The aim of this study is to investigate the influence of yield strength of the filler material and weld metal penetration on the load carrying capacity of butt welded joints in high-strength steels (HSS) (i.e., grade S700 and S960). These joints are manufactured with three different filler materials (under-matching, matching, and over-matching) and full and partial weld metal penetrations. The load carrying capacities of these mentioned joints are evaluated with experiments and compared with the estimations by finite element analysis (FEA), and design rules in Eurocode3 and American Welding Society Code AWS D1.1. The results show that load carrying estimations by FEA, Eurocode3, and AWS D1.1 are in good agreement with the experiments. It is observed that the global load carrying capacity and ductility of the joints are affected by weld metal penetration and yield strengths of the base and filler materials. This influence is more pronounced in joints in S960 steel welded with under-matched filler material. Furthermore, the base plate material strength can be utilized in under-matched butt welded joints provided appropriate weld metal penetration and width is assured. Moreover, it is also found that the design rules in Eurocode3 (valid for design of welded joints in steels of grade up to S700) can be extended to designing of welds in S960 steels by the use of correlation factor of one.

References

1.
CEN, 2004, “Eurocode 3: Design of Steel Structures—Part 1–8: Design of Joints,” European Committee for Standardization, Brussels.
2.
AWS Committee on Structural Welding, 2000, “AWS D1.1-Structural Welding Code–Steel,” American Welding Society, Miami, FL.
3.
CEN, 2005, “Eurocode 3-Part1-12-Additional Rules for Extension of the EN 1993-1-8 up to Grades S700,” European Committee for Standardization, Brussels.
4.
Björk
,
T.
,
Toivonen
,
J.
, and
Nykänen
,
T.
,
2012
, “
Capacity of Fillet Welded Joints Made of Ultra High-Strength Steel
,”
Weld. World.
,
56
(
3–4
), pp.
71
84
.10.1007/BF03321337
5.
Collin
,
P.
, and
Johansson
,
B.
,
2005
, “
Design of Welds in High Strength Steels
,”
4th European Conference on Steel and Composite Structures
, Maastricht, The Netherlands, June 8-10, Vol. C, pp.
4.10-89
4.10-98
.
6.
Rasche
,
C.
, and
Kuhlmann
,
U.
,
2009
, “
Investigations on Longitudinal Fillet Welded Lap Joints of HSS
,”
Nordic Steel Construction Conference
, (
NSCC2009
), Malmö, Sweden, Sept. 2-4, pp. 462–469.http://www.nordicsteel2009.se/pdf/20.pdf
7.
Khurshid
,
M.
,
Barsoum
,
Z.
, and
Mumtaz
,
N. A.
,
2012
, “
Ultimate Strength and Failure Modes for Fillet Welds in High Strength Steels
,”
Mater. Des.
,
40
, pp.
36
42
.10.1016/j.matdes.2012.03.048
8.
Picón
,
R.
, and
Cañas
,
J.
,
2009
, “
On Strength Criteria of Fillet Welds
,”
Int. J. Mech. Sci.
,
51
(
8
), pp.
609
618
.10.1016/j.ijmecsci.2009.06.003
9.
Mellor
,
B. G.
,
Rainey
,
R. C. T.
, and
Kirik
,
N. E.
,
1999
, “
The Static Strength of End and T Fillet Weld Connections
,”
Mater. Des.
,
20
(
4
), pp.
193
205
.10.1016/S0261-3069(99)00027-8
10.
Collin
,
P.
,
Möller
,
M.
,
Nilsson
,
M.
, and
Törnblom
,
S.
,
2009
, “
Undermatching Butt Welds in High Strength Steel
,”
International Association for Bridge and Structural Engineering Symposium
, Bangkok, Thailand, Sept. 9-11, pp. 96–106.10.2749/222137809796078829
11.
Gagnon
,
D. P.
, and
Laurie Kennedy
,
D. J.
,
1989
, “
Behaviour and Ultimate Tensile Strength of Partial Joint Penetration Groove Welds
,”
Can. J. Civil Eng.
,
16
(
3
), pp.
384
399
.10.1139/l89-062
12.
Lesik
,
D. F.
, and
Laurie Kennedy
,
D. J.
,
1990
, “
Ultimate Strength of Fillet Welded Connections Loaded in Plane
,”
Can. J. Civil Eng.
,
17
(
1
), pp.
55
67
.10.1139/l90-008
13.
Satoh
,
K.
, and
Toyoda
,
M.
,
1975
, “
Joint Strength of Heavy Plates With Lower Strength Weld Metal
,”
Welding Research Supplement
, pp.
311
319
.https://app.aws.org/wj/supplement/WJ_1975_09_s311.pdf
14.
Rodrigues
,
D. M.
,
Menezes
,
L. F.
,
Loureiro
,
A.
, and
Fernandes
,
J. V.
,
2004
, “
Numerical Study of the Plastic Behavior in Tension of Welds in High Strength Steels
,”
Int. J. Plast.
,
20
(
1
), pp.
1
18
.10.1016/S0749-6419(02)00112-2
15.
Loureiro
,
A. J. R.
,
2002
, “
Effect of Heat Input on Plastic Deformation of Undermatched Welds
,”
J. Mater. Process. Technol.
,
128
(
1–3
), pp.
240
249
.10.1016/S0924-0136(02)00457-0
16.
Mochizuki
,
M.
