The Riyadh Techno Valley Solar Tower, an innovative type of concentrator solar power plant, is being developed by King Saud University (KSU) and Georgia Tech (GT). The facility is being constructed at the Riyadh Techno Valley development near the KSU campus and will store thermal energy collected from the sun in solid particles, which can be heated to higher temperatures than is currently possible using molten salts. The particles must be well insulated to stop energy loss to the environment. Hence, GT and KSU have incorporated an insulated storage bin into the plant design. The bin will be constructed in several layers: an inner layer of firebrick, which can endure direct exposure to the heated particles; a specially prepared refractory insulating concrete, which maintains good insulating value at high temperatures; and a conventional structural concrete shell surrounding the entire bin. This paper presents a thermal analysis of this storage device and discusses structural analyses. Simplified analytical solutions are compared with the finite element results from a 3D ANSYS model of the entire bin. A temperature distribution is obtained, and heat loss through the bin is also evaluated. Modeling of rebar and concrete cracking are described, and methods of reducing stress on the outer concrete shell are considered. Structural support for an access tunnel into the bin is also explored. The current tunnel design involves a material with a relatively high thermal conductivity, necessitating modifications to the bin. Finally, material selection is considered, particularly with regard to the insulating concrete layer. Limitations on the use of Portland cement based insulating concretes are discussed, and alternative base materials are evaluated.

One increasingly viable option for high temperature concentrator solar power (CSP) is a central receiver system with a particle heating receiver (PHR). A PHR system uses suitable particulates to capture and store energy. It is expected that the particles will be sustained at high temperatures (in the range of 300°C or 400°C to 700°C or 800°C or even 1000°C) on most typical days of plant operation, so there is interest in how the particle optical properties might change after prolonged high-temperature exposure. This paper presents the results from experiments conducted over a 5-month period in which samples of various types of particulates including silica sands and alumina proppants were exposed to high temperatures for extended periods of time. The reflectance of a bed of particles was measured at room temperature in 8 wavelength bands using the 410-Solar reflectometer device developed by Surface Optics Corporation. The infrared emittance was determined using the ETS-100 emissometer instrument, also developed by Surface Optics Corporation [1,2]. Particles were heated to 950°C and 350°C, and measurements were recorded at intervals during the exposure so that trends in the optical properties over time could be observed. From the measured data, the total solar absorptance and total hemispherical emittance at high temperature were computed; these results are also presented.

The advantages of high temperature central receiver particle heating solar heat supply systems in concentrator solar power (CSP) have been recognized in recent years. The use of particulate as the collection medium provides two critical advantages: (1) Ordinary particulate minerals and products will allow higher collection temperatures approaching 1000°C compared with conventional molten salts, which are limited to around 650°C, and (2) the low cost high temperature particulate material can also be used as the storage medium in a highly cost effective thermal energy storage (TES) system. The high operating temperature allows use of high efficiency power conversion systems such as supercritical steam in a vapor power cycle or supercritical carbon dioxide in a Brayton cycle. Alternatively, a lower cost gas turbine can be used for the power conversion system. High conversion efficiency combined with inexpensive TES will yield a highly cost effective CSP system. The 300 kW-th prototype is being constructed as a solar heat supply system only, deferring the power conversion system for later demonstration in a larger integrated CSP system. This paper describes the general design and development efforts leading to construction of the 300 kW prototype system located in the Riyadh Techno Valley development near King Saud University in Riyadh, Saudi Arabia, which is the first sizeable solar heat supply system purposely designed, and constructed as a particle heating system. An important component in a particle heating system is the particle heating receiver (PHR), which should be durable and efficient while remaining cost-effective. A critical enabling technology of the PHR being implemented for this project was invented by researchers on our team. In our version of the PHR, the particulate flows downwards through a porous or mesh structure where the concentrated solar energy is absorbed. The porous structure will reduce the speed of the falling particulate material allowing a large temperature rise on a single pass. The new design will also increase the absorption of solar energy and mitigate convective heat loss and particle loss. Other innovative aspects of this design include low cost thermal energy storage bins and a cost effective particle to working fluid heat exchanger. Certain features of these design elements are subjects of ongoing patent applications. Nevertheless, the overall design and the development process of the prototype system is presented in this paper.