Abstract

Sequential honing process is usually implemented in engine cylinder bore processing to obtain the cross-hatched surface texture with excellent function to balance lubricant storage capacities and supporting performance. Many researches have devoted to correlating honed surface quality of cylinder bore with honing process parameters by means of experiments or simulations. Quite a few efforts have addressed the effect of sequential multiple steps on the surface texture in the honing of engine cylinder bore. However, these researches cannot provide an explicit and analytical methodology to predict honed surface texture efficiently and accurately. This paper presents an analytical and explicit methodology to incorporate a proposed microscale abrasive model into the analytical simulation process of sequential honing. The proposed abrasive model synthetically considers the shape, size, posture, and position of abrasives randomly distributed in honing stone, which is incorporated into honing head motions in terms of rotation, oscillation, and feeding. The kinematics of honing head is calculated by space–time discretization to capture the interaction between honing stones and cylinder bore surface. The above procedure acts as each single step for the sequential honing processes. This study investigates the sequential honing of two stages including semi-finish honing and plateau honing at different feeding speeds by applying the abrasive model with different abrasive sizes. The formation of cross-hatched surface texture was successfully achieved sequentially by semi-finish honing and plateaus honing. Then, the Abbott-Firestone curve of the honed surface can be obtained to analyze the influences of abrasive size and honing time of two stages on the surface roughness. Correctness of surface roughness predicted by the model is verified by comparing with a group of experiment measurements in terms of Abbott-Firestone Curve. Most errors of all the predicted Rk roughness family roughness parameters in the two honing stages are less than 15%. Based on the model, simulations are done to analyze the influences of abrasive size and honing duration time of two stages on the surface roughness. The result shows that the larger abrasive used in finish honing leads to the decrease in the material portions Mr1, Mr2 and the increase in the reduced valley depth Rvk. The longer plateau honing duration time is preferred to produce the larger Mr1, Mr2, and the smaller Rvk.

References

References
1.
Biboulet
,
N.
,
Bouassida
,
H.
, and
Lubrecht
,
A.
,
2015
, “
Cross Hatched Texture Influence on the Load Carrying Capacity of Oil Control Rings
,”
Tribol. Int.
,
82
(
Part A
), pp.
12
19
. 10.1016/j.triboint.2014.09.024
2.
Lawrence
,
K.
, and
Ramamoorthy
,
B.
,
2016
, “
Multi-Surface Topography Targeted Plateau Honing for the Processing of Cylinder Liner Surfaces of Automotive Engines
,”
Appl. Surf. Sci.
,
365
(
3
), pp.
19
30
. 10.1016/j.apsusc.2015.12.245
3.
Pawlus
,
P.
,
1993
, “
Effects of Honed Cylinder Surface Topography on the Wear of Piston-Piston Ring-Cylinder Assemblies Under Artificially Increased Dustiness Conditions
,”
Tribol. Int.
,
26
(
1
), pp.
49
55
. 10.1016/0301-679X(93)90038-3
4.
Michail
,
S.
, and
Barber
,
G.
,
1995
, “
The Effects of Roughness on Piston Ring Lubrication Part I: Model Development
,”
Tribol. Trans.
,
38
(
1
), pp.
19
26
. 10.1080/10402009508983375
5.
Sabri
,
L.
,
Mezghani
,
S.
,
El Mansori
,
M.
, and
Zahouani
,
H.
,
2011
, “
Multiscale Study of Finish-Honing Process in Mass Production of Cylinder Liner
,”
Wear
,
271
(
3–4
), pp.
509
513
. 10.1016/j.wear.2010.03.026
6.
Reizer
,
R.
, and
Pawlus
,
P.
,
2012
,
“Modelling of Plateau Honed Cylinder Surface Topography
,”
Proc. Inst. Mech. Eng., Part B: J. Eng. Manuf.
,
226
(
9
), pp.
1564
1578
. 10.1177/0954405412452238
7.
Malburg
,
M.
,
Raja
,
J.
, and
Whitehouse
,
D.
,
1993
, “
Characterization of Surface Texture Generated by Plateau Honing Process
,”
CIRP Ann.
,
42
(
1
), pp.
637
639
. 10.1016/S0007-8506(07)62527-X
8.
