In this paper, a one-dimensional unsteady compressible viscous flow model of a generic compression system previously developed by the authors is applied to a multistage axial compressor experimental rig configured for single-stage operation. The required model parameters and maps are identified from experimental data. The resulting model is an explicit system of nine first-order ODEs. The model inputs are compressor speed, nozzle area, compressor discharge bleed area, plenum bleed area, inlet total pressure and entropy, and nozzle and bleed exit static pressures. The model and experimental data are compared with respect to both open-loop uncontrolled and closed-loop controlled behaviors. These comparisons focus on (i) forced transients and (ii) global nonlinear dynamics and bifurcations. In all cases the agreement between the model and experimental data is excellent. Of particular interest is the ability of the model, which does not include any hysteretic maps, to predict experimentally observed hysteresis with respect to the onset and cessation of surge. This predictive capability of the model manifests itself as the coexistence of a stable equilibrium (rotating stall) and a stable periodic solution (surge) in the model at a single fixed set of system input values. Also of interest is the fact that the controllers used for closed-loop comparisons were designed directly from the model with no a posteriori tuning of controller parameters. Thus, the excellent closed-loop comparisons between the model and experimental data provide strong evidence in support of the validity of the model for use in direct model based controller design. The excellent agreement between the model and experimental data summarized above is attributed in large part to the use of effective lengths within the model, as functions of axial Mach number and nondimensional compressor rotational speed, as prescribed by the modeling technique. The use of these effective lengths proved to be far superior to the use of physical lengths. The use of these effective lengths also provided substantial improvement over the use of physical lengths coupled with fixed first-order empirical lags, as proposed by other authors for the modeling of observed compressor dynamic lag. The overall success of this model is believed to represent a positive first step toward a complete experimental validation of the approach to control-oriented high-frequency turbomachinery modeling being developed by the authors.

1.
Badmus, O. O., Eveker, K. M., and Nett, C. N., “Control-Oriented High-Frequency Turbomachinery Modeling, Part 1: Theoretical Foundations,” in: Proceedings of the 1992 AIAA Joint Propulsion Conference, July 1992, AIAA Paper No. 92-3314.
2.
Badmus, O. O., Eveker, K. M., and Nett, C. N., “Control-Oriented High-Frequency Turbomachinery Modeling: Theoretical Foundations,” submitted for publication to the ASME JOURNAL OF TURBOMACHINERY, 1993.
3.
Badmus, O. O., Eveker, K. M., and Nett, C. N., “Control-Oriented High-Frequency Turbomachinery Modeling: General ID Model Development,” ASME Paper No. 93-GT-385, 1993; accepted for publication in the JOURNAL OF TURBOMACHINERY.
4.
Nett, C. N., “LICCHUS Experimental Facilities Summary: September 1992 (Months 1–18),” Oct. 1991; Videotape presentation, available from School of Aerospace Engineering, Georgia Tech, 120 min.
5.
Mees
A. I.
, “
A Plain Man’s Guide to Bifurcations
,”
IEEE Transactions on Circuits and Systems
, Vol.
CAS-30
, No.
8
,
1983
, pp.
512
517
.
6.
Greitzer
E. M.
, “
Surge and Rotating Stall in Axial Flow Compressors, Part 1: Theoretical Compression System Model
,”
ASME Journal of Engineering for Power
, Vol.
98
,
1976
, pp.
190
198
.
7.
Davis, M. W., and O’Brien, W. F., “A Stage-by-Stage Post-Stall Compression System Modeling Technique,” AIAA Paper No. 87-2088, 1987.
8.
Ffowcs-Williams
J. E.
, and
Huang
X. Y.
, “
Active Stabilization of Compressor Surge
,”
J. Fluid Mech.
, Vol.
204
,
1989
, pp.
245
262
.
9.
Sugiyama
Y.
,
Tabakoff
W.
, and
Hamed
A.
, “
J85 Surge Transient Simulation
,”
J. Propulsion and Power
, Vol.
5
,
1989
, pp.
375
381
.
10.
Tang, G. C., “Basic Features of Speed Induced Transient Behaviour of Axial Flow Compressors,” ASME Paper No. 90-GT-211, 1990.
11.
Davis, M., “Parametric Investigation Into the Combined Effects of Pressure and Temperature Distortion on Compression System Stability,” in: AIAA/SAE/ASME/ASEE Joint Propulsion Conference, June 1991, Paper No. AIAA-91-1895.
12.
