Two types of defects normally occur in ultrasonically consolidated parts: (i) Defects that occur between mating foils in successive layers (“type 1” defects) and (ii) defects that occur within a layer between two foils laid side-by-side (“type 2” defects). While some success has been achieved in minimizing type 1 defects, type 2 defects, however, have been given very little attention. Both types of defects are undesirable and should be minimized if ultrasonically consolidated parts are to be used in structural applications. This work describes an investigation of how to minimize type 2 defects in ultrasonically consolidated parts. According to our hypothesis, a foil being deposited must overlap the adjacent deposited foil by an optimum amount to ensure a defect-free joint between the two foils. Transverse tensile specimens were fabricated with various amounts of foil overlap (by changing the foil width setting) to test this hypothesis. Metallographic and fractographic studies showed a clear correlation between foil overlap, defect incidence, and tensile strength. It was found that a foil width setting of 23.81 mm helps minimize type 2 defects in ultrasonically consolidated Al 3003 parts using standard foils of 23.88 mm (equivalent to 0.94 in.) nominal width.
Skip Nav Destination
e-mail: brent.stucker@usu.edu
Article navigation
January 2010
Research Papers
Minimizing Defects Between Adjacent Foils in Ultrasonically Consolidated Parts
J. O. Obielodan,
J. O. Obielodan
Department of Mechanical and Aerospace Engineering,
Utah State University
, Logan, UT 84322-4130
Search for other works by this author on:
G. D. Janaki Ram,
G. D. Janaki Ram
Department of Mechanical and Aerospace Engineering,
Utah State University
, Logan, UT 84322-4130
Search for other works by this author on:
B. E. Stucker,
B. E. Stucker
Department of Mechanical and Aerospace Engineering,
e-mail: brent.stucker@usu.edu
Utah State University
, Logan, UT 84322-4130
Search for other works by this author on:
D. G. Taggart
D. G. Taggart
Department of Mechanical Engineering,
University of Rhode Island
, Kingston, RI 02881
Search for other works by this author on:
J. O. Obielodan
Department of Mechanical and Aerospace Engineering,
Utah State University
, Logan, UT 84322-4130
G. D. Janaki Ram
Department of Mechanical and Aerospace Engineering,
Utah State University
, Logan, UT 84322-4130
B. E. Stucker
Department of Mechanical and Aerospace Engineering,
Utah State University
, Logan, UT 84322-4130e-mail: brent.stucker@usu.edu
D. G. Taggart
Department of Mechanical Engineering,
University of Rhode Island
, Kingston, RI 02881J. Eng. Mater. Technol. Jan 2010, 132(1): 011006 (8 pages)
Published Online: November 3, 2009
Article history
Received:
December 1, 2008
Revised:
April 20, 2009
Online:
November 3, 2009
Published:
November 3, 2009
Citation
Obielodan, J. O., Ram, G. D. J., Stucker, B. E., and Taggart, D. G. (November 3, 2009). "Minimizing Defects Between Adjacent Foils in Ultrasonically Consolidated Parts." ASME. J. Eng. Mater. Technol. January 2010; 132(1): 011006. https://doi.org/10.1115/1.3184033
Download citation file:
Get Email Alerts
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Microstructural Characterization of Ultrasonically Welded Aluminum
J. Eng. Mater. Technol (January,2005)
Evaluation of Additive Friction Stir Deposition for the Repair of Cast Al-1.4Si-1.1Cu-1.5Mg-2.1Zn
J. Manuf. Sci. Eng (June,2022)
Statistical Characterization of Ultrasonic Additive Manufacturing Ti/Al Composites
J. Eng. Mater. Technol (October,2010)
Optimizing Ultrasonic Additive Manufactured Al 3003 Properties With Statistical Modeling
J. Eng. Mater. Technol (January,2012)
Related Proceedings Papers
Related Chapters
Concluding Remarks and Future Work
Ultrasonic Welding of Lithium-Ion Batteries
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Introduction
Ultrasonic Welding of Lithium-Ion Batteries