To make a better thermal storage system that uses air as the heat transfer fluid flowing through a packed-bed of ceramic spheres (Al 2 O 3 ) as thermal storage materials, the present work studied cases using multiple small-diameter thin tanks to replace a large-diameter big tank while keeping the same total volume and the same air flow rate. Performance analysis of thermal storage has been conducted for comparison and optimization. The long flow passage and faster flow velocity of air in the small-diameter tanks was found to significantly benefit thermal storage performance compared to that of a short big tank. It resulted in a longer duration of discharge of high temperature airflow, if the same operation time is applied to the two situations. The faster airflow enhances the heat transfer between air and thermal storage material, although it incurs larger pressure loss. Overall, the energy storage efficiency of using several thin tanks can be significantly better than that of using a big short tank if the height-diameter ratio in the multiple thin tanks is properly optimized. The optimization methodology and results are of great significance to the development of thermal storage systems that use air as heat transfer fluid and rocks or ceramic spheres as the packed-bed material for thermal storage.

Due to their thermal storage capability, concentrated solar power (CSP) plants have flexibility on electricity dispatch, being able to participate in balancing power markets. The development of an optimum electricity delivery schedule should be fast to react to updated forecast and the dynamic electricity markets, apart from considering best operational practices, as it brings significant cost reductions and improvement in plant performance. Therefore, dispatch optimization tools should combine financial and operational optimization with acceptable computational time. In this context, an innovative dispatch optimization algorithm used to derive a CSP plant operation schedule is presented. FRED is a heuristic rule-based algorithm used to optimize financial income while considering plant best operational practices. Simulations performed with a CSP plant tower model following FRED optimization strategy show the possibility of improved financial results with fast dispatch planning, ensuring the importance of this technology in the pathway to a highly renewable energy mix.

Energy storage helps in waste management, environmental protection, saving of fossil fuels, cost effectiveness, and sustainable growth. Phase change material (PCM) is a substance which undergoes simultaneous melting and solidification at certain temperature and pressure and can thereby absorb and release thermal energy. Phase change materials are also called thermal batteries which have the ability to store large amount of heat at fixed temperature. Effective integration of the latent heat thermal energy storage system with solar thermal collectors depends on heat storage materials and heat exchangers. The practical limitation of the latent heat thermal energy system for successful implementation in various applications is mainly from its low thermal conductivity. Low thermal conductivity leads to low heat transfer coefficient, and thereby, the phase change process is prolonged which signifies the requirement of heat transfer enhancement techniques. Typically, for salt hydrates and organic PCMs, the thermal conductivity range varies between 0.4–0.7 W/m K and 0.15–0.3 W/m K which increases the thermal resistance within phase change materials during operation, seriously affecting efficiency and thermal response. This paper reviews the different geometry of commercial heat exchangers that can be used to address the problem of low thermal conductivity, like use of fins, additives with high thermal conductivity materials like metal strips, microencapsulated PCM, composite PCM, porous metals, porous metal foam matrix, carbon nanofibers and nanotubes, etc. Finally, different solar thermal applications and potential PCMs for low-temperature thermal energy storage were also discussed.

This paper presents the modeling theory and results of an innovative thermal energy storage (TES) facility, ideated, realized, and tested by ENEA (Italy). This prototype enabled the thermocline storage with molten salts in a novel geometry ideated for small-medium scale decentralized solutions, which includes two vertical channels to force the circulation through two heat exchangers, respectively, and realized for charging and discharging phases (in a single tank). A thermophysical model was built and tested properly for this particular geometry in order to analyze the temperature distribution along the radius. The numerical results well reproduced the experimental values. Furthermore, the analytical solution provided a short-cut methodology able to evaluate the thermocline distribution (along the vertical axis) depending on both the time and the radius values. Hence, the influence of the radial position (r) on the thermocline degradation was studied finding that, at the edges (r → 1), the thermocline remains unchanged for longer (around ten times more) than at the center of the tank (r → 0). The obtained numerical modeling and the analytical correlation can be useful for the process analysis to scale-up the thermal storage system and to evaluate the system reliability for industrial plants.

