Single crystal nickel base superalloy turbine blades are being utilized in rocket engine turbopumps and turbine engines because of their superior creep, stress rupture, melt resistance, and thermomechanical fatigue capabilities over polycrystalline alloys. High cycle fatigue induced failures in aircraft gas turbine and rocket engine turbopump blades is a pervasive problem. Blade attachment regions are prone to fretting fatigue failures. Single crystal nickel base superalloy turbine blades are especially prone to fretting damage because the subsurface shear stresses induced by fretting action at the attachment regions can result in crystallographic initiation and crack growth along octahedral planes. This paper presents contact stress evaluation in the attachment region for single crystal turbine blades used in the NASA alternate advanced high pressure fuel turbo pump for the space shuttle main engine. Single crystal materials have highly anisotropic properties making the position of the crystal lattice relative to the part geometry a significant factor in the overall analysis. Blades and the attachment region are modeled using a large-scale three-dimensional finite element model capable of accounting for contact friction, material anisotropy, and variation in primary and secondary crystal orientation. Contact stress analysis in the blade attachment regions is presented as a function of coefficient of friction and primary and secondary crystal orientation. Fretting stresses at the attachment region are seen to vary significantly as a function of crystal orientation. The stress variation as a function of crystal orientation is a direct consequence of the elastic anisotropy of the material. Fatigue life calculations and fatigue failures are discussed for the airfoil and the blade attachment regions.

Issue Section:
Technical Papers
Keywords:
gas turbines, nickel alloys, mechanical contact, wear testing, rough surfaces, tribology, lubrication, sliding friction, crystallography, interface phenomena, Fretting, Fatigue, High Cycle Fatigue (HCF), Single Crystal, Crystal Orientation, Nickel-Base Superalloy, Face Centered Cubic (FCC), Turbine Blade, Blade Attachment
Topics:
Blades, Crystal structure, Crystals, Fracture (Materials), Stress, Superalloys, Turbine blades, Nickel, Fatigue life
1.
Hills, D. A., and Nowell, D., 1994, Mechanics of Fretting Fatigue, Kluwer, Deventer.
2.
Cowles, B. A., 1996, “High Cycle Fatigue in Aircraft Gas Turbines—An Industry Perspective,” Int. J. Fract., pp. 1–16.
3.
Dombromirski, J., 1990, “Variables of Fretting Process: Are There 50 of Them?” Standardization of Fretting Fatigue Test Methods and Equipment, ASTM, Metals Park, OH, pp. 60–68.
4.
Deluca, D., and Annis. C, 1995, “Fatigue in Single Crystal Nickel Superalloys,” Tech. Report No. FR23800, Office of Naval Research, Department of the Navy, Washington, DC.
5.
Sims, C. T., 1987, Superalloys: Genesis and Character, Superalloys-II, C. T. Sims, N. S. Stoloff, and W. C. Hagel, eds., Wiley, New York, p. 1.
6.
VerSnyder
,
F. L.
, and
Guard
,
R. W.
,
1960
, “
Directional Grain Structure for High Temperature Strength
,”
Trans. ASM
,
52
, pp.
485
–
492
.
7.
Gell, M., and Duhl, D. L., 1986, “The Development of Single Crystal Superalloy Turbine Blades,” Processing and Properties of Advanced High-Temperature Materials, S. M. Allen, R. M. Pelloux, and R. Widmer, eds., ASM, Metals Park, OH, p. 41.
8.
Moroso, J., 1999, “Effect of Secondary Orientation on Fatigue Crack Growth in Single Crystal Turbine Blades,” M. S. thesis, Mechanical Engineering Department, University of Florida, Gainesville, FL.
9.
Arakere, N. K., and Swanson, G., 2000, “Effect of Crystal Orientation on Fatigue Failure of Single Crystal Nickel Base Turbine Blade Superalloys,” Proc. ASME IGTI Conference, Munich, Germany.
10.
Arakere, N. K., and Swanson, G., 2000, “Effect of Crystal Orientation on Analysis of Single Crystal, Nickel Base Turbine Blade Superalloys,” NASA Report No. NASA/TP-210074, Washington, DC.
11.
Giannokopoulos
,
A. E.
,
Lindley
,
T. C.
, and
Suresh
,
S.
,
1998
, “
Aspects of Equivalence Between Contact Mechanics and Fracture Mechanics: Theoretical Connections and a Life Prediction Methodology for Fretting Fatigue
,”
Acta Mater.