Greitzer
E. M.
, “
Surge and Rotating Stall in Axial Flow Compressors, Part 2: Experimental Results and Comparison with Theory
,”
ASME Journal of Engineering for Gas Turbines and Power
, Vol.
98
,
1976
, pp.
199
217
.
13.
Stenning
A. H.
, “
Rotating Stall and Surge
,”
ASME Journal of Fluids Engineering
, Vol.
102
,
1980
, pp.
14
21
.
14.
Fasol
K. H.
, “
Recent Experiences with Modelling and Simulation of Some Industrial Plants
,”
Israel J. Technology
, Vol.
17
,
1979
, pp.
207
216
.
15.
Macdougal
I.
, and
Elder
R. L.
, “
Simulation of Centrifugal Compressor Transient Performance for Process Plant Applications
,”
ASME Journal of Engineering for Gas Turbines and Power
, Vol.
105
,
1983
, pp.
885
890
.
16.
Wenzel, L. M., and Bruton, W. M., “Analytical Investigation of Nonrecoverable Stall,” Technical Memorandum 82792, NASA, Feb. 1982.
17.
Hosny, W. M., Bitter, S. J., and Steenken, W. G., “Turbofan Engine Nonrecoverable Stall Computer-Simulation Development and Validation,” AIAA Paper No. 85-1432, 1985.
18.
Chung, K., Leamy, K. R., and Collins, T. P., “A Turbine Engine Aerodynamic Model for In-Stall Transient Simulation,” in: 21st Joint Propulsion Conference, July 1985, AIAA Paper No. 85-1429.
19.
Steenken, W. G., “Turbofan Engine Post-Instability Behavior: Computer Simulations, Test Validation, and Application of Simulations,” in: Engine Response to Distorted Inlet Flow Conditions, AGARD-CP-400, 1987.
20.
Epstein
A. H.
,
Ffowcs-Williams
J. E.
, and
Greitzer
E. M.
, “
Active Suppression of Aerodynamic Instabilities of Turbomachines
,”
J. Propulsion and Power
, Vol.
5
,
1989
, pp.
204
211
.
21.
Ffowcs-Williams, J. E., and Graham, W. R., “Engine Demonstration of Active Surge Control,” in: Proceedings of the 1990 ASME International Gas Turbine and Aeroengine Congress and Exposition, 1990.
22.
Gysling, D. L., Dugundji, J., Epstein, A. H., and Greitzer, E. M., “Dynamic Control of Centrifugal Compressor Surge Using Tailored Structures,” in: Proceedings of the 1990 ASME Gas Turbine Conference, 1990.
23.
Pinsley, J. E., Guenette, G. R., Epstein, A. H., and Greitzer, E. M., “Active Stabilization of Centrifugal Compressor Surge,” in: Proceedings of the 1990 ASME Gas Turbine Conference, 1990.
24.
Hosny, W. M., Leventhal, L., and Steenken, W. G., “Active Stabilization of Multistage Axial-Compressor Aerodynamic System Instabilities,” ASME Paper No. 91-GT-403, 1991.
25.
Badmus, O. O., Nett, C. N., and Schork, F. J., “An Integrated Full-Range Surge Control/Rotating Stall Avoidance Compressor Control System,” in: Proceedings of the 1991 American Control Conference, 1991.
26.
Day, I. J., “Active Suppression of Rotating Stall and Surge in Axial Compressors,” ASME Paper No. 91-GT-87, 1991.
27.
Moore
F. K.
, “
A Theory of Rotating Stall of Multistage Compressors, Parts I–III
,”
ASME Journal of Engineering for Gas Turbines and Power
, Vol.
106
,
1984
, pp.
313
336
.
28.
Moore
F. K.
, and
Greitzer
E. M.
, “
A Theory of Post-Stall Transients in Axial Compression Systems: Part 1, Development of Equations and Part 2, Application
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
108
,
1986
, pp.
68
76
.
29.
Moore
F. K.
, “
Stall Transients of Axial Compression Systems With Inlet Distortion
,”
J. Propulsion and Power
, Vol.
2
,
1986
, pp.
552
561
.
30.
Paduano, J., Valavani, L., Epstein, A. H., Greitzer, E. M., and Guenette, G., “Modeling for Control of Rotating Stall,” Proceedings 29th IEEE Conference on Decision and Control, 1991.
31.
Paduano, J., “Active Control of Rotating Stall in Axial Compressor,” PhD thesis, Massachusetts Institute of Technology, 1991.
32.
Bonnaure, L., “Modelling High Speed Multistage Compressor Stability,” Master’s thesis, Department of Aeronautics and Astronautics, Massachusetts Institute of Technology, 1991.