This work aims at providing insight into developmental and operational experience of an innovative milk cooler which uses solar thermal energy for cooling of fresh milk by way of vapor absorption refrigeration system (VARS). The system uses CPC solar collector(s) producing medium temperature that is desired to provide required thermal energy to the generator of VARS. However, mismatch between the time of availability of solar energy and cooling period of milk raises a demand of integrating thermal storage to this system for use of thermal energy at appropriate times. The novelty of this work is the development of experimental setup and its operation as innovative design to meet the requirement and possible model for the industry to operate and grow using the suggested system. The design, while addressing the problem of grass root level people for generation of income, also helps in reducing the carbon footprint of milk industry, and in the world environment as a whole.

The potential of sky radiation (SR) to serve the latent space cooling loads was evaluated. Using ASHRAE standard 55 comfort limits (room temperature 22 °C, relative humidity 60%, and dew-point temperature 13.9 °C), condensation was the chosen mechanism for humidity reduction. Typical meteorological year (TMY3) weather data were used for eleven ASHRAE climate zones. Three values of load-to-radiator ratio (LRR) (infiltration/ventilation volume flow rate times the ratio of building floor area to radiator area) were evaluated: 0.35, 3.5, and 35 m/h. Three thermal storage cases were considered: 1. Annual cooling potential, 2. Diurnal storage, and 3. Minimum storage capacity to serve the entire annual load. Six SR temperatures T rad = 13.9 to −26.1 °C were tested. Even in the most challenging climates, annual SR potential exceeded the total sensible and latent cooling load, at least for the lowest LRR and the highest T rad . For diurnal storage, SR served less than 20% of the load in the hot and humid southeast, but the entire load in the mountain west. The minimum storage capacity to meet the entire annual load decreased with decreasing LRR and decreasing T rad . For the southeast, large capacity was required, but for Louisville, for instance, sufficient capacity was provided by 0.05 m 3 of water per m 2 of floor area for LRR = 0.35 m/h. These results demonstrate that for much of the U.S., sky radiation has the potential to serve the entire annual sensible and latent cooling load.

The most advanced solar thermochemical cycles in terms of demonstrated reactor efficiencies are based on temperature swing operated receiver-reactors with open porous ceria foams as a redox material. The demonstrated efficiencies are encouraging but especially for cycles based on ceria as the redox material, studies have pointed out the importance of high solid heat recovery rates to reach competitive process efficiencies. Different concepts for solid heat recovery have been proposed mainly for other types of reactors, and demonstration campaigns have shown first advances. Still, solid heat recovery remains an unsolved challenge. In this study, chances and limitations for solid heat recovery using a thermal storage unit with gas as heat transfer fluid are assessed. A numerical model for the reactor is presented and used to analyze the performance of a storage unit coupled to the reactor. The results show that such a concept could decrease the solar energy demand by up to 40% and should be further investigated.

Ca-Mn-based perovskites doped in their A- and B-site were synthesized and comparatively tested versus the Co 3 O 4 /CoO and (Mn,Fe) 2 O 3 /(Mn,Fe) 3 O 4 redox pairs with respect to thermochemical storage and oxygen pumping capability, as a function of the kind and extent of dopant. The perovskites' induced heat effects measured via differential scanning calorimetry are substantially lower: the highest reaction enthalpy recorded by the CaMnO 3– δ composition was only 14.84 kJ/kg compared to 461.1 kJ/kg for Co 3 O 4 /CoO and 161.0 kJ/kg for (Mn,Fe) 2 O 3 /(Mn,Fe) 3 O 4 . Doping of Ca with increasing content of Sr decreased these heat effects; more than 20 at % Sr eventually eliminated them. Perovskites with Sr instead of Ca in the A-site exhibited also negligible heat effects, irrespective of the kind of B site cation. On the contrary, perovskite compositions characterized by high oxygen release/uptake can operate as thermochemical oxygen pumps enhancing the performance of water/carbon dioxide splitting materials. Oxygen pumping via Ca 0.9 Sr 0.1 MnO 3– δ and SrFeO 3– δ doubled and tripled, respectively, the total oxygen absorbed by ceria during its re-oxidation versus that absorbed without their presence. Such effective pumping compositions exhibited practically no shrinkage during one heat-up/cool-down cycle. However, they demonstrated an increase of the coefficient of linear expansion due to the superposition of “chemical expansion” to thermal-only one, the effect of which on the long-term dimensional stability has to be further quantified through extended cyclic operation.

