A comparison is presented between the sensitivity to measurement error of the crack compliance and layer removal methods of residual stress measurement when applied to glass fiber reinforced plastic (GFRP) pipes. This is done by adding random scatter to the exact strain distribution associated with a known stress distribution. This defines strain data that simulate experimental measurements. These data are used to determine the corresponding residual stress distributions. The error in the residual stress distribution when scatter is included can thereby be determined. It is shown that the layer removal and crack compliance methods are equally suitable for the measurement of axial and circumferential stresses in a pipe wound at only ±55 deg. The layer removal method, however, is shown to have significantly lower sensitivity to measurement error when the axial residual stresses in layered GFRP pipes are considered.

References

References
1.
Tarnopol'skii
,
Yu. M.
,
Portnov
,
G. G.
, and
Spridzans
,
Yu.
B.
,
1972
, “
Compensation of Thermal Stresses in Glass-Fiber-Reinforced Plastic Articles by the Layerwise Winding Method
,”
Polym. Mech.
,
8
(
4
), pp.
553
557
.
2.
Kim
,
J. W.
, and
Lee
,
D. G.
,
2007
, “
Measurement of Residual Stresses in Thick Composite Cylinders by the Radial-Cut-Cylinder-Bending Method
,”
Compos. Struct.
,
77
(
4
), pp.
444
456
.
3.
Seif
,
M. A.
, and
Short
,
S. R.
,
2002
, “
Determination of Residual Stresses in Thin-Walled Composite Cylinders
,”
Exp. Tech.
,
26
(
2
), pp.
43
46
.
4.
Seif
,
M. A.
,
Khashaba
,
U. A.
, and
Rojas-oviedo
,
R.
,
2007
, “
Residual Stress Measurements in CFRE and GFRE Composite Missile Shells
,”
Compos. Struct.
,
79
(
2
), pp.
261
269
.
5.
Ha
,
S. K.
,
Kim
,
H.-T.
, and
Sung
,
T.-H.
,
2003
, “
Measurement and Prediction of Process-Induced Residual Strains in Thick Wound Composite Rings
,”
J. Compos. Mater.
,
37
(
14
), pp.
1223
1237
.
6.
Ha
,
S. K.
,
Kim
,
H. T.
, and
Han
,
S. C.
,
2004
, “
Effects of Rotor Sizes and Epoxy System on the Process-Induced Residual Strains Within Multi-Ring Composite Rotors
,”
J. Compos. Mater.
,
38
(
10
), pp.
871
885
.
7.
Cheng
,
W.
, and
Finnie
,
I.
,
2007
,
Residual Stress Measurement and the Slitting Method
,
Springer
,
New York
.
8.
Prime
,
M. B.
,
1999
, “
Residual Stress Measurement by Successive Extension of a Slot: The Crack Compliance Method
,”
ASME Appl. Mech. Rev.
,
52
(
2
), pp.
75
96
.
9.
Cheng
,
W.
, and
Finnie
,
I.
,
1986
, “
Measurement of Residual Hoop Stress in Cylinders Using the Compliance Method
,”
ASME J. Eng. Mater. Technol.
,
108
(
2
), pp.
87
92
.
10.
Cheng
,
W.
, and
Finnie
,
I.
,
1985
, “
A Method for Measurement of Axisymmetric Residual Stresses in Circumferentially Welded Thin-Walled Cylinders
,”
ASME J. Eng. Mater. Technol.
,
107
(
3
), pp.
181
185
.
11.
Cheng
,
W.
,
Finnie
,
I.
, and
Vardar
,
O.
,
1992
, “
Estimation of Axisymmetric Residual Stresses in a Long Cylinder
,”
ASME J. Eng. Mater. Technol.
,
114
(
2
), pp.
137
140
.
12.
Cheng
,
W.
, and
Finnie
,
I.
,
1998
, “
The Single Slice Method for Measurement of Axisymmetric Residual Stresses in Solid Rods or Hollow Cylinders in the Region of Plane Strain
,”
ASME J. Eng. Mater. Technol.
