This study aims to investigate the creep buckling behavior of a stainless steel column under axial compressive loading at extremely high temperatures. Creep buckling failure time of a slender column with a rectangular cross section was experimentally measured under three different temperature conditions, namely, 800, 900, and 1000 °C. At each temperature, axial compressive loads with magnitudes ranging between 15% and 80% of the buckling loads were applied to the top of the column, and the creep buckling failure time was measured to examine its relationship with the compressive load. The stainless steel column was found to fail within a relatively short time compared to that of creep deformation under tensile loading. An increase in the temperature of the column was found to accelerate creep buckling failure. The in-plane and out-of-plane column displacements, which respectively, corresponded to the axial and lateral displacements, were monitored during the entire experiment. The creep buckling behavior of the column was also visualized by a high-speed camera. Based on the Larson–Miller parameters (LMP) determined from the experimental results, an empirical correlation for predicting the creep buckling failure time was developed. Another empirical correlation for predicting the creep buckling failure time based on the lateral deflection rate was also derived.
Skip Nav Destination
Article navigation
February 2017
Research-Article
Experimental Investigation Into Creep Buckling of a Stainless Steel Plate Column Under Axial Compression at Extremely High Temperatures
Byeongnam Jo,
Byeongnam Jo
Nuclear Professional School,
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: jo@vis.t.u-tokyo.ac.jp
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: jo@vis.t.u-tokyo.ac.jp
Search for other works by this author on:
Koji Okamoto
Koji Okamoto
Nuclear Professional School,
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: okamoto@n.t.u-tokyo.ac.jp
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: okamoto@n.t.u-tokyo.ac.jp
Search for other works by this author on:
Byeongnam Jo
Nuclear Professional School,
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: jo@vis.t.u-tokyo.ac.jp
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: jo@vis.t.u-tokyo.ac.jp
Koji Okamoto
Nuclear Professional School,
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: okamoto@n.t.u-tokyo.ac.jp
The University of Tokyo,
2-22 Shirakata,
Tokai-mura, Ibaraki 319-1188, Japan
e-mail: okamoto@n.t.u-tokyo.ac.jp
1Corresponding author.
Contributed by the Pressure Vessel and Piping Division of ASME for publication in the JOURNAL OF PRESSURE VESSEL TECHNOLOGY. Manuscript received February 12, 2016; final manuscript received March 18, 2016; published online August 5, 2016. Assoc. Editor: Haofeng Chen.
J. Pressure Vessel Technol. Feb 2017, 139(1): 011406 (8 pages)
Published Online: August 5, 2016
Article history
Received:
February 12, 2016
Revised:
March 18, 2016
Citation
Jo, B., and Okamoto, K. (August 5, 2016). "Experimental Investigation Into Creep Buckling of a Stainless Steel Plate Column Under Axial Compression at Extremely High Temperatures." ASME. J. Pressure Vessel Technol. February 2017; 139(1): 011406. https://doi.org/10.1115/1.4033155
Download citation file:
Get Email Alerts
Cited By
The Behaviour of Elbow Elements at Pure Bending Applications Compared to Beam and Shell Element models
J. Pressure Vessel Technol
Measurement of Steam-Generator-Tube Vibration Damping Caused by Anti-Vibration-Bar Supports
J. Pressure Vessel Technol (February 2025)
Related Articles
A Phenomenological Model for Intergranular Failure by r-type and Wedge-Type Cavitation
J. Eng. Mater. Technol (July,1995)
An Investigation of Thermal-Stress Fatigue as Related to High-Temperature Piping Flexibility
Trans. ASME (October,1957)
Comparative Study on Reactor Pressure Vessel Failure Behaviors With Various Geometric Discontinuities Under Severe Accident
J. Pressure Vessel Technol (April,2017)
Characterization of Tensile and Compressive Behavior of Microscale Sheet Metals Using a Transparent Microwedge Device
J. Manuf. Sci. Eng (December,2011)
Related Proceedings Papers
Related Chapters
Nuclear Components Operating in the Creep Regime
Analysis of ASME Boiler, Pressure Vessel, and Nuclear Components in the Creep Range
Members in Compression
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range
Basic Concepts
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range