Adiabatic effectiveness and iso-energetic heat transfer coefficients are presented from measurements downstream of film-cooling holes inclined at 30 deg. with respect to the test surface in spanwise/normal planes. With this configuration, holes are spaced 3d apart in the spanwise direction and 4d in the streamwise direction in two staggered rows. Results are presented for an injectant to free-stream density ratio near 1.0, and injection blowing ratios from 0.5 to 1.5. Spanwise-averaged adiabatic effectiveness values downstream of the spanwise/normal plane holes are significantly higher than values measured downstream of simple angle holes for x/d < 25–70(depending on blowing ratio) when compared for the same normalized streamwise location, blowing ratio, and spanwise and streamwise hole spacings. Spanwise-averaged iso-energetic Stanton number ratios range between 1.0 and 1.41, increase with blowing ratio at each streamwise station, and show little variation with streamwise location for each value of blowing ratio tested.

1.
Goldstein
R. J.
,
Eckert
E. R. G.
,
Eriksen
V. L.
, and
Ramsey
J. W.
,
1970
, “
Film Cooling Following Injection Through Inclined Circular Tubes
,”
Israel Journal of Technology
, Vol.
8
, pp.
145
154
.
2.
Honami, S., and Fukagawa, M., 1987, “A Study on Film Cooling Behavior of a Cooling Jet Over a Concave Surface,” Paper No. 87-Tokyo IGTC-72, Proc. 1987 Tokyo International Gas Turbine Congress, Vol. 3, pp. 209–216.
3.
Honami
S.
,
Shizawa
T.
, and
Uchiyama
A.
,
1994
, “
Behavior of the Laterally Injected Jet in Film Cooling: Measurements of Surface Temperature and Velocity/Temperature Field Within the Jet
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
116
, pp.
106
112
.
4.
Kim, H. K., Moffat, R. J., and Kays, W. M., 1978, “Heat Transfer to a Full-Coverage, Film-Cooled Surface With Compound-Angle (30° and 45°) Hole Injection,” Report No. HMT-28, Thermosciences Division, Department of Mechanical Engineering, Stanford University, Stanford, CA.
5.
Kline, S. J., and McClintock, F. A., 1953, “Describing Uncertainties in Single-Sample Experiments,” Mechanical Engineering, Jan., pp. 3–8.
6.
Ligrani
P. M.
,
Ciriello
S.
, and
Bishop
D. T.
,
1992
, “
Heat Transfer, Adiabatic Effectiveness, and Injectant Distributions Downstream of a Single Row and Two Staggered Rows of Compound Angle Film-Cooling Holes
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
114
, pp.
687
700
.
7.
Ligrani
P. M.
,
Wigle
J. M.
,
Ciriello
S.
, and
Jackson
S. W.
,
1994
a, “
Film-Cooling From Holes With Compound Angle Orientations: Part 1—Results Downstream of Two Staggered Rows of Holes With 3d Spanwise Spacing
,”
ASME Journal of Heat Transfer
, Vol.
116
, pp.
341
352
.
8.
Ligrani
P. M.
,
Wigle
J. M.
, and
Jackson
S. W.
,
1994
b, “
Film-Cooling From Holes With Compound Angle Orientations: Part 2—Results Downstream of a Single Row of Holes With 6d Spanwise Spacing
,”
ASME Journal of Heat Transfer
, Vol.
116
, pp.
353
362
.
9.
Ligrani, P. M., and Ramsey, A. E., 1995, “Film Cooling From Spanwise Oriented Holes in Two Staggered Rows,” ASME Paper No. 95-GT-39.
10.
Ligrani, P. M., and Ramsey, A. E., 1997, “Film Cooling From a Single Row of Holes Oriented in Spanwise/Normal Planes,” ASME JOURNAL OF TURBOMACHINERY, to appear.
11.
Mayle
R. E.
, and
Camarata
F. J.
,
1975
, “
Multihole Cooling Film Effectiveness and Heat Transfer
,”
ASME Journal of Heat Transfer
, Vol.
97
, pp.
534
538
.
12.
Moffat
R. J.
,
1982
, “
Contributions to the Theory of Single-Sample Uncertainty Analysis
,”
ASME Journal of Fluids Engineering
, Vol.
104
, pp.
250
260
.
13.
Ramsey, A. E., 1992, “A Study of Film Cooling Downstream of One and Two Rows of Holes Oriented in Spanwise/Normal Planes,” M. S. Thesis, Department of Mechanical Engineering, Naval Postgraduate School, Monterey, CA.
14.
Sathyamurthy
P.
, and
Patankar
S. V.
,
1990
, “
Prediction of Film Cooling With Lateral Injection
,”
Heat Transfer in Turbulent Flows
, ASME-HTD Vol.
138
, pp.
61
70
.
15.
Schmidt
D. L.
,
Sen
B.
, and
Bogard
D. G.
,
1996
, “
Film Cooling With Compound Angle Holes: Adiabatic Effectiveness
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
118
, pp.
807
813
.
16.
Sen
B.
,
Schmidt
D. L.
, and
Bogard
D. G.
,
1996
, “
Film Cooling With Compound Angle Holes: Heat Transfer
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
118
, pp.
800
806
.
17.
Wigle, J. M., 1991, “Heat Transfer, Adiabatic Effectiveness and Injectant Distributions Downstream of Single and Double Rows of Film Cooling Holes With Compound Angles,” M. S. Thesis, Department of Mechanical Engineering, Naval Postgraduate School, Monterey, CA.
This content is only available via PDF.
You do not currently have access to this content.