A single-stage transonic axial compressor was equipped with a casing treatment (CT), consisting of 3.5 axial slots per rotor pitch in order to investigate the predicted extension of the stall margin characteristics both numerically and experimentally. Contrary to most other studies, the CT was designed especially accounting for an optimized optical access in the immediate vicinity of the CT, rather than giving maximum benefit in terms of stall margin extension. Part I of this two-part contribution describes the experimental investigation of the blade tip interaction with casing treatment using particle image velocimetry (PIV). The nearly rectangular geometry of the CT cavities allowed a portion of it to be made of quartz glass with curvatures matching the casing. Thus, the flow phenomena could be observed with essentially no disturbance caused by the optical access. Two periscope light sheet probes were specifically designed for this application to allow for precise alignment of the laser light sheet at three different radial positions in the rotor passage (87.5%, 95%, and 99%). For the outermost radial position, the light sheet probe was placed behind the rotor and aligned to pass the light sheet through the blade tip clearance. It was demonstrated that the PIV technique is capable of providing velocity information of high quality even in the tip clearance region of the rotor blades. The chosen type of smoke-based seeding with very small particles (about 0.5μm in diameter) supported data evaluation with high spatial resolution, resulting in a final grid size of 0.5×0.5mm2. The PIV database established in this project forms the basis for further detailed evaluations of the flow phenomena present in the transonic compressor stage with CT and allows validation of accompanying computational fluid dynamics (CFD) calculations using the TRACE code. Based on the combined results of PIV measurements and CFD calculations of the same compressor and CT geometry, a better understanding of the complex flow characteristics can be achieved, as detailed in Part II of this paper.

1.
Westerweel
,
J.
, 2000, “
Theoretical Analysis of the Measurement Precision in Particle Image Velocimetry
,”
Exp. Fluids
0723-4864,
29
, pp.
S3
S12
.
2.
Wereley
,
S. T.
, and
Meinhart
,
C. D.
, 2001, “
Second-Order Accurate Particle Image Velocimetry
,”
Exp. Fluids
0723-4864,
31
, pp.
258
268
.
3.
Raffel
,
M.
,
Willert
,
C.
,
Wereley
,
S.
, and
Kompenhans
,
J.
, 2007,
Particle Image Velocimetry, A Practical Guide
,
2nd ed.
,
Springer
,
Berlin
.
4.
Hojo
,
M.
,
Hayami
,
H.
, and
Aramaki
,
S.
, 2003, “
3D Configuration of Shock Wave in Transonic Centrifugal Impeller Using 2D-PIV
,”
Proceedings of the International Gas Turbine Congress
, Tokyo, Nov. 2–7.
5.
Wernet
,
M. P.
, 2000, “
Application of DPIV to Study Both Steady State and Transient Turbomachinery Flows
,”
Opt. Laser Technol.
0030-3992,
32
, pp.
497
525
.
6.
Voges
,
M.
,
Beversdorff
,
M.
,
Willert
,
C.
, and
Krain
,
H.
, 2007, “
Application of Particle Image Velocimetry to a Transonic Centrifugal Compressor
,”
Exp. Fluids
0723-4864,
43
, pp.
371
384
.
7.
Wernet
,
M. P.
,
van Zante
,
D.
,
Strazisar
,
T. J.
,
John
,
W. T.
, and
Prahst
,
P. S.
, 2005, “
Characterization of Tip Clearance Flow in an Axial Compressor Using 3-D Digital PIV
,”
Exp. Fluids
0723-4864,
39
, pp.
743
754
.
8.
Liu
,
B.
,
Yu
,
X.
,
Liu
,
H.
,
Jiang
,
H.
,
Yuan
,
H.
, and
Xu
,
Y.
, 2006, “
Application of SPIV in Turbomachinery
,”
Exp. Fluids
0723-4864,
40
, pp.
621
642
.
9.
Woisetschläger
,
J.
,
Mayrhofer
,
N.
,
Hampel
,
B.
,
Lang
,
H.
, and
Sanz
,
W.
, 2003, “
Laser-Optical Investigation of Turbine Wake Flow
,”
Exp. Fluids
0723-4864,
34
, pp.
371
378
.
10.
Lu
,
X.
, and
Zhu
,
J.
, 2006, “
Experimental and Numerical Investigation of a Subsonic Compressor With Bend Skewed Slots Casing Treatment
,” ASME Paper No. GT2006-90026.
11.
Müller
,
M. W.
,
Schiffer
,
H. P.
, and
Hah
,
C.
, 2007, “
Effect of Circumferential Grooves in the Aerodynamic Performance of an Axial Single-Stage Transonic Compressor
,” ASME Paper No. GT2007-27365.
12.
Emmrich
,
R.
,
Hoehnen
,
H.
, and
Niehus
,
R.
, 2007, “
Time Resolved Investigations of an Axial Compressor With Casing Treamant
,” ASME Paper Nos. GT2007-27581 and GT2007-27582.
13.
Greitzer
,
E. M.
,
Nikkanen
,
J. P.
,
Haddad
,
D. E.
,
Mazzaway
,
R. S.
, and
Joslyn
,
H. D.
, 1979, “
A Fundamental Criterion for the Application of Rotor Casing Treatment
,”
ASME J. Fluids Eng.
0098-2202,
101
, pp.
237
243
.
14.
Hathaway
,
M. D.
, 2002, “
Self-Recirculating Casing-Treatment Concept for Enhanced Compressor Performance
,” ASME Paper No. GT2002-30368.
15.
Wilke
,
I.
, and
Kau
,
H. -P.
, 2003, “
A Numerical Investigation of the Flow Mechanisms in a HPC Front Stage With Axial Slots
,” ASME Paper No. GT2003-38481.
16.
Yang
,
H.
,
Nuernberger
,
D.
,
Nicke
,
E.
, and
Weber
,
A.
, 2003, “
Numerical Investigation of Casing Treatment Mechanisms With a Conservative Mixed-Cell Approach
,” ASME Paper No. GT2003-38483.
17.
Yang
,
H.
,
Nürnberger
,
D.
, and
Kersken
,
H. -P.
, 2006, “
Towards Excellence in Turbomachinery Computational Fluid Dynamics: A Hybrid Structured-Unstructured Reynolds-Averaged Navier–Stokes Solver
,
ASME J. Turbomach.
0889-504X,
128
, pp.
390
402
.
18.
Lu
,
X.
,
Zhu
,
J.
, 2005, “
The Effects of Bend Skewed Groove Casing Treastment on Performance and Flow Field Near the Endwall of an Axial Compressor
,” AIAA Paper No. 2005-809.
19.
Roesgen
,
T.
, 2003, “
Optimal Subpixel Interpolation in Particle Image Velocimetry
,”
Exp. Fluids
0723-4864,
35
, pp.
252
256
.
20.
Westerweel
,
J.
, and
Scarano
,
F.
, 2005, “
Universal Outlier Detection for PIV Data
,”
Exp. Fluids
0723-4864,
39
, pp.
1096
1100
.
21.
Schröder
,
A.
, and
Willert
,
C. E.
, 2007, “
Particle Image Velocimetry
,”
Topics in Applied Physics
, Vol.
112
,
J.
Woisetschläger
and
E.
Göttlich
, eds.,
Springer
,
Berlin
.
You do not currently have access to this content.