An experimental and numerical study of the transonic flow through a linear compressor cascade with endwalls was conducted. The cascade with a low aspect ratio of 1.34 was tested at an inlet Mach number of 1.09 and a Reynolds number of 1.9×106. Detailed flow visualizations on the surfaces and five-hole probe measurements inside the blading and in the wake region showed clearly a three-dimensional boundary layer separation on the blade surface and the sidewall, and a severe corner stall induced by a strong 3-D shock system at blade passage entrance. The experimental data have been used to validate and improve the 3-D Navier-Stokes code TRACE. Results showed an excellent resolution of the complex flow field. Surface pressure distributions on the entire blade surface and the endwalls, flow angle and total pressure contours within the blade passage and the wake are compared with the experimental results. An analysis of the secondary flow of this highly staggered cascade did not show the classical corner vortex. Instead, a severe flow deviation and partly reverse flow near the walls is seen. The flow solver helped to identify a weak ring vortex that originates from the passage sidewall. Surface oil flow pictures on the blade contour and the sidewall are in qualitatively good agreement to numerical surface streaklines. A considerable improvement of the numerical results could be achieved by a gradual grid refinement, especially in the corner region and by successive code development.

1.
Weingold
,
H. D.
,
Neubert
,
R. J.
,
Behlke
,
R. F.
, and
Potter
,
G. E.
,
1997
, “
Bowed Stators: An Example of CFD Applied to Improve Multistage Compressor Efficiency
,”
ASME J. Turbomach.
,
119
, pp.
161
168
.
2.
Gu¨mmer, V., Wenger, U., and Kau, H. P., 2001, “Using Sweep and Dihedral to Control Three-Dimensional Flow in Transonic Stators of Axial Compressors,” ASME J. Turbomach., 12, Paper No. 2000-GT-491.
3.
Fottner, L., 1990, “Test Cases for Computation of Internal Flows in Aero Engine Components,” AGARD-AR-275.
4.
Dunham, J., 1998, “CFD Validation for Propulsion System Components,” AGARD-AR-355.
5.
Kang, S., and Hirsch, Ch., 1991, “Three Dimensional Flow in a Linear Compressor Cascade at Design Conditions,” ASME Paper No. 91-GT-114, Orlando, FL.
6.
Osborne
,
D. J.
,
Ng
,
W. F.
, and
Tweedt
,
D. L.
,
1998
, “
Studies of Secondary Flow at Endwall of a Supersonic Compressor Cascade
,”
AIAA J.
,
36
, No.
2
, pp.
128
133
.
7.
Steinert, W., Schreiber, H. A., and Weber, A., 1996, “Experimente am transsonischen Verdichtergitter DLR-TSG-89-5 bei M1=0.90 und M1=1.09,” DLR-IB-325-10-96, DLR Ko¨ln, Germany.
8.
Fuchs, R., Steinert, W., and Starken, H., 1993, “Transonic Compressor Rotor Cascade with Boundary-Layer Separation: Experimental and Theoretical Results,” ASME Paper No. 93-GT-12-405.
9.
Weber, A., and Nicke, E., 1997, “A Study of Sweep on the Performance of a Transonic Cascade with and without Endwall Influence,” Proc., 13th Int. Symp. Air Breathing Engines, ISABE, Chattanooga, TN, Vol. 2, pp. 877-888.
10.
Weber, A., Schreiber, H. A., Fuchs, R., and Steinert, W., 2000, “Ra¨umliche Stro¨mungen in transsonischen Verdichtergittern sehr hoher Belastung,” Abschlußbericht zum HTGT-Turbotech Vorhaben 1.131 der Arbeitsgemeinschaft Hochtemperatur-Gasturbine (AG-Turbo), DLR Ko¨ln, Germany.
11.
Stark, U., and Bross, S., 1996, “Endwall Boundary Layer Separations and Loss Mechanisms in Two Compressor Cascades of Different Stagger Angle,” AGARD-CP-571, Paper No. 1.
12.
Vogel, D. T., 1994, “Navier-Stokes Calculation of Turbine Flows with Film Cooling,” 19th Congress of the International Council of the Aeronautical Sciences, ICAS-94-12-253.
13.
Vogel, D. T., 1999, “A Simulation Package for Turbomachinery Components,” Proc. First ONERA-DLR Aerospace Symposium, Paris, France.
14.
Ku¨geler, E., 2000, “Numerische Untersuchung der Filmku¨hlung aus einer Reihe von Fan-shaped Bohrungen auf der Saugseite einer Turbinenschaufel und Vergleich mit Experimenten,” DGLR Jahrestagung 2000, Leipzig, DGLR-JT2000-139, Bonn, Germany.
15.
Ku¨geler, E., Weber, A., and Lisiewicz, S., 2001, “Combination of a Transition Model with a Two-Equation Turbulence Model and Comparison with Experimental Results,” Proc. 4th European Turbomachinery Conference, Florence, Italy, Paper No. ATI-CST-076/01.
16.
Eulitz, F., Engel, K., Nu¨rnberger, D., Schmitt, S., and Yamamoto, K., 1998, “On Recent Advances of a Parallel Time-Accurate Navier-Stokes Solver for Unsteady Turbomachinery Flow,” Computational Fluid Dynamics ’98, Proc., 4th ECCOMAS, eds., Papailiou et al., Vol. 1, Part 1, pp. 252–258, John Wiley & Sons, New York, NY.
17.
Yamamoto, K., and Engel, K., 1997, “Multiblock Grid Generation Using an Elliptic Differential Equation,” AIAA Paper No. 97-0201, 35th Aerospace Sciences Meeting & Exhibit, Reno, NV.
18.
Hah
,
C.
, and
Loellbach
,
J.
,
1999
, “
Development of Hub Corner Stall and Its Influence on the Performance of Axial Compressor Blade Rows
,”
ASME J. Turbomach.
,
121
, pp.
67
77
.
19.
Schulz, H. D., Gallus, H. E., and Lakshminarayana, B., 1989, “Three-Dimensional Separated Flow Field in the Endwall Region of an Annular Compressor Cascade in the Presence of Rotor-Stator Interaction—Part I: Quasi-Steady Flow Field and Comparison with Steady-State Data,” ASME Paper No. 89-GT-76.
20.
Weber, A., Steinert, W., Fuchs, R., and Schreiber, H. A., 1999, “3D Flow in a Transonic Compressor Cascade (DLR TSG-97),” DLR-IB-325-06-99.
You do not currently have access to this content.