,
46
, pp.
2955
–
2968
.
12.
Szolwinski
,
M. P.
, and
Farris
,
T. N.
,
1996
, “
Mechanics of Fretting Fatigue Crack Formation
,”
Wear
,
198
, pp.
93
–
107
.
13.
Attia, M. H., and Waterhouse, R. B., 1992, Standardization of Fretting Fatigue Test Methods and Equipment, ASTM Publication No. 04-011590-30, STP 1159.
14.
Hoeppner, D. W., 1990, “Mechanisms of Fretting Fatigue and their Impact on Test Methods Development,” Standardization of Fretting Fatigue Test Methods and Equipment, ASTM, Metals Park, OH, pp. 23–32.
15.
Vingsbo
,
O.
, and
Soderberg
,
D.
,
1988
, “
On Fretting Maps
,”
Wear
,
126
, pp.
131
–
147
.
16.
Ruiz
,
C.
,
Boddington
,
P. H. B.
, and
Chen
,
K. C.
,
1984
, “
An Investigation of Fatigue and Fretting in a Dovetail Joint
,”
Exp. Mech.
,
24
, pp.
208
–
217
.
17.
Stouffer, D. C., and Dame, L. T., 1996, Inelastic Deformation of Metals, Wiley, New York.
18.
DeLuca, D. P., Pratt & Whitney, Government Engines and Space Propulsion, Mechanics of Materials, West Palm Beach, FL (personal communication).
19.
Telesman
,
J.
, and
Ghosn
,
L.
,
1989
, “
The Unusual Near Threshold FCG Behavior of a Single Crystal Superalloy and the Resolved Shear Stress as the Crack Driving Force
,”
Eng. Fract. Mech.
,
34
, pp.
1183
–
1196
.
20.
Deluca, D. P., and Cowles, B. A., 1989, “Fatigue and Fracture of Single Crystal Nickel in High Pressure Hydrogen,” Hydrogen Effects on Material Behavior, N. R. Moody and A. W. Thomson, eds., TMS, Warrendale, PA.
21.
John, R., DeLuca, D. P., Nicholas, T., and Porter, J., 1998, “Near-Threshold Crack Growth Behavior of a Single Crystal Ni-Base Superalloy Subjected to Mixed Mode Loading,” Mixed-Mode Crack Behavior, K. J. Miller and D. L. McDowell, eds., ASTM, Metals Park, OH.
22.
Pratt and Whitney, 1996, “SSME Alternate Turbopump Development Program HPFTP Critical Design Review,” Technical Report No. P&W FR24581-1.
23.
Sayyah, T., 1999, “Alternate Turbopump Development Single Crystal Failure Criterion for High Pressure Fuel Turbopump First Stage Blades,” Technical Report No.: 621-025-99-001, NASA Contract NAS 8-40836, NASA, Washington, DC.
24.
Lekhnitskii, S. G., 1963, Theory Of Elasticity of an Anisotropic Elastic Body, Holden-Day Inc.
25.
Kandil, F. A., Brown, M. W., and Miller, K. J., 1982, Biaxial Low Cycle Fatigue of 316 Stainless Steel at Elevated Temperatures, Metals Society, London, pp. 203–210.
26.
Socie, D. F., Kurath, P., and Koch, J., 1985, “A Multiaxial Fatigue Damage Parameter,” presented at the Second International Symposium on Multiaxial Fatigue, Sheffield, U.K.
27.
Fatemi
,
A.
, and
Socie
,
D.
,
1988
, “
A Critical Plane Approach to Multiaxial Fatigue Damage Including Out-of-Phase Loading
,”
Fatigue Fract. Eng. Mater. Struct.
,
11
, pp.
149
–
165
.
28.
Smith
,
K. N.
,
Watson
,
P.
, and
Topper
,
T. M.
,
1970
, “
A Stress-Strain Function for the Fatigue of Metals
,”
J. Mater.
,
5
, pp.
767
–
778
.
29.
Banantine, J. A., and Socie, D. F., 1985, “Observations of Cracking Behavior in Tension and Torsion Low Cycle Fatigue,” presented at ASTM Symposium on Low Cycle Fatigue-Directions for the Future, Philadelphia, ASTM, Metals Park, OH.
Copyright © 2001
 by ASME
You do not currently have access to this content.