In this article, an experimental study on boiling heat transfer and fluid flow in microtubes at high mass fluxes is presented. De-ionized water flow was investigated over a broad range of mass flux (1000 kg/m2s–7500 kg/m2s) in microtubes with inner diameters of ∼ 250 μm and ∼685 μm. The reason for using two different capillary diameters was to investigate the size effect on flow boiling. De-ionized water was used as working fluid, and the test section was heated by Joule heating. Heat transfer coefficients and qualities were deduced from local temperature measurements. It was found that high heat removal rates could be achieved at high flow rates under subcooled boiling conditions. It was also observed that heat transfer coefficients increased with mass flux, whereas they decreased with local quality and heat flux. Moreover, experimental heat flux data were compared with partial boiling correlations and fully developed boiling correlations. It was observed that at low wall superheat values, there was only a small inconsistency between the experimental data and the conventional partial boiling prediction method of Bergles, while the subcooled and low quality fully developed boiling heat transfer correlation of Kandlikar could fairly predict experimental results at high wall superheat values.
Skip Nav Destination
e-mail: kosara@sabanciuniv.edu
Article navigation
December 2011
Research Papers
Low Mass Quality Flow Boiling in Microtubes at High Mass Fluxes
Mehmed Rafet Özdemir,
Mehmed Rafet Özdemir
Mechatronics Engineering Program,
Sabancı University
, Tuzla, Istanbul 34956, Turkey
Search for other works by this author on:
Alihan Kaya,
Alihan Kaya
Mechatronics Engineering Program,
Sabancı University
, Tuzla, Istanbul 34956, Turkey
Search for other works by this author on:
Ali Koşar
Ali Koşar
Mechatronics Engineering Program,
e-mail: kosara@sabanciuniv.edu
Sabancı University
, Tuzla, Istanbul 34956, Turkey
Search for other works by this author on:
Mehmed Rafet Özdemir
Mechatronics Engineering Program,
Sabancı University
, Tuzla, Istanbul 34956, Turkey
Alihan Kaya
Mechatronics Engineering Program,
Sabancı University
, Tuzla, Istanbul 34956, Turkey
Ali Koşar
Mechatronics Engineering Program,
Sabancı University
, Tuzla, Istanbul 34956, Turkey
e-mail: kosara@sabanciuniv.edu
J. Thermal Sci. Eng. Appl. Dec 2011, 3(4): 041001 (9 pages)
Published Online: October 13, 2011
Article history
Received:
January 28, 2011
Revised:
August 12, 2011
Online:
October 13, 2011
Published:
October 13, 2011
Citation
Rafet Özdemir, M., Kaya, A., and Koşar, A. (October 13, 2011). "Low Mass Quality Flow Boiling in Microtubes at High Mass Fluxes." ASME. J. Thermal Sci. Eng. Appl. December 2011; 3(4): 041001. https://doi.org/10.1115/1.4005053
Download citation file:
Get Email Alerts
Cited By
Research on thermal comfort of human body under localized automotive air conditioning
J. Thermal Sci. Eng. Appl
Temperature Analysis of Waveform Water Channel for High-Power Permanent Magnet Synchronous Motor
J. Thermal Sci. Eng. Appl
Related Articles
Subcooled Boiling Heat Transfer for Turbulent Flow of Water in a Short Vertical Tube
J. Heat Transfer (January,2010)
Variations of Buoyancy-Induced Mass Flux From Single-Phase to Two-Phase Flow in a Vertical Porous Tube With Constant Heat Flux
J. Heat Transfer (August,1999)
Jet Impingement Boiling From a Circular Free-Surface Jet During Quenching: Part 1—Single-Phase Jet
J. Heat Transfer (October,2001)
Enhanced Subcooled Flow Boiling Heat Transfer in Microchannel With Piranha Pin Fin
J. Heat Transfer (November,2017)
Related Proceedings Papers
Related Chapters
Liquid Cooled Systems
Thermal Management of Telecommunication Equipment, Second Edition
Thermal Design Guide of Liquid Cooled Systems
Thermal Design of Liquid Cooled Microelectronic Equipment
Liquid Cooled Systems
Thermal Management of Telecommunications Equipment