,
120
(
2
), pp.
170
176
.
13.
Cheng
,
W.
,
2000
, “
Measurement of the Axial Residual Stresses Using the Initial Strain Approach
,”
ASME J. Eng. Mater. Technol.
,
122
(
1
), pp.
135
140
.
14.
Ganley
,
J. M.
,
Maji
,
A. K.
, and
Huybrechts
,
S.
,
2000
, “
Explaining Spring-In in Filament Wound Carbon Fibre/Epoxy Composites
,”
J. Compos. Mater.
,
34
(
14
), pp.
1216
1239
.
15.
Akbari
,
S.
,
Taheri-Behrooz
,
F.
, and
Shokrieh
,
M. M.
,
2013
, “
Slitting Measurement of Residual Hoop Stresses Through the Wall-Thickness of a Filament Wound Composite Ring
,”
Exp. Mech.
,
53
(
9
), pp.
1509
1518
.
16.
Finnie
,
S.
,
Cheng
,
W.
,
Finnie
,
I.
,
Drezet
,
J. M.
, and
Gremaud
,
M.
,
2003
, “
The Computation and Measurement of Residual Stresses in Laser Deposited Layers
,”
ASME J. Eng. Mater. Technol.
,
125
(
3
), pp.
302
308
.
17.
Prime
,
M. B.
, and
Hellwig
,
Ch.
,
1997
, “
Residual Stresses in a Bi-Material Laser Clad Measured Using Compliance
,”
Fifth International Conference on Residual Stresses
(
ICRS-5
), Linköping, Sweden, June 16–18, T. Ericsson, M. Odén, and A. Andersson, eds., Linkopings Universitet, Linköping, Sweden, Vol.
1
, pp.
127
132
.
18.
Ekbote
,
B.
,
Kwon
,
P.
, and
Prime
,
M. B.
,
2006
, “
Micromechanics-Based Design and Processing of Efficient Meso-Scale Heat Exchanger
,”
21st Annual Technical Conference of the American Society for Composites
, Dearborn, MI, Sept. 17–20, Vol. 2, pp.
978
992
.
19.
Ersoy
,
N.
, and
Vardar
,
O.
,
2000
, “
Measurement of Residual Stresses in Layered Composites by Compliance Method
,”
J. Compos. Mater.
,
34
(
7
), pp.
575
598
.
20.
Shokrieh
,
M. M.
,
Akbari
,
S.
, and
Daneshvar
,
A.
,
2013
, “
A Comparison Between the Slitting Method and the Classical Lamination Theory in Determination of Macro-Residual Stresses in Laminated Composites
,”
Compos. Struct.
,
96
, pp.
708
715
.
21.
Sachs
,
G.
,
1927
, “
The Determination of Residual Stresses in Rods and Tubes
,”
Z. Metallkunde
,
19
(
9
), pp.
352
357
.
22.
Venter
,
A. M.
,
Swardt
,
R. R.
, and
Kyriacou
,
S.
,
2000
, “
Comparative Measurements on Autofrettaged Cylinders With Large Bauschinger Reverse Yielding Zones
,”
J. Strain Anal. Eng. Des.
,
35
(
6
), pp.
495
469
.
23.
Stacey
,
A.
, and
Webster
,
G. A.
,
1988
, “
Determination of Residual Stress Distributions in Autofrettaged Tubing
,”
Int. J. Pressure Vessels Piping
,
31
(
3
), pp.
205
220
.
24.
Botros
,
B. M.
,
1960
, “
Residual Stresses in Cold Ironed Tubes
,”
Int. J. Mech. Sci.
,
2
(
3
), pp.
195
205
.
25.
Mack
,
D. R.
,
1962
, “
Measurement of Residual Stress in Disks From Turbine-Rotor Forgings
,”
Exp. Mech.
,
2
(
5
), pp.
155
158
.
26.
