The present work is a parametric study of the pressure pattern in a two-dimensional recess of a hybrid journal bearing (HJB). It is known that theoretical models of HJB are largely dependent on the recess pressure pattern especially for severe working conditions (high rotation speeds, shallow pockets, etc.). The difficulty is that the recess flow is dominated by the interaction of viscous and inertia forces and cannot be analyzed using a thin film model. The present analysis is based on the numerical resolution of the two-dimensional Navier-Stokes equations where only one recess is modeled (with the film lands and the supply region), the fluid being regarded as incompressible and isothermal. Both the laminar and the turbulent flow regimes are considered. The study is governed by two parameters, one related to the HJB operating conditions and the other related to the recess geometric characteristics. The first parameter is the ratio of the runner versus the supply Reynolds number, Rer/Res{0,1/4,1/2,1,4,8}. The supply Reynolds number is fixed at 100 for the laminar regime and at 5000 for the turbulent one. The second parameter is the ratio of the recess depth versus the film thickness. Six values of this ratio are considered, ranging from 4 (shallow recess) to 152 (deep recess). Detailed pressure patterns on the runner wall are presented in a systematic manner giving a clear insight of the flow effects intervening in the recess and of their mutual interaction. Some effects are explained by analyzing the recirculation zones inside the recess. It is also shown that for certain parameters turbulent flows have qualitatively similar effects as laminar ones but they can also have specific trends. In order to sustain this remark, the pressure variation at the recess downstream end is analyzed in the paper. Finally, the present results and specially the turbulent ones are intended to contribute to the understanding of viscous and inertia effects interactions in a recess flow and to represent a database in view of HJB theoretical modeling.

1.
Pan
,
C. H. T.
,
1974
, “
Calculation of Pressure, Shear and Flow in Lubrication Films for High Speed Bearings
,”
ASME J. Lubr. Technol.
,
98
, pp.
167
174
.
2.
Constantinescu
,
V. N.
, and
Galetuse
,
S.
,
1976
, “
Pressure Drop Due to Inertia Forces in Step Bearings
,”
ASME J. Lubr. Technol.
,
98
, pp.
167
174
.
3.
Tipei
,
N.
,
1982
, “
Flow and Pressure Head at the Inlet of Narrow Passages Without Upstream Free Surface
,”
ASME J. Lubr. Technol.
,
104
, pp.
196
202
.
4.
Tuck
,
E. O.
, and
Bentwich
,
M.
,
1983
, “
Sliding Sheets: Lubrication with Comparable Viscous and Inertia Forces
,”
J. Fluid Mech.
,
135
, pp.
51
69
.
5.
Tichy
,
J. A.
, and
Bourgin
,
P.
,
1985
, “
The Effect of Inertia in Lubrication Flow Including Entrance and Initial Conditions
,”
ASME J. Appl. Mech.
,
52
, pp.
759
765
.
6.
Buckholz
,
R. H.
,
1987
, “
The Effect of Lubricant Inertia Near the Leading Edge of a Plane Slide Bearing
,”
ASME J. Tribol.
,
109
, pp.
60
64
.
7.
Mori
,
A.
,
Makino
,
T.
, and
Mori
,
H.
,
1992
, “
Entry Flow and Pressure Jump in Submerged Multi-Pad Bearings and Grooved Bearings
,”
ASME J. Tribol.
,
114
, pp.
370
378
.
8.
Chaomleffel, J. P., 1983, “Influence of Inertial Forces on Hybrid Lubrication,” (in French) Ph.D. thesis, INSA Lyon, France.
9.
Constantinescu, V. N., 1987, “On Conditions at the Inlet Edge of a Lubricated Film Operating at Large Reynolds Numbers,” (in Romanian) The 5-th Conference on Friction, Lubrication and Wear, Bucharest, Sept. 1987.
10.
Arghir, M., Attar, S. E., and Nicolas, D., 1996, “Pressure Drop In A Hydrostatic Pocket. Experimental and Theorical Results,” Proceedings of the Leeds-Lyon Symposium, Elsevier Science B.V., pp. 423–432.
11.
Ho
,
Y. S.
, and
Chen
,
N. N.
,
1984
, “
Pressure Distribution in a Six Pocket Hydrostatic Journal Bearing
,”
Wear
,
98
, pp.
