The unshrouded impeller and the vaneless diffuser of a single-stage radial compressor have been investigated at three flow rates. Three-dimensional velocities and pressures were measured at a tip speed of 84 m/s by an L2F-velocimeter, a slanted single hotwire probe, and piezoresistive pressure transducers. The measurements show that upstream of the blading the averaged meridional inlet flow angle is about 54 deg and a periodic variation of the meridional flow angle of about 25 deg occurs near the casing wall. Further, an inlet vortex in the clockwise direction appears and an initial whirl is induced. The specific work of the initial whirl corresponds to approximately 12 percent of the enthalpy losses between inlet pipe and diffuser outlet. In the beginning of the passage, the inlet vortex is suppressed and a solid body vortex in the counterclockwise direction can be observed. At the outlet, a heavy flow deceleration at the blade suction side with subsequent separation can be seen. Increasing the flow rate decreases the wake and causes a more uniform loss distribution in this area. The measured secondary vortex flow and rotary stagnation pressure gradients are compared with test results from impellers with inducer. The incidence of the investigated impeller is greater than that of the impellers with inducer, but the wake-jet outlet flows are very similar. Inlet losses could be reduced by improving incidence angles by matching the blade angles to the inlet flow angles. Smaller blade angles at the shroud would reduce or eliminate separation at the leading edge, and the resulting reduction in low-momentum fluid along the suction surface would help to avoid separation on that surface near the outlet.
Skip Nav Destination
Sign In or Register for Account
Article navigation
October 1991
Research Papers
Secondary Flow and Loss Distribution in a Radial Compressor With Untwisted Backswept Vanes
G. Sipos
G. Sipos
Institute of Thermal Turbomachines and Power Plants, Technical University of Vienna, Vienna, Austria
Search for other works by this author on:
G. Sipos
Institute of Thermal Turbomachines and Power Plants, Technical University of Vienna, Vienna, Austria
J. Turbomach. Oct 1991, 113(4): 686-695 (10 pages)
Published Online: October 1, 1991
Article history
Received:
January 15, 1990
Online:
June 9, 2008
Citation
Sipos, G. (October 1, 1991). "Secondary Flow and Loss Distribution in a Radial Compressor With Untwisted Backswept Vanes." ASME. J. Turbomach. October 1991; 113(4): 686–695. https://doi.org/10.1115/1.2929135
Download citation file:
Sign In
Get Email Alerts
Cited By
Upstream Film Cooling on the Contoured Endwall of a Transonic Turbine Vane in an Annular Cascade
J. Turbomach (June 2021)
Design of a Tip Appendage for the Control of Tip Leakage Vortices in Axial Flow Fans
J. Turbomach (July 2021)
An Additively Manufactured Four-Sensor Fast Response Aerodynamic Probe
J. Turbomach (July 2021)
Assessment of MULTALL as Computational Fluid Dynamics Code for the Analysis of Tube-Axial Fans
J. Turbomach (July 2021)
Related Articles
Clearance Effects on the Evolution of the Flow in the Vaneless Diffuser of a Centrifugal Compressor at Part Load Condition
J. Turbomach (July,2008)
A Distinction Between Different Types of Stall in a Centrifugal Compressor Stage
J. Eng. Gas Turbines Power (January,1986)
A Numerical Investigation on the Volute/Diffuser Interaction Due to the Axial Distortion at the Impeller Exit
J. Fluids Eng (September,2001)
Deterministic Blade Row Interactions in a Centrifugal Compressor Stage
J. Turbomach (April,1992)
Related Proceedings Papers
Related Chapters
Introduction
Design and Analysis of Centrifugal Compressors
Other Components and Variations
Axial-Flow Compressors
The Special Characteristics of Closed-Cycle Gas Turbines
Closed-Cycle Gas Turbines: Operating Experience and Future Potential