Oxide particles have potential as robust heat transfer and thermal energy storage (TES) media for concentrating solar power (CSP). Particles of low-cost, inert oxides such as alumina and/or silica offer an effective, noncorrosive means of storing sensible energy at temperatures above 1000 °C. However, for TES subsystems coupled to high-efficiency, supercritical-CO 2 cycles with low temperature differences for heat addition, the limited specific TES (in kJ kg −1 ) of inert oxides requires large mass flow rates for capture and total mass for storage. Alternatively, reactive oxides may provide higher specific energy storage (approaching 2 or more times the inert oxides) through adding endothermic reduction. Chemical energy storage through reduction can benefit from low oxygen partial pressures (P O2 ) sweep-gas flows that add complexity, cost, and balance of plant loads to the TES subsystem. This paper compares reactive oxides, with a focus on Sr-doped CaMnO 3–δ perovskites, to low-cost alumina-silica particles for energy capture and storage media in CSP applications. For solar energy capture, an indirect particle receiver based on a narrow-channel, counterflow fluidized bed provides a framework for comparing the inert and reactive particles as a heat transfer media. Low-P O2 sweep gas flows for promoting reduction impact the techno-economic viability of TES subsystems based on reactive perovskites relative to those using inert oxide particles. This paper provides insights as to when reactive perovskites may be advantageous for TES subsystems in next-generation CSP plants.

Recent disruptions of communities due to natural hazard events such as hurricanes and earthquakes have led to increased calls for improved resiliency of the built environment. The “built environment” denotes constructed facilities such as buildings and bridges, as well as infrastructure systems such as power delivery, transportation roadways, and water utilities. “Resiliency” is defined here as the “recovery and adaptability” during and after events which disrupt civil infrastructure services. In the context of this paper, the critically important service is energy delivery, on which many other services such as communications and transportation networks depend. The robustness of the building energy supply can be significantly enhanced through on-site renewable sources such as photovoltaic panels coupled with storage batteries. The degree to which the energy demand is met by the on-site capacity in the future will be determined largely upon advances in renewable energy generation and storage as well as in efficiency gains for commonly used equipment and appliances such as lighting fixtures and cooling systems. In this paper, we propose an improved design approach for the energy capacity of existing and new buildings as part of a greater regional community in which the total energy capacity requirements are met through increasingly enhanced on-site permanent power links, as opposed to increased reliance on the existing power grid. The metrics for characterizing resiliency will be “robustness,” “redundancy,” “resourcefulness,” and “rapidity,” with the associated metrics for sustainability being self-reliance and intergenerational equity enhancement.

Thermal storage plays a major role in a wide variety of industrial, commercial, and residential applications when there is a mismatch between the offer and the claim of energy. In this paper, we study numerically the contribution of phase change materials (PCMs) for solar thermal energy storage (TES) in buildings. The studied configuration is a plane solar collector incorporating a PCM layer and coupled to a concrete slab (a roof of a building). The study is conducted for Casablanca (Morocco) meteorological conditions. Several simulations were performed to optimize the melting temperature and the PCM layer thickness. The results show that PCM imposes, on the roof, a temperature close to its melting temperature. The choice of a melting temperature T melt = 22 °C (the local indoor temperature T c is fixed as T c = 22 °C) limits the losses through the concrete slab, considerably. This last seems to be, nearly, adiabatic, in this case. Also, the energy released by PCM solidification, overnight, increases the outlet temperature of the coolant fluid to 35 °C and the useful flux to 80 W/m 2 , increasing the efficiency of the solar collector by night. The PCM functioned both as an energy storage material for the stabilization of the coolant fluid temperature and as an insulating material for the building.