89
100
.
12.
Chaomleffel
,
J. P.
, and
Nicolas
,
D.
,
1985
, “
Experimental Investigations of Hybrid Journal Bearings
,”
Tribol. Trans.
,
19
, pp.
253
259
.
13.
San Andre´s, L., and Velthuis, J., 1991, “Laminar Flow in a Recess of a Hydrostatic Bearing,” STLE Paper No. 91TC3B3, STLE/ASME Tribology Conference, October 1316, St. Louis, Missouri.
14.
Braun, M. J., Dzodzo, and M., Lattime, S., 1996, “Some Qualitative and Quantitative Aspects of Flow in a Hydrostatic Journal Bearing Pocket,” FED-Vol. 239, Fluid Engineering Division Conference, 4, ASME 1996 pp. 109–114.
15.
Braun, M. J., and Dzodzo, M., 1996, “A Three Dimensional Model for a Hydrostatic Bearing,” 32nd AIAA/ASME/SAE/ASEE Joint Propulsion Conference July 1–3, 1996/Lake Buena Vista, FL.
16.
Braun
,
M. J.
, and
Dzodzo
,
M.
,
1996
, “
Three Dimentional Flow and Pressure Patterns in a Hydrostatic Journal Bearing Pocket
,”
ASME J. Tribol.
,
119
, pp.
711
719
.
17.
Braun
,
M. J.
,
Choy
,
F. K.
, and
Zhu
,
M.
,
1993
, “
The Effects of a Hydrostatic Pocket Aspect Ratio, and Its Supply Orifice Position and Attack Angle on Steady-State Flow Pattern, Pressure and Shear Characteristics
,”
ASME J. Tribol.
,
115
(
4
), pp.
678
886
.
18.
Braun
,
M. J.
,
Choy
,
F. K.
, and
Zhu
,
N.
,
1995
, “
Flow Pattern and Dynamic Characteristics of a Lightly Loaded Hydrostatic Pocket of variable Aspect Ratio and Supply Jet Strength
,”
STLE Trans.
,
38
(
1
), pp.
128
136
.
19.
Braun
,
M. J.
, and
Dzodzo
,
M.
,
1995
, “
Effects of Hydrostatic Pocket Shape on the Flow Patterns and Pressure Distribution
,”
Int. J. Rotating Mach.
,
1
(
3-4
), pp.
225
235
.
20.
Braun
,
M. J.
, and
Dzodzo
,
M.
,
1995
, “
Effects of the Feedline and Hydrostatic Pocket Depth on the Flow Patterns and Pressure Distribution
,”
ASME J. Tribol.
,
117
(
2
), pp.
224
233
.
21.
Hendricks
,
R. C.
,
Steinetz
,
B. M.
,
Athavale
,
M. M.
,
Przekwas
,
A. J.
,
Braun
,
M. J.
,
Choy
,
F. K.
,
Dzodzo
,
M.
,
Kudriavstev
,
V. V.
,
Mullen
,
R. L.
, and
von Pragenau
,
G. L.
,
1995
, “
Interactive Development of Seals, Bearings, and Secondary Flow Systems with the Power Stream
,”
Int. J. Rotating Mach.
,
1
(
3-4
), pp.
153
185
.
22.
Dzodzo
,
M.
, and
Braun
,
M. J.
,
1996
, “
Pressure and Flow Characteristics in a Shallow Hydrostatic Pocket with Rounded Pocket/Land Joints
,”
Tribol. Int.
, Austrib Special Issue,
29
(
1
) pp.
69
76
.
23.
Patankar, S. V., 1980, Numerical Heat Transfer and Fluid Flow, Hemisphere, Washington, D.C.
24.
Ferziger, J. L., and Peric, M., 1996, Computational Methods for Fluid Dynamics, Springer Verlag, Heidelberg.
25.
Launder
,
B. E.
, and
Spalding
,
D. B.
,
1974
, “
The Numerical Computation of Turbulent Flows
,”
Comput. Methods Appl. Mech. Eng.
,
3
, pp.
269
289
.
26.
Roache
,
P. J.
,
1994
, “
Perspective: A Method for Uniform Reporting of Grid Refinement Studies
,”
ASME J. Fluids Eng.
,
116
, pp.
405
413
.
You do not currently have access to this content.