An experimental study has been conducted to evaluate the effect of roller expansion of heat exchanger tubes in enlarged tubesheet holes on joint strength, tube wall reduction (i.e., thinning), and strain hardening of the tubes and surrounding tubesheet ligaments. Different levels of tube-to-tubesheet hole clearance, or overtolerance (OT), were investigated to simulate tubesheet in-service, and during-maintenance, hole enlargement process. The experimental results have shown that, in spite of increasing overtolerance level by up to seven times the maximum value allowed by the Tubular Exchanger Manufacturer Association (TEMA) standard, the average strength of the test joints has not declined below the strength of joints in the allowed TEMA OT range. Percent wall reduction (WR) of the expanded tube was found to increase linearly with increasing overtolerance value; although its maximum value remained well below the wall reduction limit for which a joint is rejected in industry. An observed increase in hardness of the expanded tube material is evidence of the high degree of strain hardening to which the expanded tubes are subjected compared with the surrounding ligaments. Pull-out forces, calculated using existing analytical methods, were found to compare well with the experimental results.

Issue Section:
Technical Papers
Keywords:
heat exchangers, joining processes, pressure vessels, mechanical properties, hardening, stress-strain relations
Topics:
Clearances (Engineering), Heat exchangers, Rollers, Work hardening, Maintenance
1.
Yokell, S., 1991, “Expanded and Welded-and-Expanded Tube-to-Tube Sheet Joints,” TEMA Technical Committee Meeting, San Francisco, CA.
2.
Yokell
,
S.
,
1992
, “
Expanded and Welded-and-Expanded Tube-to-Tubesheet Joints
,”
ASME J. Pressure Vessel Technol.
,
114
, pp.
157
–
165
.
3.
Kohlpaintner
,
W. R.
,
1995
, “
Calculation of Hydraulically Expanded Tube-to Tubesheet Joints
,”
ASME J. Pressure Vessel Technol.
,
117
, pp.
24
–
30
.
4.
Openheimer, P., 1926, “Ueber Das Einwalzen und Einpressen Von Rohren in Kesselwaende,” Ph.D. thesis, Technical University of Munich.
5.
Jantscha, R., 1929, “Ueber Das Einwalzen und Einpressen von Kesselund Ueberhetzrrohren bei Verwedung vershcheidener Werkstoffe.” Ph.D. thesis, Technical University of Darmstadt.
6.
Jawad
,
M. H.
,
Clarkin
,
E. J.
, and
Schuessler
,
R. E.
,
1987
, “
Evaluation of Tube-to-Tubesheet Junctions
,”
ASME J. Pressure Vessel Technol.
,
109
, pp.
19
–
26
.
7.
Goodier, J. N., and Schoessow, G. J., 1943, “The Holding Power and Hydraulic Tightness of Expanded Tube Joints: Analysis of the Stress and Deformation,” Trans. ASME, July.
8.
Nadai, A., 1943, “Theory of the Expanding Boiler and Condenser Tube Joints Through Rolling,” Trans. ASME, Nov.
9.
Wilson, R. M., 1978, “The Elastic-Plastic Behavior of a Tube During Expansion,” ASME Paper No. 78-PVP-112.
10.
Chaaban
,
A.
,
Ma
,
H.
, and
Bazergui
,
A.
,
1992
, “
Tube-Tubesheet Joint: A Proposed Equation for the Equivalent Sleeve Diameter Used in the Single Tube Model
,”
ASME J. Pressure Vessel Technol.
,
114
,
19
19
.
11.
Allam
,
M.
,
Chaaban
,
A.
, and
Bazergui
,
A.
,
1998
, “
Estimation of Residual Stresses in Hydraulically Expanded Tube-Tubesheet Joints
,”
ASME J. Pressure Vessel Technol.
,
120
, pp.
129
129
.
12.
Allam, M., A. Bazergui, and A. Chaaban, 1998b, “The Effect of Tube Strain Hardening Level on the Residual Stresses of Hydraulically Expanded Tube-to-Tubesheet Joint,” ASME PVP Vol. 373, Fatigue, Fracture, and Residual Stresses, pp. 447–455.
13.
Grimison
,
E.
, and
Lee
,
G.
, 1943, “Experimental Investigation of Tube Expanding,” Trans. ASME, July, 497.
14.
Fisher
,
F. F.
, and
Brown
,
G. J.
, 1954, “Tube Expanding and Related Subjects,” Trans. ASME, May, 563–575.
15.
Sang
,
Z. F.
,
Zhu
,
Y. Z.
, and
Widera
,
G. E. O.
,
1996
, “
Reliability Factors and Tightness of Tube-to-Tubesheet Joints
,”
ASME J. Pressure Vessel Technol.
,
118
,
137
–
141
.
16.
Appendix A. ASME Boiler and Pressure Vessel Code, 1986, Section VIII, Division 1, American Society of Mechanical Engineering, pp. 575–580.
17.
Standards for the Tubular Exchanger Manufacturers Association, 1988, 7th Edition, TEMA, Tarrytown, New York, NY.
18.
Mitra, A., 1998, Fundamentals of Quality Control and Improvement, 2nd Edition, Chap. 4. Prentice–Hall, Inc., New Jersey, pp. 173–193.
19.
Pettersson, C. O., and Holmquist, M., 1996, “Tube-to-Tubesheet Welding and Expansion of the Super Duplex Steel SAF 2507 (UNS S32750) at the Fabrication of Heat Exchangers,” Stainless Steels Int. Congress, June, pp. 184–191.
Copyright © 2003
 by ASME
You do not currently have access to this content.