A major advantage of concentrating solar power (CSP) plants is their ability to store thermal energy at a cost far lower than that of current battery technologies. A recent techno-economic study found that packed rock bed thermal storage systems can be constructed with capital costs of less than 10 United States dollar (USD)/kWh t , significantly cheaper than the two-tank molten salt thermal storage currently used in CSP plants (about 22–30 USD/kWh t ). However, little work has been published on determining optimum rock bed design parameters in the context of a CSP plant. The parametric study in this paper is intended to provide an overview of the bed flow lengths, particle sizes, mass fluxes, and Biot numbers which are expected to minimize the levelized cost of electricity (LCOE) for a central receiver CSP plant with a nominal storage capacity of 12 h. The findings show that rock diameters of 20–25 mm will usually give LCOE values at or very close to the minimum LCOE for the combined rock bed and CSP plant. Biot numbers between 0.1 and 0.2 are shown to have little influence on the position of the optimum (with respect to particle diameter) for all practical purposes. Optimum bed lengths are dependent on the Biot number and range between 3 and 10 m for a particle diameter of 20 mm.

Solar combi-storages are used in many countries for storing solar heat for space heating and domestic hot water (DHW) in one device. When a combi-storage is used in combination with a heat pump, the temperature stratification efficiency of the storage is a decisive factor for the overall efficiency and thus, for the consumed end-energy of the system. In particular, fluid that is entering the storage with a high velocity may cause considerable mixing, thus, destroying stratification and leading to poor system performance. This work presents computational fluid dynamics (CFD) simulations of direct horizontal inlets at midheight of a typical solar combi-storage of about 800 L volume. Different inlet diffusor designs were simulated, and laboratory measurements were used to validate CFD experiments. For the given tank geometry, mass flow rates, and inlet position, it is found for a fluid inlet temperature of 30 °C that fluid velocities should be below 0.1 m/s and Reynolds numbers below 3000–5000 at the outlet of the diffusor in order to avoid the disturbance of a hotter 50 °C zone above the inlet. Furthermore, the fluid path within the diffusor must exceed a minimum length that corresponds to three to four times the hydraulic diameter of the diffusor.

This paper evaluates cost and performance tradeoffs of alternative supercritical carbon dioxide (s-CO 2 ) closed-loop Brayton cycle configurations with a concentrated solar heat source. Alternative s-CO 2 power cycle configurations include simple, recompression, cascaded, and partial cooling cycles. Results show that the simple closed-loop Brayton cycle yielded the lowest power-block component costs while allowing variable temperature differentials across the s-CO 2 heating source, depending on the level of recuperation. Lower temperature differentials led to higher sensible storage costs, but cycle configurations with lower temperature differentials (higher recuperation) yielded higher cycle efficiencies and lower solar collector and receiver costs. The cycles with higher efficiencies (simple recuperated, recompression, and partial cooling) yielded the lowest overall solar and power-block component costs for a prescribed power output.

This study investigates the efficiency of application of phase change materials (PCMs) in a solar cooling system. The proposed system consists of an adsorption chiller and a latent heat storage unit (LHSU) containing PCMs. The PCM stores solar energy during daytime and at nighttime, the thermal energy stored in the PCM is utilized to drive the adsorption chiller. An auxiliary heater is also used to provide the required energy in addition to the LHSU. To verify the accuracy of the obtained results, the modeling of the solar adsorption system and the PCM unit are validated separately. Moreover, the whole system performance is verified by evaluation of the conservation of energy in the system. The performance of the system is compared with a similar solar adsorption chiller lacking LHSU. Also, the parameters which affect the performance of the LHSU are studied. It is found that application of LHSU decreases auxiliary energy consumption and increases solar fraction. Solar fraction goes up more if larger amount of PCM is used. However, there exists a maximum mass of PCM which can be charged during the sunshine hours. The maximum chargeable mass of PCM goes up by increasing the solar collector area, which leads to decreasing auxiliary energy consumption and increasing solar fraction. The results also show that enlargement of the hot water storage tank reduces auxiliary energy consumption and enhances solar fraction, but decreases thermal storage efficiency. In order to achieve higher thermal storage efficiency and also less auxiliary energy consumption, it is suggested to use average-sized hot water storage tanks.

