Abstract

Special test equipment is required in order to determine the superplastic flow characteristics of advanced aluminum alloys such as the low-density aluminum-lithium alloys and the high-temperature intermetallics (processed by rapid solidification, mechanically alloying, powder metallurgy techniques). The superplastic flow characteristics under optimum conditions of strain race and temperature are necessary as input data to the computer process model weed to predict optimum pressure-time cycles for the SPF process. Most published tensile flow stress data for superplastic deformation was developed under constant crosshead speeds and at atmospheric pressure. In order to establish accurate flow characteristics, testing must be conducted: (1) at a closely controlled temperature, (2) at a controlled constant true strain rate, and (3) under hydrostatic pressure (to prevent cavitation). This paper discusses the design and development of a test system with these capabilities and also highlights typical results for three aluminum-lithium alloys.

Issue Section:
Research Papers
Keywords:
superplastic deformation, aluminum-lithium, strain rate sensitivity, tensile instability

References

1.
Pilling
,
J.
 and
Ridley
,
R.
,
Superplasticity in Crystalline Solids
,
Camelot Press
,
Southampton
,
The Institute of Metals
,
1989
, pp.
6
-
88
.
2.
Chandra
,
N.
 and
Goforth
,
R.
, “
An Analytical Model for Axisymmetric Superplastic Metal Forming Processes
,”
TMS Technical Paper
No. A87-11,
1987
.
3.
Goforth
,
R. E.
,
Chandra
,
N.
, and
George
,
D.
, “
Analysis of the Cone Test to Evaluate Superplastic Forming Characteristics of Sheet Metal
,”
Superplasticity in Aerospace
,
Heikkenen
 
H. C.
 and
McNelly
 
T. R.
, Eds.,
The Metallurgical Society
,
Warrendale, PA
,
1988
, pp.
149
-
166
.
4.
Chandra
,
N.
,
Goforth
,
R. E.
, and
Phillips
,
L.
, “
Mechanical Characterization of Superplastic Materials Using Modified Cone Test
,”
Superplasticity in Aerospace II
,
McNelley
 
T. R.
 and
Heikkenea
 
H. C.
, Eds.,
The Minerals, Metals, and Materials Society
,
Warrendale, PA
,
1990
, pp.
67
-
85
.
5.
Ghosh
, ,
A. K.
 Dr.,
Rockwell International Science Center
,
Thousand Oaks, CA
, (currently at the
University of Michigan
,
Ann Arbor, MI
). Private conversation with author,
1988
.
6.
Mukherjee
, ,
A. K.
 Dr.,
Div. of Materials Science and Engineering, Dept. of Mechanical Engineering, University of California
, Davis, CA, Private conversation with author,
1988
.
7.
Pilling
, ,
John
 Dr..
Dept. of Metallurgical Engineering, Michigan Technological University (formerly at the University of Manchester)
, Houghton, MI, Private conversation with author,
1988
.
8.
Kopp
,
C. K.
, “
Experimental Superplastic Characterization of Advanced Aluminum Alloys
,” M.S. thesis,
Dept. of Mechanical Engineering, Texas A&M University
, College Station, TX,
1991
.
9.
Hedworth
,
J.
 and
Stowell
,
M. J.
, “
The Measurement of Strain-Rate Sensitivity in Superplastic Alloys
,”
Journal of Materials Science
 0022-2461, Vol.
6
,
1971
, pp.
1061
-
1069
.
Google Scholar
Crossref
Search ADS
 
10.
Goforth
,
R. E.
,
Srinivasan
,
M.
, and
Chandra
,
N.
, “
Superplastic Flow Characteristics and Microstructural Analysis of Aluminum-Lithium Alloy 2090-OE16
,”
Superplasticity in Aerospace II
,
McNelley
 
T. R.
 and
Heikkenen
 
H. C.
, Eds.,
The Minerals, Metals, and Materials Society
,
Warrendale, PA
,
1990
, pp.
285
-
302
.
11.
Goforth
,
R. E.
,
Srinivasan
,
M.
, and
Chandra
,
N.
, “
A Comparative Study of the Superplastic Behavior of Two Dynamically Recrystallizing Aluminum-Lithium Alloys
,”
International Conference on Superplasticity in Advanced Materials
,
Osaka. Japan
. June 3–6, 1991. (conference Proceedings to be published).
12.
Adabbo
,
H. E.
,
Gonzales-Doncel
,
G.
,
Ruano
,
O. A.
,
Belzunce
,
J. M.
, and
Sherby
,
O. D.
, “
Strain Hardening During Superplastic Deformation of Al-7475 Alloy
,”
Journal of Materials Resources
, Vol.
4
,
1989
, p. 587.
13.
Goforth
,
R. E.
 and
Srinivasan
,
M.
, “
Superplastic Forming Characteristics of 2090 and 8090 Al-Li Alloys
,”
Final Report
,
Lockheed Aeronautical Systems Co
. Burbank, CA, Project 27390 ME,
02
07
1990
.
14.
Hart
,
E. W.
, “
Theory of the Tensile Test
,”
Acta Metallurgica
 0001-6160 https://doi.org/10.1016/0001-6160(67)90211-8, Vol.
15
,
1967
, pp.
351
-
355
.
Google Scholar
Crossref
Search ADS
 
15.
Goforth
,
R. E.
 and
Srinivasan
,
M.
, “
Uniaxial Tensile Testing of Weldalite 049 Under Constant Pure Strain Rates and Dual Strain Rates
,”
Final Report
,
Martin-Marietta Corp.
, New Orleans, LA, Project 28390 ME,
03
01
1991
.
16.
Belasubramanian
,
R.
, “
Microstructural Characterization of Superplastic Aluminum-Lithium Alloys
,” M.S. thesis,
Dept. of Mechanical Engineering, Texas A&M University
, College Station, TX,
1991
.
17.
Nix
,
W. E.
, “
On Some Fundamental Aspects of Superplastic Flow
,”
Superplastic Forming Symposium (ASM)
,
WESTEC
,
Los Angeles
,
22
03
1984
.
This content is only available via PDF.
All rights reserved. This material may not be reproduced or copied, in whole or in part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of ASTM International.
You do not currently have access to this content.