In this paper the design of a multi-finger force-reflecting haptic interface device for teleoperational grasping is introduced. The haptic interface or “master” controller device is worn on the human operator’s hand and measured human finger positions are used to control the finger positions of a remote grasping manipulator or “slave” device. The slave may be a physical robotic grasping manipulator, or a computer generated representation of a human hand such as used in virtual reality applications. The forces measured by the robotic slave, or calculated for the virtual slave, are presented to the operator’s fingertips through the master providing a means for deeper human sensation of presence and better control of grasping tasks in the slave environments. Design parameters and performance measures for haptic interfaces for teleoperation are discussed. One key performance issue involving the high-speed display of forces during initial contact, especially when interacting with rigid surfaces, is addressed by the present design, reducing slave controller computation requirements and overcoming actuator response time constraints. The design presented utilizes a planar four-bar linkage for each finger, to represent each finger bend motion as a single degree of freedom, and to provide a finger bend resistance force that is substantially perpendicular to the distal finger pad throughout the full 180 degrees of finger bend motion represented. The finger linkage design, in combination with a remote position measurement and force display assembly, provides a very lightweight and low inertia system with a large workspace. The concept of a replicated finger is introduced which, in combination with a decoupled actuator and feed forward control, provides improved performance in transparent free motion, and rapid, stable touch sensation of initial contact with rigid surfaces. A distributed computation architecture with a PC based haptic interface controller and associated control algorithms are also discussed.
Skip Nav Destination
Article navigation
June 2002
Technical Papers
Design and Control of a Force-Reflecting Haptic Interface for Teleoperational Grasping
Scott L. Springer,
Scott L. Springer
University of Wisconsin–Stout, Department of Technology, P.O. Box 790, Menomonie, Wisconsin 54751
Search for other works by this author on:
Nicola J. Ferrier
Nicola J. Ferrier
University of Wisconsin–Madison, Department of Mechanical Engineering, 1513 University Avenue, Madison, Wisconsin 53706
Search for other works by this author on:
Scott L. Springer
University of Wisconsin–Stout, Department of Technology, P.O. Box 790, Menomonie, Wisconsin 54751
Nicola J. Ferrier
University of Wisconsin–Madison, Department of Mechanical Engineering, 1513 University Avenue, Madison, Wisconsin 53706
Contributed by the Mechanisms Committee for publication in the JOURNAL OF MECHANICAL DESIGN. Manuscript received Jan. 2000. Associate Editor: G. S. Chirikjian.
J. Mech. Des. Jun 2002, 124(2): 277-283 (7 pages)
Published Online: May 16, 2002
Article history
Received:
January 1, 2000
Online:
May 16, 2002
Citation
Springer, S. L., and Ferrier, N. J. (May 16, 2002). "Design and Control of a Force-Reflecting Haptic Interface for Teleoperational Grasping ." ASME. J. Mech. Des. June 2002; 124(2): 277–283. https://doi.org/10.1115/1.1470493
Download citation file:
Get Email Alerts
Related Articles
Performance Augmentation of Underactuated Fingers' Grasps Using Multiple Drive Actuation
J. Mechanisms Robotics (August,2017)
Design of Dissipative and Stable Assist Robots
J. Mech. Des (December,2007)
A Lyapunov Stable Controller for Bilateral Haptic Teleoperation of Single-Rod Hydraulic Actuators Subjected to Base Disturbance
J. Dyn. Sys., Meas., Control (March,2019)
Fast Control of Linear Systems Subject to Input Constraints
J. Dyn. Sys., Meas., Control (March,2000)
Related Proceedings Papers
Related Chapters
QP Based Encoder Feedback Control
Robot Manipulator Redundancy Resolution
Fault-Tolerant Control of Sensors and Actuators Applied to Wind Energy Systems
Electrical and Mechanical Fault Diagnosis in Wind Energy Conversion Systems
Analysis of Force Transmission Performance and Optimize Design of a 3DOF Parallel Haptic Device
International Conference on Information Technology and Management Engineering (ITME 2011)