Based on the time-driven discrete element method, granular flow within a hopper is investigated. The main focus is thereby set on hopper vessel design variables such as discharge rates and applied wall pressures. Within the used model contacts are assumed as linear viscoelastic in normal and frictional-elastic in tangential direction. The hopper geometry is chosen according to Yang and Hsiau (2001, “The Simulation and Experimental Study of Granular Materials Discharged From a Silo With the Placement of Inserts,” Powder Technol., 120(3), pp. 244–255), who performed both experimental and numerical investigations. The considered setup is attractive because it involves only a small number of particles enabling fast modeling. However, the results on the experimental flow rates reported are contradictory and are afflicted with errors. By an analysis of the hopper fill levels at different points of time, the correct average discharge times and flow rates are obtained. Own simulation results are in good agreement with the experimental flow rates and discharge times determined. Based on the thereby defined set of simulation parameters, a sensitivity analysis of parameters such as friction coefficients, stiffnesses, and time steps is performed. As flow properties, besides the overall discharge times, the discharge time averaged axial and radial velocity distributions within the hopper and the normal stresses on the side walls during the first seconds of discharge are considered. The results show a strong connection of the friction coefficients with the discharge times, the velocity distributions, and the stresses on the side walls. Other parameters only reveal a weak often indifferent influence on the studied flow properties.
Skip Nav Destination
Article navigation
June 2009
Research Papers
A Numerical Study on the Sensitivity of the Discrete Element Method for Hopper Discharge
H. Kruggel-Emden,
H. Kruggel-Emden
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, Germany
Search for other works by this author on:
S. Rickelt,
S. Rickelt
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, Germany
Search for other works by this author on:
S. Wirtz,
S. Wirtz
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, Germany
Search for other works by this author on:
V. Scherer
V. Scherer
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, Germany
Search for other works by this author on:
H. Kruggel-Emden
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, Germany
S. Rickelt
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, Germany
S. Wirtz
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, Germany
V. Scherer
Department of Energy Plant Technology,
Ruhr-Universitaet Bochum
, Universitaetsstrasse 150, D-44780 Bochum, GermanyJ. Pressure Vessel Technol. Jun 2009, 131(3): 031211 (10 pages)
Published Online: April 29, 2009
Article history
Received:
December 7, 2007
Revised:
July 15, 2008
Published:
April 29, 2009
Citation
Kruggel-Emden, H., Rickelt, S., Wirtz, S., and Scherer, V. (April 29, 2009). "A Numerical Study on the Sensitivity of the Discrete Element Method for Hopper Discharge." ASME. J. Pressure Vessel Technol. June 2009; 131(3): 031211. https://doi.org/10.1115/1.3122022
Download citation file:
Get Email Alerts
Measurement of Steam-Generator-Tube Vibration Damping Caused by Anti-Vibration-Bar Supports
J. Pressure Vessel Technol (February 2025)
Surface Strain Measurement for Non-Intrusive Internal Pressure Evaluation of a Cannon
J. Pressure Vessel Technol (December 2024)
Dynamic Response and Damage Analysis of a Large Steel Tank Impacted by an Explosive Fragment
J. Pressure Vessel Technol (February 2025)
Related Articles
Toward the Development of a Verification, Validation, and Uncertainty Quantification Framework for Granular and Multiphase Flows—Part 1: Screening Study and Sensitivity Analysis
J. Verif. Valid. Uncert (September,2018)
Coupling Continuous and Discontinuous Descriptions to Model First Body Deformation in Third Body Flows
J. Tribol (October,2011)
Multibody Dynamic Model of Web Guiding System With Moving Web
J. Dyn. Sys., Meas., Control (September,2010)
Method for Sensitivity Analysis of Resonance Forced Response of Bladed Disks With Nonlinear Contact Interfaces
J. Eng. Gas Turbines Power (March,2009)
Related Proceedings Papers
Related Chapters
Incremental Model Adjustment
Nonlinear Regression Modeling for Engineering Applications: Modeling, Model Validation, and Enabling Design of Experiments
Sensitivity Analysis of Zwart-Gerber-Belamri Model Parameters on the Numerical Simulation of Francis Runner Cavitation
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
A Smart Sampling Strategy for One-at-a-Time Sensitivity Experiments (PSAM-0360)
Proceedings of the Eighth International Conference on Probabilistic Safety Assessment & Management (PSAM)