In the spiral bevel and hypoid gear manufacturing industry, master gear sets are usually developed from initial machine settings obtained from computer software or instruction sheets. These initial machine settings are then modified until a satisfactory bearing pattern is obtained, a process called bearing pattern development. Once a satisfactory bearing pattern is obtained, manufacturing errors and heat treatment distorsions can be accounted for by proportionally changing the machine settings according to the results of a V-H test in which the pinion vertical and horizontal positions are modified until the bearing pattern is acceptable. Once a satisfactory combination of master pinion and gear is obtained, their actual tooth surfaces usually do not correspond to those of the initial theoretical model, and the theoretical pinion and gear surface definitions are unknown. This paper presents a computer algorithm used to identify the machine settings producing a theoretical tooth surface closest to that of a measured surface, what the authors call Surface Match, in order to effectively simulate the kinematical behavior of real gear teeth. The approach is applicable to both 1st and 2nd order surface errors, including profile deviation, for any cutting process. However, given the availability of experimental data for the Fixed Setting™, Formate™ and Helixform™ cutting processes, the examples presented in the paper are related to these cutting processes.

Issue Section:
Power Transmission and Gearing
Topics:
Machinery, Spiral bevel gears, Bearings, Cutting, Gears, Errors, Algorithms, Computer software, Computers, Gear teeth, Heat treating (Metalworking), Manufacturing, Manufacturing industry
1.
Gosselin C., Shiono Y., Nonaka T., Kubo A., “A Computer Based Approach Aimed at Reproducing Master Spiral Bevel and Hypoid Pinions and Gears,” AGMA Paper 96FTM1.
2.
Gosselin C., Cloutier L., Brousseau J., “Tooth Contact Analysis of High Conformity Spiral Bevel Gears,” JSME MPT 1991, Hiroshima.
3.
Gosselin C., Cloutier L., Nguyen Q. D., “The Influence of the Kinematical Motion Error on the Loaded Transmission Error of Spiral Bevel Gears,” AGMA Paper 92FTM10, 1992.
4.
Baxter M. L., “Exact Determination of Tooth Surfaces for Spiral Bevel and Hypoid Gears,” AGMA Paper 139.02, 1966.
5.
Litvin F. L., Zhang Y., Kieffer J., “Identification and Minimization of Deviations of Real Tooth Surfaces,” ASME Journal of Mechanical Design, Vol. 113, Mar. 1991.
6.
Krenzer T. J., “Computer Aided Corrective Machine Settings for Manufacturing Bevel and Hypoid Gears,” AGMA Paper 84FTM4, 1984.
7.
Krenzer T. J., Knebel R., “Computer Aided Inspection of Bevel and Hypoid Gears,” SAE Paper 831266, 1983.
8.
Stadtfeld H. J., “Handbook of Bevel and Hypoid Gears,” Rochester Institute of Technology, 1993.
9.
The Gleason Works, “Tooth Bearing Development on Spiral Bevel and Hypoid Gears,” SD 6083A, Sept. 1967.
10.
Litvin F. L., Zhang Y., Lundy M., “Determination of Settings of a Tilted Head Cutter for Generation of Hypoid and Spiral Bevel Gears,” 1989 ASME PTG.
11.
Zhang Y., Litvin F. L., & et al., “Computerized Analysis of Meshing and Contact of Gear Real Tooth Surfaces,” ASME Journal of Mechanical Design, Vol. 116, Sept. 1994.
12.
Remond D., Jean Y., Gosselin C., “Practical Performances in High Speed Measurement of Gear Transmission Error Using Optical Encoders,” Cancam 1997 Proceedings, p. 141, June, 1997.
This content is only available via PDF.
Copyright © 1998
 by The American Society of Mechanical Engineers
You do not currently have access to this content.