Control of over-tip leakage flow between turbine blade tips and the stationary shroud is one of the major challenges facing gas turbine designers today. The flow imposes large thermal loads on unshrouded high pressure (HP) turbine blades and is significantly detrimental to turbine blade life. This paper presents results from a computational study performed to investigate the detailed blade tip heat transfer on a sharp-edged, flat tip HP turbine blade. The tip gap is engine representative at 1.5% of the blade chord. Nusselt number distributions on the blade tip surface have been obtained from steady flow simulations and are compared with experimental data carried out in a superscale cascade, which allows detailed flow and heat transfer measurements in stationary and engine representative conditions. Fully structured, multiblock hexahedral meshes were used in the simulations performed in the commercial solver FLUENT. Seven industry-standard turbulence models and a number of different tip gridding strategies are compared, varying in complexity from the one-equation Spalart–Allmaras model to a seven-equation Reynolds stress model. Of the turbulence models examined, the standard $k-ω$ model gave the closest agreement to the experimental data. The discrepancy in Nusselt number observed was just 5%. However, the size of the separation on the pressure side rim was underpredicted, causing the position of reattachment to occur too close to the edge. Other turbulence models tested typically underpredicted Nusselt numbers by around 35%, although locating the position of peak heat flux correctly. The effect of the blade to casing motion was also simulated successfully, qualitatively producing the same changes in secondary flow features as were previously observed experimentally, with associated changes in heat transfer with the blade tip.

1.
Bunker
,
R. S.
, 2001, “
A Review of Turbine Blade Tip Heat Transfer
,”
0077-8923,
934
(
1
), pp.
64
79
.
2.
Mayle
,
R. E.
, and
Metzger
,
D. E.
, 1982, “
Heat Transfer at the Tip of an Unshrouded Turbine Blade
,”
Heat Transfer 1982—Proceedings of the Seventh International Heat Transfer Conference
, München, Federal Republic of Germany, Sept. 6–10,
U.
Grigull
,
E.
Hahne
,
K.
Stephan
, and
J.
Straub
, eds., Vol.
3
, pp.
87
92
.
3.
Yaras
,
M. I.
, and
Sjolander
,
S. A.
, 1992, “
Effects of Simulated Rotation on Tip Leakage in a Planar Cascade of Turbine Blades: Part I—Tip Gap Flow
,”
ASME J. Turbomach.
0889-504X,
114
(
3
), pp.
652
659
.
4.
,
Gm. S.
,
Han
,
J. C.
,
Teng
,
S.
, and
Boyle
,
R. J.
, 2000, “
Heat Transfer and Pressure Distributions on a Gas Turbine Blade Tip
,”
ASME J. Turbomach.
0889-504X,
122
(
4
), pp.
717
724
.
5.
,
Gm. S.
,
Han
,
J. C.
, and
Boyle
,
R. J.
, 2000, “
Heat Transfer and Flow on the Squealer Tip of a Gas Turbine Blade
,”
ASME J. Turbomach.
0889-504X,
122
(
4
), pp.
725
732
.
6.
Kwak
,
J. S.
,
Ahn
,
J.
,
Han
,
J. C.
,
Lee
,
C. P.
,
Bunker
,
R. S.
,
Boyle
,
R.
, and
Gaugler
,
R.
, 2003, “
Heat Transfer Coefficients on the Squealer Tip and Near-Tip Regions of a Gas Turbine Blade With Single or Double Squealer
,” ASME Paper No. GT2003-38907.
7.
Bunker
,
R. S.
,
Bailey
,
J. C.
, and
Ameri
,
A. A.
, 2000, “
Heat Transfer and Flow on the First-Stage Blade Tip of a Power Generation Gas Turbine: Part 1—Experimental Results
,”
ASME J. Turbomach.
0889-504X,
122
(
2
), pp.
263
271
.
8.
Ameri
,
A. A.
, and
Bunker
,
R. S.
, 2000, “
Heat Transfer and Flow on the First-Stage Blade Tip of a Power Generation Gas Turbine: Part 1—Simulation Results
,”
ASME J. Turbomach.
0889-504X,
122
(
2
), pp.
272
277
.
9.
Wilcox
,
D. C.
, 1994, “
Simulation of Transition With a Two-Equation Turbulence Model
,”
AIAA J.
0001-1452,
32
(
2
), pp.
247
255
.
10.
Menter
,
F. R.
, 1993, “
Zonal Two-Equation k-ω Turbulence Models for Aerodynamic Flows
,”
24th Fluid Dynamics, Plasmadynamics, and Lasers Conference
, Orlando, FL, Jul. 6–9, Paper No. AIAA-93-2906.
11.
Yang
,
H.
,
Acharya
,
S.
,
,
S. V.
,
Prakash
,
C.
, and
Bunker
,
R.
, 2002, “
Flow and Heat Transfer Predictions for a Flat-Tip Turbine Blade
,” ASME Paper No. GT2002-30190.
12.
Yang
,
H.
,
Acharya
,
S.
,
,
S. V.
,
Prakash
,
C.
, and
Bunker
,
R.
, 2002, “
Numerical Simulation of Flow and Heat Transfer Past a Turbine Blade With a Squealer-Tip
,” ASME Paper No. GT2002-30193.
13.
Palafox
,
P.
, 2006, “
Gas Turbine Tip Leakage Flow and Heat Transfer
,” DPhil thesis, Oxford University, Oxford, UK.
14.
Palafox
,
P.
,
Oldfield
,
M. L. G.
,
LaGraff
,
J. E.
, and
Jones
,
T. V.
, 2008, “
PIV Maps of Tip Leakage and Secondary Flow Fields on a Low-Speed Turbine Blade Cascade With Moving End Wall
,”
ASME J. Turbomach.
0889-504X,
130
(
1
), p.
011001
.
15.
Palafox
,
P.
,
Oldfield
,
M. L. G.
,
Ireland
,
P. T.
,
Jones
,
T. V.
, and
Lagraff
,
J. E.
, 2006, “
Blade Tip Heat Transfer and Aerodynamics in a Large Scale Turbine Cascade With Moving Endwall
,” ASME Paper No. GT2006-90425.
16.
Moffatt
,
R. J.
, 1982, “
Contributions to the Theory of Single-Sample Uncertainty Analysis
,”
ASME J. Fluids Eng.
0098-2202,
104
, pp.
250
260
.