Abstract

A nonlinear model is proposed for studying the effect of the eccentricity of applied tensile forces on the clamp load loss in bolted joints that were initially tightened beyond the bolt elastic limit while the joint remained in the elastic range. A closed form solution is obtained for the amount of clamp load loss due to a cyclic separating force. The proposed model takes into account two sources of nonlinearity, namely, the strain hardening behavior of the yielded bolt material as well as the nonlinear deformation behavior of the clamped plates under an external separating load. After the initial tightening of the fastener past its elastic limit, the subsequent application of a tensile separating force on the joint tends to increase the fastener tension in a nonlinear fashion, and, simultaneously, reduce the clamping force in the bolted joint from its initial value. Upon the removal of the cyclic tensile load, the bolted joint system reaches a new equilibrium point between the residual fastener tension and the joint clamping force. At the new equilibrium point, the fastener tension is reduced from its preload due to its plastic elongation; simultaneously, a partial yet permanent loss in the clamp load level takes place. Excessive clamp load loss may lead to joint leakage, fastener loosening, or fatigue failure. For a known amplitude of the external cyclic tensile load, the increase in bolt tension and corresponding reduction in the joint clamp load are highly sensitive to the eccentricity of the tensile load (from the bolt center). Variables studied include the eccentricity value of the separating load, rate of strain hardening of the bolt material, compressive and tensile stiffness of the clamped plates, bolt stiffness, bolt preload, and magnitude of the separating tensile load.

1.
Sawa
,
T.
, and
Maruyama
,
K.
, 1977, “
Force Ratio of Bolted Joints: The Case Where Clamped Parts Are Hollow Cylinders
,”
Bull. JSME
0021-3764,
20
, pp.
141
150
.
2.
Bickford
,
J. H.
, 1997,
An Introduction to the Design and Analysis of Bolted Joints
, 3rd ed.,
Marcel Dekker
,
New York, NY
.
3.
Bickford
,
J. H.
, and
Nassar
,
S.
, 1998,
Handbook of Bolts and Bolted Joints
,
Marcel Dekker
,
New York, NY
.
4.
Nassar
,
S. A.
,
Barber
,
G. C.
, and
Zuo
,
D.
, 2005, “
Bearing Friction Torque in Bolted Joints
,”
STLE Tribol. Trans.
1040-2004,
48
, pp.
69
75
.
5.
Chapman
,
I.
,
Newham
,
J.
, and
Wallace
,
P.
, 1986, “
The Tightening of Bolts to Yield and Their Performance Under Load
,”
Trans. ASME, J. Vib., Acoust., Stress, Reliab. Des.
0739-3717,
108
, pp.
213
221
.
6.
Juvinall
,
R. C.
, and
Marshek
,
K. M.
, 2000,
Fundamentals of Machine Component Design
, 3rd ed.,
Wiley
,
New York
.
7.
Grosse
,
R. I.
, and
Mitchell
,
L. D.
, 1990, “
Nonlinear Axial Stiffness Characteristics of Axisymmetric Bolted Joints
,”
ASME J. Mech. Des.
0161-8458,
112
, pp.
442
449
.
8.
Nassar
,
S. A.
, and
Shoberg
,
R. S.
, 1992, “
Effect of Fastener Tightening Beyond Yield on the Behavior of Joints Under Service Loads
,”
Proceedings of the 18th Annual Conference of the AMSE
, Michigan State University, East Lansing, pp.
1
17
.
9.
Nassar
,
S. A.
, and
Matin
,
P. H.
, 2004, “
Fastener Tightening Beyond Yield
,”
Proceedings of the ASME Pressure Vessels and Piping Conference
, San Diego, CA, Jul. 25–29, pp.
29
40
.
10.
Nassar
,
S. A.
, and
Matin
,
P. H.
, 2006, “
Clamp Load Loss Due to Fastener Elongation Beyond Its Elastic Limit
,”
ASME J. Pressure Vessel Technol.
0094-9930,
128
, pp.
379
387
.
11.
Nassar
,
S. A.
, and
Matin
,
P. H.
, 2006, “
Nonlinear Strain Hardening Model for Predicting Clamp Load Loss in Bolted Joints
,”
ASME J. Mech. Des.
0161-8458,
128
, pp.
1328
1336
.
12.
Nassar
,
S. A.
,
Yang
,
X.
,
Gandham
,
S.
, and
Wu
,
Z.
, 2011, “
Nonlinear Deformation Behavior of Clamped Bolted Joints Under a Separating Service Load
,”
ASME J. Pressure Vessel Technol.
0094-9930,
133
, p.
021001
.
13.
Cook
,
R. D.
, and
Young
,
W. C.
, 1985,
Advanced Mechanics of Materials
,
Macmillan
,
New York
.
14.
Juvinall
,
R. C.
, 1967,
Engineering Considerations of Stress, Strain, and Strength
,
McGraw-Hill
,
New York
.
You do not currently have access to this content.