Abstract
The rapid evolution of electronic and information technology has increased the performance of the electronic processors significantly. Achieving the optimal performance in a smart electronic device poses a serious challenge as the heat generated during operation will reduce the performance of the device which makes thermal management a determinant factor. Powder injection molding (PIM) is an appropriate and relatively new technology used for mass production of small delicate parts with complex shapes and desired properties. One of the latest advances in the PIM process is the production of metal matrix nanocomposites with huge industrial applications, particularly in electronics manufacturing. Manufacturing of efficient complex-shaped nanocomposites, as thermal management components (passive heatsink), could be achieved through the PIM process. On the other hand, what could pose a challenge is the presence of nanoparticles affecting on the different stages of PIM process including feedstock preparation, molding, debinding, and sintering. In this paper, the effect of nanoparticles on different stages of PIM for the production of heatsinks is investigated. Then, the manufacturing of Cu-, Al-, and Mg-based nanocomposites by powder injection molding, as heatsinks, is reviewed followed by investigating the related advantages and limitations.
References
1.
Rajabi
, J.
, Muhamad
, N.
, and Sulong
, A. B.
, 2012
, “Effect of Nano-sized Powders on Powder Injection Molding: A Review
,” Microsyst. Technol.
, 18
(12
), pp. 1941
–1946
. 10.1007/s00542-012-1631-92.
Weber
, D. N.
, Shaw
, C. F.
, and Petering
, D. H.
, 1987
, “Euglena Gracilis Cadmium-Binding Protein-II Contains Sulfide Ion
,” J. Biol. Chem.
, 262
(15
), pp. 6962
–6964
.3.
Alshammari
, B. A.
, Saba
, N.
, Alotaibi
, M. D.
, Alotibi
, M. F.
, Jawaid
, M.
, and Alothman
, O. Y.
, 2019
, “Evaluation of Mechanical, Physical, and Morphological Properties of Epoxy Composites Reinforced With Different Date Palm Fillers
,” Materials
, 12
(13
), p. 2145
. 10.3390/ma121321454.
Hancox
, N. L.
, 1996
, “Engineering Mechanics of Composite Materials
,” Mater. Des.
, 2
(17
), p. 114
. 10.1016/S0261-3069(97)87195-65.
Kumar
, A.
, Lal
, S.
, and Kumar
, S.
, 2013
, “Fabrication and Characterization of A359/Al2O3 Metal Matrix Composite Using Electromagnetic Stir Casting Method
,” J. Mater. Res. Technol.
, 2
(3
), pp. 250
–254
. 10.1016/j.jmrt.2013.03.0156.
Rosso
, M.
, 2006
, “Ceramic and Metal Matrix Composites: Routes and Properties
,” J. Mater. Process. Technol.
, 175
(1–3
), pp. 364
–375
. 10.1016/j.jmatprotec.2005.04.0387.
Casati
, R.
, and Vedani
, M.
, 2014
, “Metal Matrix Composites Reinforced by Nano-particles—A Review
,” Metals
, 4
(1
), pp. 65
–83
. 10.3390/met40100658.
Rozhbiany
, F. A. R.
, and Jalal
, S. R.
, 2019
, “Influence of Reinforcement and Processing on Aluminum Matrix Composites Modified by Stir Casting Route
,” Adv. Compos. Lett.
, 28
(1
), pp. 1
–8
.9.
Rozhbiany
, F. A. R.
, and Jalal
, S. R.
, 2020
, “The Effectiveness of Reinforcement and Processing on Mechanical Properties, Wear Behavior and Damping Response of Aluminum Matrix Composites
,” High Temp. Mater. Process
, 38
(2019
), pp. 927
–939
. 10.1515/htmp-2019-003910.
Jawaid
, M.
, Thariq
, M.
, and Saba
, N.
, 2018
, Failure Analysis in Biocomposites, Fibre-Reinforced Composites and Hybrid Composites
, Woodhead Publishing
, Cambridge
.11.