,
Shintomi
,
T.
,
Hashimoto
,
Y.
, and
Toyoda
,
M.
,
2004
, “
Analytical Study on Deformation and Strength in HAZ-Softened Welded Joints of Fine-Grained Steels
,”
Weld. World
,
48
(
9–10
), pp.
2
12
.10.1007/BF03263396
17.
Hochhauser
,
F.
,
Ernst
,
W.
,
Rauch
,
R.
,
Vallant
,
R.
, and
Enzinger
,
N.
,
2012
, “
Influence of the Soft Zone on the Strength of Welded Modern HSLA Steels
,”
Weld. World
,
56
(
5–6
), pp.
77
85
.10.1007/BF03321352
18.
Vuik
,
J.
,
van Wortel
,
J. C.
, and
van Sevenhoven
,
C.
,
1994
, “
Application of Very Low Strength Consumables in the Root Pass of Weldments to Avoid Preheating
,”
Weld. World
,
33
(
5
), pp.
362
369
.
19.
Panda
,
S. K.
,
Sreenivasan
,
N.
,
Kuntz
,
M. L.
, and
Zhou
,
Y.
,
2008
, “
Numerical Simulations and Experimental Results of Tensile Tests Behavior of Laser Butt Welded DP980 Steels
,”
ASME J. Eng. Mater. Technol.
,
130
(
4
), p.
041003
.10.1115/1.2969256
20.
SSAB
,
2009
,
Welding Handbook
, 1st ed., SSAB, Oxelösund AB, Stockholm, Sweden.
21.
SSI
,
2011
, “
Destructive Tests on Welds in Metallic Materials—Transverse Tensile Test
, Swedish Standards Institute, Stockholm, Sweden, Standard No. SS-EN ISO 4136.
22.
Swedish Standards Institute, 2011
, “
Destructive Tests on Welds in Metallic Material—Hardness Testing
,” Swedish Standards Institute, Stockholm, Sweden, Standard No. SS-EN ISO 9015-1.
23.
SSI, 2006
, “
Metallic Materials—Vickers Hardness Test
,” Swedish Standards Institute, Stockholm, Sweden, Standard No. SS-EN ISO 6507-1.
24.
Dexter
,
R. J.
,
1997
,
Significance of Strength Undermatching of Welds in Structural Behaviour
,
GKSS Research Center Publications
,
Geesthacht, Germany
, pp.
55
73
.
25.
Stoschka
,
M.
,
Leitner
,
M.
,
Posch
,
G.
, and
Eichlseder
,
W.
,
2013
, “
Effect of High-Strength Filler Metals on the Fatigue Behavior of Butt Joints
,”
Weld. World
,
57
(
1
), pp.
85
96
.10.1007/s40194-012-0010-6
26.
Hobbacher
,
A.
,
2007
, “
Recommendation for Fatigue Design of Welded Joints and Components
,” International Institute of Welding, Villepinte, France, IIW Document XIII-2151-07/XV-1254-07.
27.
Fricke
,
W.
,
2008
, “
Guideline for the Fatigue Assessment by Notch Stress Analysis for Welded Structures
,”
Hamburg University of Technology Ship Structural Design and Analysis
,
Hamburg, Germany
, IIW-Doc. XIII-2240r1-08/XV-1289r1-08.
28.
Cahhon
,
J. R.
,
1972
, “
An Improved Equation Relating Hardness to Ultimate Strength
,”
Metall. Trans.
,
3
(
11
), p.
3040
.10.1007/BF02652880
29.
Pavlina
,
E. J.
, and
Van Tyne
,
C. J.
,
2008
, “
Correlation of Yield Strength and Tensile Strength With Hardness for Steels
,”
J. Mater. Eng. Perform.
,
17
(
6
), pp.
888
893
.10.1007/s11665-008-9225-5
30.
Barsoum
,
I.
,
Khan
,
F.
, and
Barsoum
,
Z.
,
2014
, “
Analysis of the Torsional Strength of Hardened Splined Shafts
,”
Mater. Des.
,
54
, pp.
130
136
.10.1016/j.matdes.2013.08.020
31.
Koçak
,
M.
,
2010
, “
Structural Integrity of Welded Structures: Process–Property–Performance (3P) Relationship
,”
63rd Annual Assembly and International Conference of the International Institute of Welding
, Istanbul, Turkey, July 11-16, pp.
11
17
.
32.
Ananthan
,
V. S.
, and
Hall
,
E. O.
,
1991
, “
Macroscopic Aspects of Lüders Band Deformation in Mild Steel
,”
Acta Metall. Mater.
,
39
(
12
), pp.
3153
3160
.10.1016/0956-7151(91)90049-7
33.
Pisarski
,
H. G.
, and
Dolby
,
R. E.
,
2003
, “
The Significance of Softened HAZs in High Strength Structural Steels
,”
Weld. World
,
47
(
5–6
), pp.
32
40
.10.1007/BF03266387
34.
Maurer
,
W.
,
Ernst
,
W.
,
Rauch
,
R.
,
Kapl
,
S.
,
Pohl
,
A.
,
Krüssel
,
T.
,
Vallant
,
R.
, and
Enzinger
,
N.
,
2012
, “
Electron Beam Welding of a TMCP Steel With 700 MPa Yield Strength
,”
Weld. World
,
56
(
9–10
), pp.
85
94
.10.1007/BF03321384
You do not currently have access to this content.