Instead of a general consideration of the fractal dimension and the topothesy as two invariants in the fractal analysis of surface asperities, these two roughness parameters in the present study are varied by changing the mean separation of two contact surfaces. The relationship between the fractal dimension and the mean separation is found first. By equating the structure functions developed in two different ways, the relationship among the scaling coefficient in the power spectrum function, the fractal dimension, and topothesy of asperity heights can be established. The variation of topothesy can be determined when the fractal dimension and the scaling coefficient have been obtained from the experimental results of the number of contact spots and the power spectrum function at different mean separations. A numerical scheme is developed in this study to determine the convergent values of fractal dimension and topothesy corresponding to a given mean separation. The theoretical results of the contact spot number predicted by the present model show good agreement with the reported experimental results. Both the fractal dimension and the topothesy are elevated by increasing the mean separation. Significant differences in the contact load or the total contact area are shown between the models of constant and and variable and as the mean separation is reduced to smaller values.
Skip Nav Destination
e-mail: jflin@mail.ncku.edu.tw
Article navigation
July 2006
Research Papers
A New Method Developed for Fractal Dimension and Topothesy Varying With the Mean Separation of Two Contact Surfaces
Jeng Luen Liou,
Jeng Luen Liou
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan City, 70101, Taiwan, ROC
Search for other works by this author on:
Jen Fin Lin
Jen Fin Lin
Professor
Department of Mechanical Engineering,
e-mail: jflin@mail.ncku.edu.tw
National Cheng Kung University
, Tainan City, 70101, Taiwan, ROC
Search for other works by this author on:
Jeng Luen Liou
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan City, 70101, Taiwan, ROC
Jen Fin Lin
Professor
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan City, 70101, Taiwan, ROCe-mail: jflin@mail.ncku.edu.tw
J. Tribol. Jul 2006, 128(3): 515-524 (10 pages)
Published Online: March 3, 2006
Article history
Received:
August 31, 2005
Revised:
March 3, 2006
Citation
Liou, J. L., and Lin, J. F. (March 3, 2006). "A New Method Developed for Fractal Dimension and Topothesy Varying With the Mean Separation of Two Contact Surfaces." ASME. J. Tribol. July 2006; 128(3): 515–524. https://doi.org/10.1115/1.2197839
Download citation file:
Get Email Alerts
Related Articles
Variation in Fractal Properties and Non-Gaussian Distributions of Microcontact Between Elastic-Plastic Rough Surfaces With Mean Surface Separation
J. Appl. Mech (January,2006)
Fractal Model Developed for Elliptic Elastic-Plastic Asperity Microcontacts of Rough Surfaces
J. Tribol (October,2004)
A New Microcontact Model Developed for Variable Fractal Dimension, Topothesy, Density of Asperity, and Probability Density Function of Asperity Heights
J. Appl. Mech (July,2007)
Coefficients of Restitution Based on a Fractal Surface Model
J. Appl. Mech (May,2003)
Related Proceedings Papers
Related Chapters
Assessment of CT-Measured Porosity in Russian Soils Using Fractal Dimension and Lacunarity
Intelligent Engineering Systems through Artificial Neural Networks
Evaluation of Rock Mass Quality by Single Fractal Dimension and Mutifractal Spectrum
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)
Application of Adaptive Grayscale Morphological Operators for Image Analysis
Intelligent Engineering Systems through Artificial Neural Networks Volume 18