Camargo
, P. H. C.
, Satyanarayana
, K. G.
, and Wypych
, F.
, 2009
, “Nanocomposites: Synthesis, Structure, Properties and New Application Opportunities
,” Mater. Res.
, 12
(1
), pp. 1
–39
. 10.1590/S1516-1439200900010000212.
Rathod
, V. T.
, Kumar
, J. S.
, and Jain
, A.
, 2017
, “Polymer and Ceramic Nanocomposites for Aerospace Applications
,” Appl. Nanosci.
, 7
(8
), pp. 519
–548
. 10.1007/s13204-017-0592-913.
Imbaby
, M. F.
, and Jiang
, K.
, 2009
, “Fabrication of Free Standing 316-L Stainless Steel-Al2O3 Composite Micro Machine Parts by Soft Moulding
,” Acta Mater.
, 57
(16
), pp. 4751
–4757
. 10.1016/j.actamat.2009.06.03414.
Mazloum
, A.
, Kováčik
, J.
, Emmer
, Š
, and Sevostianov
, I.
, 2016
, “Copper–Graphite Composites: Thermal Expansion, Thermal and Electrical Conductivities, and Cross-Property Connections
,” J. Mater. Sci.
, 51
(17
), pp. 7977
–7990
. 10.1007/s10853-016-0067-515.
Yemisci
, I.
, Mutlu
, O.
, Gulsoy
, N.
, Kunal
, K.
, Atre
, S.
, and Gulsoy
, H. O.
, 2019
, “Experimentation and Analysis of Powder Injection Molded Ti10Nb10Zr Alloy: A Promising Candidate for Electrochemical and Biomedical Application
,” J. Mater. Res. Technol.
, 8
(6
), pp. 5233
–5245
. 10.1016/j.jmrt.2019.08.04616.
Oh
, J. W.
, Gal
, C. W.
, Shin
, D.
, Park
, J. M.
, Yang
, W. S.
, and Park
, S. J.
, 2018
, “Powder Injection Molding Process in Industrial Fields
,” J. Japan Soc. Powder Powder Metallurgy
, 65
(9
), pp. 539
–547
. 10.2497/jjspm.65.53917.
Qin
, M.
, Lu
, H.
, Wu
, H.
, He
, Q.
, Liu
, C.
, Mu
, X.
, Wang
, Y.
, Jia
, B.
, and Qu
, X.
, 2019
, “Powder Injection Molding of Complex-Shaped Aluminium Nitride Ceramic With High Thermal Conductivity
,” J. Eur. Ceram. Soc.
, 39
(4
), pp. 952
–956
. 10.1016/j.jeurceramsoc.2018.11.03718.
Verzola
, R.
, 2006
, “Technology Issues and the New ICTs
,” LEONARDO
, 39
(4
), pp. 311
–313
. 10.1162/leon.2006.39.4.31119.
Biron
, M.
, 2012
, Thermoplastics and Thermoplastic Composites
, William Andrew
, Norwich
.20.
Johnson
, J. L.
, 2019
, Handbook of Metal Injection Molding
, Woodhead Publishing
, Cambridge
, pp. 461
–498
.21.
Raza
, M. R.
, Ahmad
, F.
, Muhamad
, N.
, Sulong
, A. B.
, Omar
, M. A.
, Akhtar
, M. N.
, Nazir
, M. S.
, Muhsan
, A. S.
, and Aslam
, M.
, 2014
, “Effects of Residual Carbon on Microstructure and Surface Roughness of PIM 316L Stainless Steel
,” International Civil and Infrastructure Engineering Conference (InCIEC 2014)
, Sabah, Malaysia
, September
, pp. 927
–935
.22.
Cho
, H.
, Park
, J. M.
, Rho
, J.
, and Park
, S. J.
, 2019
, “Warpage of Powder Injection Molded Copper Structure
,” Metals Mater. Int.