Pawlus
,
P.
,
Cieslak
,
T.
, and
Mathia
,
T.
,
2009
, “
The Study of Cylinder Liner Plateau Honing Process
,”
J. Mater. Process. Technol.
,
209
(
20
), pp.
6078
6086
. 10.1016/j.jmatprotec.2009.04.025
9.
Sivatte-Adroer
,
M.
,
Llanas-Parra
,
X.
,
Buj-Corral
,
I.
, and
Vivancos-Calvet
,
J.
,
2016
, “
Indirect Model for Roughness in Rough Honing Processes Based on Artificial Neural Networks
,”
Precis. Eng.
,
43
(
1
), pp.
505
513
. 10.1016/j.precisioneng.2015.09.004
10.
Feng
,
C. X.
,
Wang
,
X. F.
, and
Yu
,
Z. G.
,
2002
, “
Neural Networks Modeling of Honing Surface Roughness Parameters Defined by ISO 13565
,”
J. Manuf. Syst.
,
21
(
5
), pp.
395
408
. 10.1016/S0278-6125(02)80037-1
11.
Lee
,
J.
, and
Malkin
,
S.
,
1993
, “
Experimental Investigation of the Bore Honing Process
,”
ASME J. Eng. Ind.
,
115
(
4
), pp.
406
414
. 10.1115/1.2901783
12.
Buj Corral
,
I.
,
Calvet
,
J.
, and
Salcedo
,
M.
,
2010
, “
Use of Roughness Probability Parameters to Quantify the Material Removed in Plateau-Honing
,”
Int. J. Mach. Tools Manuf.
,
50
(
7
), pp.
621
629
. 10.1016/j.ijmachtools.2010.02.007
13.
Ding
,
W. F.
,
Xu
,
J. H.
,
Chen
,
Z. Z.
,
Su
,
H. H.
, and
Fu
,
Y. C.
,
2010
, “
Wear Behavior and Mechanism of Single-Layer Brazed CBN Abrasive Wheels During Creep-Feed Grinding Cast Nickel-Based Superalloy
,”
Int. J. Adv. Manuf. Technol.
,
51
(
5–8
), pp.
541
550
. 10.1007/s00170-010-2643-1
14.
Yan
,
L.
,
Jiang
,
F.
, and
Fang
,
C. F.
,
2014
, “
Research on Material Removal Mechanism of Single Grit Cutting Based on FEM Simulation
,”
Adv. Mater. Res.
,
1017
(
Advances in Abrasive Technology XVII
), pp.
82
87
. www.scientific.net/AMR.1017.82
15.
Dai
,
C. W.
,
Ding
,
W. F.
,
Xu
,
J. H.
,
Fu
,
Y. C.
, and
Yu
,
T. Y.
,
2017
, “
Influence of Grain Wear on Material Removal Behavior During Grinding Nickel-Based Superalloy With a Single Diamond Grain
,”
Int. J. Mach. Tools Manuf.
,
113
(
2
), pp.
49
58
. 10.1016/j.ijmachtools.2016.12.001
16.
Joliet
,
R.
,
Kansteiner
,
M.
, and
Kersting
,
P.
,
2015
, “
A Process Model for Force-Controlled Honing Simulations
,”
Procedia CIRP
,
28
(
3rd CIRP Global Web Conference-Production Engineering Research
), pp.
46
51
. 10.1016/j.procir.2015.04.009
17.
Kersting
,
P.
,
Joliet
,
R.
, and
Kansteiner
,
M.
,
2015
, “
Modeling and Simulative Analysis of the Micro-Finishing Process
,”
CIRP Ann.
,
64
(
1
), pp.
321
324
. 10.1016/j.cirp.2015.04.014
18.
Goeldel
,
B.
,
Mansori
,
M.
, and
Dumur
,
D.
,
2013
, “
Simulation of Roughness and Surface Texture Evolution at Macroscopic Scale During Cylinder Honing Process
,”
Procedia CIRP
,
8
(
14th CIRP Conference on Modeling of Machining Operations
), pp.
27
32
. 10.1016/j.procir.2013.06.060
19.
Ueda
,
T.
, and
Yamamoto
,
A.
