International Gas Turbine Institute (IGTI) of ASME for publication in the JOURNAL OF TURBOMACHINERY. Manuscript received September 19, 2011; final manuscript received January 10, 2012; published online November 8, 2012. Editor: David Wisler.
J. Turbomach. Mar 2013, 135(2): 021035 (12 pages)
Published Online: November 8, 2012
Article history
Received:
September 19, 2011
Revision Received:
January 10, 2012
Citation
Saha, K., and Acharya, S. (November 8, 2012). "Effect of Bend Geometry on Heat Transfer and Pressure Drop in a Two-Pass Coolant Square Channel for a Turbine." ASME. J. Turbomach. March 2013; 135(2): 021035. https://doi.org/10.1115/1.4006665
Download citation file:
Get Email Alerts
Related Articles
Bend Geometries in Internal Cooling Channels for Improved Thermal Performance
J. Turbomach (May,2013)
Heat Transfer and Flow Resistance Characteristics of Louver Fin Geometry for Automobile Applications
J. Heat Transfer (October,2011)
A Design and Rating Method for Shell-and-Tube Heat Exchangers With Helical Baffles
J. Heat Transfer (May,2010)
Related Proceedings Papers
Related Chapters
Adding Surface While Minimizing Downtime
Heat Exchanger Engineering Techniques
Summary
Heat Transfer & Hydraulic Resistance at Supercritical Pressures in Power Engineering Applications
Performance Testing of Combined Cycle Power Plant
Handbook for Cogeneration and Combined Cycle Power Plants, Second Edition