33.
Dugundji, J., Garnier, V. H., Epstein, A. H., Greitzer, E. M., Guenette, G., Paduano, J., Silkowski, P., Simon, J., and Valavani, L., “A Progress Report on Active Control of Flow Instabilities: Rotating Stall Stabilization in Axial Compressors,” in: Proceedings of the 1989 AIAA 2nd Shear Flow Conference, Mar. 1989, AIAA Paper No. 89-1008.
34.
Simon, J. S., and Valavani, L., “A Lyapunov Based Nonlinear Control Scheme for Stabilizing a Basic Compression System Using a Close-Coupled Valve,” in: Proceedings of the 1991 American Control Conference, 1991.
35.
Liaw, D. C., and Abed, E. H., “Stability Analysis and Control of Rotating Stall,” in: Proceedings of the 2nd IFAC Nonlinear Control Systems Design Symposium, June 1992.
36.
Greitzer
E. M.
, “
Review—Axial Compressor Stall Phenomena
,”
ASME Journal of Fluids Engineering
, Vol.
102
,
1980
, pp.
134
151
.
37.
McCaughan
F. E.
, “
Application of Bifurcation Theory to Axial Flow Compressor Instability
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
111
,
1989
, pp.
426
433
.
38.
McCaughan
F. E.
, “
Numerical Results for Axial Flow Compressor Instability
,”
ASME JOURNAL OF TURBOMACHINERY
, Vol.
111
,
1989
, pp.
434
441
.
39.
Abed, E. H., Houpt, P. K., and Hosny, W. M., “Bifurcation Analysis of Surge and Rotating Stall in Axial Flow Compressors,” in: Proceedings of the 1990 American Control Conference, May 1990.
40.
McCaughan
F. E.
, “
Bifurcation Analysis of Axial Flow Compressor Stability
,”
SIAM Journal of Applied Math.
, Vol.
50
,
1990
, pp.
1232
1253
.
41.
Liaw, D. C., Adomaitis, R. A., and Abed, E. H., “Two-Parameter Bifurcation Analysis of Axial Flow Compressor Dynamics,” Proceedings of the American Control Conference, pp. 2955–2960, 1991, IEEE Cat. No. 91CH2939-7.
42.
Oliva, S. M., and Nett, C. N., “A General Nonlinear Dynamic Analysis of Second-Order, One-Dimensional, Theoretical Compression System Model,” in: Proceedings of the 1991 American Control Conference, 1991.
43.
Abed, E. H., and Liaw, D., “Two-Parameter Bifurcation Analysis of Axial Flow Compressor Dynamics,” in Proceedings of the 1991 American Control Conference, 1991.
44.
Thompson, J. W., and Abernathy, R. B., “Handbook of Uncertainty in Gas Turbine Measurements,” Tech. Rep., AEDC, Feb. 1973, AEDC-TR-73-5.
45.
Badmus, O. O., Chowdhury, S., Davis, E. J., Eveker, K. M., and Nett, C. N., “Single-Stage Compression System ID Model,” 1993, LICCHUS Internal Report No. 93-001.
46.
Hindmarsh, A. C., “ODEPACK, A Systematized Collection of ODE Solvers,” in: Scientific Computing: Applications of Mathematics and Computing to the Physical Sciences, R. S. Stepleman, ed., North-Holland, 1983, pp. 55–64.
47.
Mees, A. I., Dynamics of Feedback Systems, John Wiley & Sons, 1981.
48.
de Boor, C., A Practical Guide to Splines, Springer-Verlag, 1978.
49.
Doedel
E.
, “
AUTO: A Program for the Automatic Bifurcation Analysis of Autonomous Systems
,”
Cong. Num.
, Vol.
30
,
1981
, pp.
265
284
.
50.
Genesio
R.
,
Tartaglia
M.
, and
Vicino
A.
, “
On the Estimation of Asymptotic Stability Regions: State of The Art and New Proposals
,”
IEEE Transactions of Automatic Control
, Vol.
30
,
1985
, pp.
747
755
.
51.
Maciejowski, J. M., Multivariable Feedback Design, Addison-Wesley, 1989.
52.
The MathWorks, Inc., South Natick, MA, MATLAB Reference Manual, 1990.
53.
Glover, K., Sefton, J., and Mcfarlane, D., “A Tutorial on Loop Shaping Using h-Infinity Robust Stabilization,” Robust Control, 1990, pp. 117–126.
This content is only available via PDF.
You do not currently have access to this content.