In this paper we report the experimental investigation to evaluate the published models for the contact of a deformable sphere against a hard flat in the fully plastic contact regime. A new measurement method has been used to measure the contact area. The behavior of the mean contact pressure and the contact area as a function of the contact load are presented. Substantial differences are found between the measurements and the model predictions. A constant value of the mean contact pressure as the load increases is observed, however, the value is lower than the hardness, as often reported. The contact area is found to be a simple truncation of the sphere by a hard flat.
Issue Section:
Research Papers
1.
Greenwood
, J. A.
, and Williamson
, J. B. P.
, 1966, “Contact of Nominally Flat Surfaces
,” Proc. R. Soc. London, Ser. A
1364-5021, 295
, pp. 300
–319
.2.
Abbott
, E. J.
, and Firestone
, F. A.
, 1933, “Specifying Surface Quality—A Method Based on Accurate Measurement and Comparison
,” Mech. Eng. (Am. Soc. Mech. Eng.)
0025-6501, 55
, p. 569
.3.
Chang
, W. R.
, Etsion
, I.
, and Bogy
, D. B.
, 1987, “An Elastic-Plastic Model for the Contact of Rough Surfaces
,” ASME J. Tribol.
0742-4787, 109
, pp. 257
–263
.4.
Horng
, J. H.
, 1998, “An Elliptic Elastic-Plastic Asperity Microcontact Model for Rough Surface
,” ASME J. Tribol.
0742-4787, 120
, pp. 82
–88
.5.
Zhao
, Y.
, Maietta
, D. M.
, and Chang
, L.
, 2000, “An Asperity Microcontact Model Incorporating the Transition from Elastic Deformation to Fully Plastic Flow
,” ASME J. Tribol.
0742-4787, 122
, pp. 86
–93
.6.
Jeng
, Y. R.
, and Wang
, P. Y.
, 2003, “An Elliptical Microcontact Model Considering Elastic, Elastoplastic, and Plastic Deformation
,” ASME J. Tribol.
0742-4787, 125
, pp. 232
–240
.7.
Vu-Quoc
, L.
, and Zhang
, X.
, 1999, “An Elastoplastic contact Force-Displacement Model in the Normal Direction: Displacement-Driven Version
,” Proc. R. Soc. London, Ser. A
1364-5021, 455
, pp. 4013
–4044
.8.
Vu-Quoc
, L.
, Zhang
, X.
, and Lesburg
, L.
, 2000, “A Normal Force-Displacement Model for Contacting Spheres Accounting for Plastic Deformation: Force-Driven Formulation
,” ASME J. Appl. Mech.
0021-8936, 67
, pp. 363
–371
.9.
Mesarovic
, S. D.
, and Fleck
, N. A.
, 1999, “Spherical Indentation of Elastic-Plastic Solids
,” Proc. R. Soc. London, Ser. A
1364-5021, 455
, pp. 2707
–2728
.10.
Mesarovic
, S. D.
, and Fleck
, N. A.
, 2000, “Frictionless Indentation of Dissimilar Elastic-Plastic Spheres
,” Int. J. Solids Struct.
0020-7683, 37
, pp. 7071
–7091
.11.
Li
, L.-Y.
, Wu
, C.-Y.
, and Thornton
, C.
, 2002, “A Theoretical Model for the Contact of Elastoplastic Bodies
,” Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci.
0954-4062, 216
, pp. 421
–431
.12.
Kogut
, L.
, and Etsion
, I.
, 2002, “Elastic-Plastic Contact Analysis of a Sphere and a Rigid Flat
,” ASME J. Appl. Mech.
0021-8936, 69
, pp. 657
–662
.13.
Jackson
, R. L.
, and Green
, I.
, 2003, “A Finite Element Study of Elasto-plastic Hemispherical Contact
,” Proceeding of 2003 STLE/ASME Joint Tribology Conference
, 2003TRIB-268.14.
Jackson
, R. L.
, and Green
, I.
, 2005, “A Finite Element Study of Elasto-Plastic Hemispherical Contact Against a Rigid Flat
,” ASME J. Tribol.
0742-4787, 127
, pp. 343
–354
.15.
Sloetjes
, J. W.
, Schipper
, D. J.
, Lugt
, P. M.
, and Tripp
, J. H.
, 2000, “The Determination of Changes in Surface Topography Using Image Processing Techniques
,” in Proceedings of the International Tribology Conference
, Nagasaki
.16.
Sloetjes
, J. W.
, Tasan
, Y. C.
, De Rooij
, M. B.
, and Schipper
, D. J.
, 2002, “Algorithm for Determining Changes in Micro-Geometry Using Image Processing Techniques
,” in Proceedings of the 2nd Asia International Conference on Tribology
, Asiatrib ’02, Cheju Island
, Korea.17.
Johnson
, K. L.
, 1968, “An Experimental Determination of the Contact Stresses Between Plastically Deformed Cylinders and Spheres
,” Engineering Plasticity
, Cambridge University Press
, Cambridge
, pp. 341
–361
.18.
Chaudhri
, M. M.
, 1987, “The Plastic Deformation of Single Asperities by Hard Flats
,” Proc. Inst. Mech. Eng.
0020-3483, 158
, pp. 1003
–1012
.19.
Tabor
, D.
, 1951, The Hardness of Metals
, Clarendon Press
, Oxford, UK
.20.
Chaudhri
, M. M.
, Hutchings
, I. M.
, and Makin
, P. L.
, 1984, “Plastic Compression of Spheres
,” Philos. Mag. A
0141-8610, 49
, pp. 493
–503
.Copyright © 2006
by American Society of Mechanical Engineers
You do not currently have access to this content.