Polymer-based composite materials are used in a variety of industry. Recently, thermoplastic polymer suitable for the resinous matrix in carbon fiber-reinforced composites has been introduced for lower material and processing costs, improved damage tolerance and higher moisture resistance. The successful use of this material requires sophisticated production technology, however little reference of machining of thermoplastics composites can be found. The existing published results are almost exclusively for epoxy-based composite materials showing difficulty in avoiding poor finish, serious tool wear and delamination at hole entrance and exit due to the brittle material response to machining. Thermoplastics-based composite materials possesses better machinability. The current work reveals the machinability of an example of carbon fiber-reinforced ABS (Acrylonitrile Butadiene Styrene) in drilling compared to representative metals and thermoset-based composites. The observation of chips reveals that considerable plastic deformation is involved. Compared to the chip formation of thermoset plastics, it contributes to the improved edge quality in drilling. The edge quality is generally fine except in the case of concentrated heat accumulation at tool lips, which is generated by high cutting speed and low feed rate. Plastics tend to be extruded out of the edge rather than neatly cut. The average surface roughness along hole walls in commonly below one micron for all sets of cutting conditions in the experiment, values between 0.3 and 0.6 microns are typical. The high speed steel drill presents only minor tool wear during the tests. Based on these results, one concludes that the carbon fiber-reinforced ABS demonstrates good machinability in drilling.
Skip Nav Destination
Article navigation
January 1993
Research Papers
Machinability of Fiber-Reinforced Thermoplastics in Drilling
H. Hocheng,
H. Hocheng
Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu, Taiwan
Search for other works by this author on:
H. Y. Puw
H. Y. Puw
Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu, Taiwan
Search for other works by this author on:
H. Hocheng
Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu, Taiwan
H. Y. Puw
Department of Power Mechanical Engineering, National Tsing Hua University, Hsinchu, Taiwan
J. Eng. Mater. Technol. Jan 1993, 115(1): 146-149 (4 pages)
Published Online: January 1, 1993
Article history
Received:
June 1, 1991
Revised:
June 17, 1992
Online:
April 29, 2008
Citation
Hocheng, H., and Puw, H. Y. (January 1, 1993). "Machinability of Fiber-Reinforced Thermoplastics in Drilling." ASME. J. Eng. Mater. Technol. January 1993; 115(1): 146–149. https://doi.org/10.1115/1.2902148
Download citation file:
Get Email Alerts
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Drilling of Aramid and Carbon Fiber Polymer Composites
J. Manuf. Sci. Eng (November,2002)
Machinability of AISI 316 Austenitic Stainless Steel With Cryogenically Treated M35 High-Speed Steel Twist Drills
J. Manuf. Sci. Eng (December,2012)
Experimental Investigations into Traveling Wire Electrochemical Spark Machining (TW-ECSM) of Composites
J. Eng. Ind (February,1991)
Chisel Edge and Pilot Hole Effects in Drilling Composite Laminates
J. Manuf. Sci. Eng (May,2002)
Related Proceedings Papers
Related Chapters
Study on Screw Drill Wear When Drilling Low Carbon Stainless Steel and Accompanying Phenomena in the Cutting Zone
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)
Novel and Efficient Mathematical and Computational Methods for the Analysis and Architecting of Ultralight Cellular Materials and their Macrostructural Responses
Advances in Computers and Information in Engineering Research, Volume 2
Introductory Survey
Introduction to Plastics Engineering