,
1984
, “
An Analytical Investigation of the Honing Mechanism
,”
ASME J. Eng. Ind.
,
106
(
3
), pp.
237
241
. 10.1115/1.3185940
20.
Feng
,
Q.
,
Ren
,
C. Z.
, and
Pei
,
Z. J.
,
2015
, “
A Physics-Based Predictive Model for Number of Contact Grains and Grain Depth of Cut in Honing
,”
Mach. Sci. Technol.
,
19
(
1
), pp.
50
70
. 10.1080/10910344.2014.991024
21.
Rom
,
M.
,
Brakhage
,
K.
,
Barth
,
S.
,
Wrobel
,
C.
,
Mattfeld
,
P.
, and
Klocke
,
F.
,
2018
, “
Mathematical Modeling of Ceramic Bond Bridges in Grinding Wheels
,”
Math. Comput. Simul.
,
147
(
5
), pp.
220
236
. 10.1016/j.matcom.2017.02.002
22.
Aurich
,
J.
, and
Kirsch
,
B.
,
2012
, “
Kinematic Simulation of High-Performance Grinding for Analysis of Chip Parameters of Single Grains
,”
CIRP J. Manuf. Sci. Technol.
,
5
(
3
), pp.
164
174
. 10.1016/j.cirpj.2012.07.004
23.
Weule
,
H.
, and
Eversheim
,
M.
,
1988
, “
Improved Honing Through Process-Control
,”
CIRP Ann.
,
37
(
1
), pp.
339
342
. 10.1016/S0007-8506(07)61649-7
24.
Shaw
,
M.
,
1996
,
Principles of Abrasive Processing
,
Oxford University Press
,
New York
.
25.
Sabri
,
L.
,
Mezghani
,
S.
, and
El Mansori
,
M.
,
2010
, “
A Study on the Influence of Bond Material on Honing Engine Cylinder Bores With Coated Diamond Stones
,”
Surf. Coat. Technol.
,
205
(
5
), pp.
1515
1519
. 10.1016/j.surfcoat.2010.10.016
26.
Sabri
,
L.
, and
El Mansori
,
M.
,
2009
, “
Process Variability in Honing of Cylinder Liner With Vitrified Bonded Diamond Tools
,”
Surf. Coat. Technol.
,
204
(
6–7
), pp.
1046
1050
. 10.1016/j.surfcoat.2009.05.013
27.
Zhou
,
X.
, and
Xi
,
F.
,
2002
, “
Modeling and Predicting Surface Roughness of the Grinding Process
,”
Int. J. Mach. Tools Manuf.
,
42
(
8
), pp.
969
977
. 10.1016/S0890-6955(02)00011-1
28.
Bridson
,
R.
,
2007
, “
Fast Poisson Disk Sampling in Arbitrary Dimensions
,”
Proceeding of ACM SIGGRAPH Sketches
,
San Diego, CA
,
Aug. 5–9
, p.
22
.
29.
Wen
,
X. N.
,
2014
, “
Modeling and Predicting Surface Roughness for the Grinding Process
,”
Appl. Mech. Mater.
,
599–601
(
8
), pp.
622
625
. www.scientific.net/amm.599-601.622
30.
Zhou
,
Z. Y.
,
Zhang
,
X. P.
,
Yao
,
Z. Q.
, and
Xi
,
L. F.
,
2017
, “
Predicting Multi-Scale Dimensional Accuracy of Engine Cylinder by Honing
,”
ASME International Manufacturing Science and Engineering Conference
,
Los Angles, CA
,
June 4–8
, Vol.
1
, p.
V001T02A023
.
31.
ISO
,
1997
, Geometrical Product Specifications—Surface Texture: Profile Method-Surfaces Having Stratified Functional Properties—Part 2: Height Characterization Using the Linear Material Ratio Curve (ISO 13565-2: 1996), German Version EN ISO. 13565.
32.
Buj-Corral
,
I.
, and
Vivancos-Calvet
,
J.
,
2011
, “
Roughness Variability in the Honing Process of Steel Cylinders With CBN Metal Bonded Tools
,”
Precis. Eng.
,
35
(
2
), pp.
289
293
. 10.1016/j.precisioneng.2010.11.004
You do not currently have access to this content.