Solar cooling systems might represent a viable alternative for space cooling in residential buildings because the peak of cooling demand matches the availability of solar radiation. The use of adsorption chillers in this field gives another environmental benefit, since they employ natural refrigerants as water. However, the design of such systems is critical because it relates to several parameters and cannot be easily accomplished using traditional tools. In this work, a dynamic model for the simulation of a small solar cooling system employing adsorption chillers has been evaluated. The model, realized with the commercial software trnsys , has been implemented to quantify the effect of different operational and design parameters on the overall performances of solar cooling systems in three different Italian cities (Milan, Rome, and Messina). Particular focus was put on the comparison of different heat rejection systems, which was found to be a critical aspect in the design of such systems. In addition, an economic analysis has been performed for an optimized system, in order to evaluate the payback time of the systems compared to a traditional air conditioning system and provide indication on the possible outlooks by means of a sensitivity analysis.

The numerical simulation, design, and construction of a double glazed integrated collector storage (ICS) with compound parabolic concentrators (CPC) reflectors are presented. The design of the double glazing is optimized by means of numerical simulations under Tunisian climatic conditions. The numerical program used for the simulation consists on the transient resolution of the balance energy equations of each component of the solar water heater. Different proposed models of a double glazing are studied and compared with a reference case of a single glass ICS model. The simulation results have shown that the use of double glazing with argon layer and low-e coated lower glass instead of one glass cover significantly improves the thermal behavior of the ICS heater and visibly reduces its thermal losses during night. Taking into account these numerical results, a double-glazing ICS prototype-collector is constructed. The details of the construction, geometry, optical properties, and dimensions of the prototype are presented.

This paper describes a methodology to evaluate the storage capacity that should support a photo-voltaic (PV) power plant in order to reduce the power imbalance generated by the forecast error. This is obtained through a probabilistic analysis performed on an ensemble of synthetic data. The synthetic data signals are generated starting from at least 1 year of measured data and reproduce the same statistical distribution and the same Fourier power spectrum (FPS) shape.

A concentrated solar power (CSP) plant typically has thermal energy storage (TES), which offers advantages of extended operation and power dispatch. Using dual-media, TES can be cost-effective because of the reduced use of heat transfer fluid (HTF), usually an expensive material. The focus of this paper is on the effect of a start-up period thermal storage strategy to the cumulative electrical energy output of a CSP plant. Two strategies—starting with a cold storage tank (referred to as “cold start”) and starting with a fully charged storage tank (referred to as “hot start”)—were investigated with regards to their effects on electrical energy production in the same period of operation. An enthalpy-based 1D transient model for energy storage and temperature variation in solid filler material and HTF was applied for both the sensible heat storage system (SHSS) and the latent heat storage system (LHSS). The analysis was conducted for a CSP plant with an electrical power output of 60 MWe. It was found that the cold start is beneficial for both the SHSS and LHSS systems due to the overall larger electrical energy output over the same number of days compared to that of the hot start. The results are expected to be helpful for planning the start-up operation of a CSP plant with a dual-media thermal storage system.

Hybrid energy systems normally comprise photovoltaic (PV) modules, diesel generator, a DC–DC converter with maximum power point tracking (MPPT) control, a DC–AC inverter with pulse width modulation (PWM) controller and storage system. In this paper, interleaved converter with an hybrid perturb and observe (P&O) fuzzy MPPT technique was proposed to enhance the effectiveness of the hybrid system. The enactment of unipolar sinusoidal pulse width modulation (SPWM) technique and proportional integral (PI) controller enhances the performance of bidirectional H-bridge inverter by getting rid of lower order harmonics, which leads to least possible switching losses, thus improves the inverter efficiency.