Abstract

Waste heat recovery usually involves indirect heat transfer, between two fluids, across a diathermic wall; and finned-type recuperative heat exchangers are preferred for the stipulated task. Strategic integration of vortex generators in aforesaid systems produces such flow structures which greatly improve the effectiveness of the heat exchanger. Often heat exchanger designers place generators at under-performing locations, despite knowing the best ones, due to manufacturing restrictions. Since the generators' geometry too affects the thermal augmentation, positional compromise can be duly compensated. This study uses a computational analysis to investigate the effect of varying the geometric aspect ratio of the generators. For a conclusive assessment of the geometric designs, the attack angles espoused for integrating the generators cater to the entire effective range. In order to understand the changes in flow characteristics, velocity fields are examined which suggests that reducing the generators' aspect ratio aids in diverting the oncoming flow, and so limits the tube wake zones. Additionally, the swirling flow generated by the vortex generators facilitates bulk mixing across a large fin surface. Both flow modifications together give a substantial boost to the thermal performance, thereby downsizing the system.

References

1.
Arora
,
A.
, and
Subbarao
,
P. M. V.
,
2023
, “
Augmented Performance and Wake Management in Finned Tube Arrays Through Hierarchical Deployment of Toe-Out Winglets
,”
ASME J. Heat Transfer-Trans. ASME
,
145
(
12
), p.
121002
.
2.
Jacobi
,
A. M.
, and
Shah
,
R. K.
,
1995
, “
Heat Transfer Surface Enhancement Through the Use of Longitudinal Vortices: A Review of Recent Progress
,”
Exp. Therm. Fluid. Sci.
,
11
(
3
), pp.
295
309
.
3.
Deshmukh
,
P. W.
,
Kasar
,
S. V.
, and
Prabhu
,
S. V.
, “
A Comprehensive Compendium on Passive Augmentation Techniques for Enhancement of Single-Phase Heat Transfer Coefficients in Heat Exchanger Tubes Under Laminar and Turbulent Flow Conditions
,”
Heat Transfer Eng.
,
44
(
6
), pp.
530
579
.
4.
Chu
,
P.
,
He
,
Y. L.
,
Lei
,
Y. G.
,
Tian
,
L. T.
, and
Li
,
R.
,
2009
, “
Three-Dimensional Numerical Study on Fin-and-Oval-Tube Heat Exchanger With Longitudinal Vortex Generators
,”
Appl. Therm. Eng.
,
29
(
5–6
), pp.
859
876
.
5.
Arora
,
A.
, and
Subbarao
,
P. M. V.
,
2024
, “
Integration of Winglet Type Vortex Generators in Finned-Tube Heat Exchangers for a Sizeable Capacity Augmentation
,”
Proc. Inst. Mech. Eng. Part C: J. Mech. Eng. Sci.
,
238
(
7
), pp.
3067
3083
.
6.
Khan
,
T. A.
, and
Li
,
W.
,
2018
, “
Optimal Configuration of Vortex Generator for Heat Transfer Enhancement in a Plate-Fin Channel
,”
ASME J. Therm. Sci. Eng. Appl.
,
10
(
2
), p.
021013
.
7.
Popov
,
I. A.
,
Zhukova
,
Y. V.
,
Baranova
,
T. A.
,
Kаdyrov
,
P. T.
,
Mironov
,
A. A.
,
Marshalova
,
G. S.
,
Skrypnik
,
A. N.
,
Danilchik
,
E. S.
, and
Chorny
,
A. D.
,
2022
, “
Thermal-Hydraulic Performance of a Single Round Tube With Surface Vortex Generators
,”
Heat Transfer Res.
,
53
, pp.
29
(
9
)–
41
.
8.
Akcayoglu
,
A.
, and
Nazli
,
C.
,
2016
, “
Thermal Enhancement of Triangular Fins Based on Spanwise Distance of Vortex Generators
,”
Proc. Inst. Mech. Eng. Part C: J. Mech. Eng. Sci.
,
231
(
13
), pp.
2554
2566
.
9.
Arora
,
A.
, and
Subbarao
,
P. M. V.
,
2023
, “
Investigation of Performance Augmentation Due to Geometric Modification of Vortex Generators Placed in Fin-and-Tube Heat Exchangers
,”
ASME J. Therm. Sci. Eng. Appl.
,
15
(
5
), p.
050906
.
10.
Wu
,
J. M.
, and
Tao
,
W. Q.
,
2008
, “
Numerical Study on Laminar Convection Heat Transfer in a Channel With Longitudinal Vortex Generator. Part B: Parametric Study of Major Influence Factors
,”
Int. J. Heat Mass Transfer
,
51
(
13–14
), pp.
3683
3692
.
11.
Wu
,
J. M.
, and
Tao
,
W. Q.
,
2008
, “
Numerical Study on Laminar Convection Heat Transfer in a Rectangular Channel With Longitudinal Vortex Generator. Part A: Verification of Field Synergy Principle
,”
Int. J. Heat Mass Transfer
,
51
(
5–6
), pp.
1179
1191
.
12.
Zhang
,
Y.-H.
,
Wu
,
X.
,
Wang
,
L.-B.
,
Song
,
K.-W.
,
Dong
,
Y.-X.
, and
Liu
,
S.
,
2008
, “
Comparison of Heat Transfer Performance of Tube Bank Fin With Mounted Vortex Generators to Tube Bank Fin With Punched Vortex Generators
,”
Exp. Therm. Fluid. Sci.
,
33
(
1
), pp.
58
66
.
13.
Arora
,
A.
, and
Subbarao
,
P. M. V.
,
2025
, “
Hierarchical Deployment of Vortex Generators for Wake Management in Finned-Tube Heat Exchanger
,”
Heat Transfer Eng.
,
46
(
1
), pp.
16
35
.
14.
Wu
,
J.
,
Liu
,
P.
,
Yu
,
M.
,
Liu
,
Z.
, and
Liu
,
W.
,
2022
, “
Thermo-Hydraulic Performance and Exergy Analysis of a Fin-and-Tube Heat Exchanger With Sinusoidal Wavy Winglet Type Vortex Generators
,”
Int. J. Therm. Sci.
,
172
(
Part A
), p.
107274
.
You do not currently have access to this content.