Terasaki
,
T.
,
Akiyama
,
T.
, and
Ishimura
,
T.
,
1995
, “
New Method for Estimating Residual Stresses in Pipe Made by Surfacing Weld
,”
ASME J. Manuf. Sci. Eng.
,
117
(
3
), pp.
365
371
.
27.
Chen
,
J.
,
Terasaki
,
T.
,
Akiyama
,
T.
, and
Kishitake
,
K.
,
2000
, “
New Concept of Equivalent Inherent Strain for Measuring Axisymmetric Residual Stresses
,”
ASME J. Manuf. Sci. Eng.
,
122
(
2
), pp.
304
309
.
28.
Olson
,
W. A.
, and
Bert
,
C. W.
,
1966
, “
Analysis of Residual Stresses in Bars and Tubes of Cylindrically Orthotropic Materials—Paper Presents Equations for Calculating Residual Stresses From Surface-Strain Data Measured After Successive Borings in a Bar or Tube Made of a Cylindrically Orthotropic Material
,”
Exp. Mech.
,
6
(
9
), pp.
451
457
.
29.
Voyiadjis
,
G. Z.
,
Kiousis
,
P. D.
, and
Hartley
,
C. S.
,
1985
, “
Analysis of Residual Stresses in Cylindrically Anisotropic Materials
,”
Exp. Mech.
,
25
(
2
), pp.
145
147
.
30.
Voyiadjis
,
G. Z.
, and
Hartley
,
C. S.
,
1987
, “
Residual-Stress Determination of Concentric Layers of Cylindrically Orthotropic Materials
,”
Exp. Mech.
,
27
(
3
), pp.
290
297
.
31.
Rasty
,
J.
,
Le
,
X.
,
Baydogan
,
M.
, and
Cárdenas-García
,
J. F.
,
2007
, “
Measurement of Residual Stresses in Nuclear-Grade Zircaloy-4(R) Tubes—Effect of Heat Treatment
,”
Exp. Mech.
,
47
(
2
), pp.
185
199
.
32.
Carpenter
,
H. W.
,
Reid
,
R. G.
, and
Paskaramoorthy
,
R.
,
2014
, “
Extension of the Layer Removal Technique for the Measurement of Residual Stresses in Layered Anisotropic Cylinders
,”
Int. J. Mech. Mater. Des.
,
10
(
3
), pp.
269
280
.
33.
Carpenter
,
H. W.
,
Reid
,
R. G.
, and
Paskaramoorthy
,
R.
,
2014
, “
Measurement of the Distribution of Residual Stresses in Layered Thick-Walled GFRP Pipes
,”
Exp. Mech.
,
54
(
9
), pp.
1627
1638
.
34.
Prime
,
M. B.
, and
Hill
,
M. R.
,
2006
, “
Uncertainty Analysis, Model Error, and Order Selection for Series-Expanded, Residual Stress Inverse Solutions
,”
ASME J. Eng. Mater. Technol.
,
128
(
2
), pp.
175
185
.
35.
Pagliaro
,
P.
, and
Prime
,
M. B.
,
2006
, “
Uncertainty, Model Error, and Improving the Accuracy of Residual Stress Inverse Solutions
,”
SEM Annual Conference and Exposition on Experimental and Applied Mechanics
, St. Louis, MO, June 4–7,
SEM
Paper No. 176, pp.
479
488
.
36.
Holman
,
J. P.
,
2012
,
Experimental Methods for Engineers
,
8th ed.
,
McGraw-Hill
,
New York
.
37.
Schajer
,
G. S.
, and
Prime
,
M. B.
,
2006
, “
Use of Inverse Solutions for Residual Stress Measurement
,”
ASME J. Eng. Mater. Technol.
,
128
(
3
), pp.
375
382
.
38.
Herakovich
,
C. T.
,
1998
,
Mechanics of Fibrous Composites
,
Wiley
,
Hoboken, NJ
.
You do not currently have access to this content.