Exoskeletons can assist wearers to relearn natural movements when attached to the human body. However, most current devices are bulky and heavy, which limit their application. In this paper, we integrated type and dimensional synthesis to design one degree-of-freedom (DOF) linkages consisting of only revolute joints with multiple output joints for compact exoskeletons. Type synthesis starts from a four-bar linkage where the output link generates the first angular output. Then, an RRR dyad is connected to the four-bar linkage for the second angular output while ensuring that the overall DOF of the new mechanism is 1. A third output joint is added in a similar manner. During each step, dimensional synthesis is formulated as a constrained optimization problem and solved via genetic algorithms. In the first case study, we developed a finger exoskeleton based on a 10-bar-13-joint linkage for a natural curling motion. The second case study presents a leg exoskeleton based on an 8-bar-10-joint linkage to reproduce a natural walking gait at the hip and knee joints. We manufactured the exoskeletons to validate the proposed approach.
Skip Nav Destination
Article navigation
September 2018
Research-Article
An Integrated Type and Dimensional Synthesis Method to Design One Degree-of-Freedom Planar Linkages With Only Revolute Joints for Exoskeletons
Zefang Shen,
Zefang Shen
Department of Mechanical Engineering,
Curtin University,
Perth, WA 6102
e-mail: Zefang.shen@postgrad.curtin.edu.au
Curtin University,
Perth, WA 6102
e-mail: Zefang.shen@postgrad.curtin.edu.au
Search for other works by this author on:
Lei Cui
Lei Cui
Search for other works by this author on:
Zefang Shen
Department of Mechanical Engineering,
Curtin University,
Perth, WA 6102
e-mail: Zefang.shen@postgrad.curtin.edu.au
Curtin University,
Perth, WA 6102
e-mail: Zefang.shen@postgrad.curtin.edu.au
Garry Allison
Lei Cui
1Corresponding author.
Contributed by the Mechanisms and Robotics Committee of ASME for publication in the JOURNAL OF MECHANICAL DESIGN. Manuscript received January 5, 2018; final manuscript received May 24, 2018; published online June 22, 2018. Assoc. Editor: Ettore Pennestri.
J. Mech. Des. Sep 2018, 140(9): 092302 (12 pages)
Published Online: June 22, 2018
Article history
Received:
January 5, 2018
Revised:
May 24, 2018
Citation
Shen, Z., Allison, G., and Cui, L. (June 22, 2018). "An Integrated Type and Dimensional Synthesis Method to Design One Degree-of-Freedom Planar Linkages With Only Revolute Joints for Exoskeletons." ASME. J. Mech. Des. September 2018; 140(9): 092302. https://doi.org/10.1115/1.4040486
Download citation file:
Get Email Alerts
Multi-Split Configuration Design for Fluid-Based Thermal Management Systems
J. Mech. Des (February 2025)
Related Articles
Synthesis of Quasi-Constant Transmission Ratio Planar Linkages
J. Mech. Des (October,2015)
Overconstrained Mechanisms Derived From RPRP Loops
J. Mech. Des (June,2018)
Design and Kinematic Analysis of a Novel Deployable Antenna Mechanism for Synthetic Aperture Radar Satellites
J. Mech. Des (November,2022)
Related Proceedings Papers
Related Chapters
Exoskeletons and Bipeds
Designs and Prototypes of Mobile Robots
Introduction
Chitosan and Its Derivatives as Promising Drug Delivery Carriers
Piping Design
Power Boilers: A Guide to the Section I of the ASME Boiler and Pressure Vessel Code, Second Edition