, pp. 1
–7
.23.
Rabilah
, R.
, Wahab
, N. A.
, Omar
, M. A.
, Jaafar
, T. R.
, Budin
, S.
, Hashim
, S. M.
, Sauti
, R.
, and Razak
, M. A.
, 2017
, “Physical and Mechanical Properties of Injection Moulded 316L Stainless Steel Using Waste Rubber Binder
,” AIP Conference Proceedings
, 1901
(1
), p. 130022
. 10.1063/1.501058224.
Lu
, H.
, Qin
, M.
, Wu
, H.
, He
, Q.
, Liu
, C.
, Mu
, X.
, Wang
, Y.
, Jia
, B.
, and Qu
, X.
, 2019
, “Effect of AlN Powders on the Debinding and Sintering Behavior, and Thermal Conductivity of Injection Molded AlN Ceramics
,” Ceram. Int.
, 45
(18
), pp. 23890
–23894
. 10.1016/j.ceramint.2019.08.18325.
Ni
, J.
, Yu
, M.
, and Han
, K.
, 2018
, “Debinding and Sintering of an Injection-Moulded Hypereutectic Al–Si Alloy
,” Materials
, 11
(5
), p. 807
. 10.3390/ma1105080726.
Zhao
, M.
, Qiao
, L.
, Zheng
, J.
, Ying
, Y.
, Yu
, J.
, Li
, W.
, and Che
, S.
, 2019
, “Investigation of the Solvent Debinding in the Injection Molding of ZrO2 Ceramics Using LDEP, HDPE and Wax Binders
,” Ceram. Int.
, 45
(3
), pp. 3894
–3901
. 10.1016/j.ceramint.2018.11.06227.
Kadiman
, N. N.
, Rashid
, M. O. A.
, Muhamad
, N.
, and Sulong
, A. B.
, 2018
, “Effects of Sintering Temperature on the Physical and Mechanical Properties of Injection-Molded Copper/Graphene Composite
,” J. Adv. Manuf. Technol.
, 12
(1
), pp. 49
–60
.28.
Romero
, A.
, and Herranz
, G.
, 2017
, “Development of Feedstocks Based on Steel Matrix Composites for Metal Injection Moulding
,” Powder Technol.
, 308
(2
), pp. 472
–478
. 10.1016/j.powtec.2016.12.05529.
Demers
, V.
, Turenne
, S.
, and Scalzo
, O.
, 2015
, “Segregation Measurement of Powder Injection Molding Feedstock Using Thermogravimetric Analysis, Pycnometer Density and Differential Scanning Calorimetry Techniques
,” Adv. Powder Technol.
, 26
(3
), pp. 997
–1004
. 10.1016/j.apt.2015.04.00530.
Wang
, Y.
, Qu
, X.
, Zhang
, W.
, and Li
, Y.
, 2011
, “Analysis of Powder Segregation in Powder Injection Molding
,” Adv. Mater. Res
, 217
(3
), pp. 1372
–1379
. www.scientific.net/AMR.217-218.137231.
Demers
, V.
, Fareh
, F.
, Turenne
, S.
, Demarquette
, N. R.
, and Scalzo
, O.
, 2018
, “Experimental Study on Moldability and Segregation of Inconel 718 Feedstocks Used in Low-Pressure Powder Injection Molding
,” Adv. Powder Technol.
, 29
(1
), pp. 180
–190
. 10.1016/j.apt.2017.10.02532.
Enneti
, R. K.
, Onbattuvelli
, V. P.
, Gulsoy
, O.
, Kate
, K. H.
, and Atre
, S. V.
, 2019
, Handbook of Metal Injection Molding
, Woodhead Publishing
, Cambridge
, pp. 57
–88
.33.
Banerjee
, S.
, and Joens
, C. J.
, 2019
, Handbook of Metal Injection Molding
, Woodhead Publishing
, Cambridge
, pp. 129
–171
.34.
Askari
, A.
, Alaei
, M. H.
, Omrani
, A. M.
, Nekouee
, K.
, and Park
, S. J.
, 2019
, “Rheological and Thermal Characterization of AISI 4605 low-Alloy Steel Feedstock for Metal Injection Molding Process
,” Metals Mater. Int.
, pp. 1
–10
. 10.1007/s12540-019-00442-935.
Wen
, J.
, Liu
, W.
, Xie
, Z.
, Lou
, C.
, and Yang
, X.
, 2018
, “Effects of the Binder Compositions on the Homogeneity of Ceramic Injection Molded Compacts
,” Ceram. Int.
, 44
(3
), pp. 3218
–3225
. 10.1016/j.ceramint.2017.11.09336.
Lin
, D.
, Sanetrnik
, D.
, Cho
, H.
, Chung
, S. T.
, Kwon
, Y. S.
, Kate
, K. H.
, Hausnerova
, B.
, Atre
, S. V.
, and Park
, S. J.
, 2017
, “Rheological and Thermal Debinding Properties of Blended Elemental Ti-6Al-4V Powder Injection Molding Feedstock
,” Powder Technol.
, 311
(4
), pp. 357
–363
. 10.1016/j.powtec.2016.12.07137.
Fareh
, F.
, Demers
, V.
, Turenne
, S.
, and Scalzo
, O.
, 2016
, “Segregation Measurement of Inconel 718 Feedstocks Used in Low-Pressure Metal Injection Molding
,” Mater. Sci. Forum
, 857
, pp. 286
–290
. 10.4028/www.scientific.net/MSF.857.28638.
Chainer
, T. J.
, Schultz
, M. D.
, Parida
, P. R.
, and Gaynes
, M. A.
, 2017
, “Improving Data Center Energy Efficiency With Advanced Thermal Management
,” IEEE Transactions Components, Packaging Manuf. Technol.
, 7
(8
), pp. 1228
–1239
. 10.1109/TCPMT.2017.266170039.
Abbasi
, A.
, Firouzi
, B.
, and Sendur
, P.
, 2019
, “On the Application of Harris Hawks Optimization (HHO) Algorithm to the Design of Microchannel Heat Sinks
,” Eng. Comput.
, pp. 1
–20
. 10.1007/s00366-019-00892-040.
Muhsan
, A. S.
, and Ahmad
, F.
, 2011
, “Development of Nanocomposites Heat Sink (MWCNTs/Cu) Using Powder Injection Moulding for Electronic Applications
,” National Postgraduate Conference
, Kuala Lumpur, Malaysia
, Sept. 19–20
, pp. 1
–6
.41.
McGlen
, R. J.
, Jachuck
, R.
, and Lin
, S.
, 2004
, “Integrated Thermal Management Techniques for High Power Electronic Devices
,” Appl. Therm. Eng.
, 24
(8-9
), pp. 1143
–1156
. 10.1016/j.applthermaleng.2003.12.02942.
Ahmed
, H. E.
, Salman
, B. H.
, Kherbeet
, A. S.
, and Ahmed
, M. I.
, 2018
, “Optimization of Thermal Design of Heat Sinks : A Review
,” Int. J. Heat Mass Transf.
, 118
(3
), pp. 129
–153
. 10.1016/j.ijheatmasstransfer.2017.10.09943.
Kumar
, A.
, Kumar
, R.
, and Behura
, A. K.
, 2017
, “A Review of Electro Thermal Cooling Systems With Heat Sink
,” Int. J. Eng. Res. Manag. (IJERM)
, 4
(8
), pp. 19
–23
.44.
Shang
, B.
, Ma
, Y.
, Hu
, R.
, Yuan
, C.
, Hu
, J.
, and Luo
, X.
, 2017
, “Passive Thermal Management System for Downhole Electronics in Harsh Thermal Environments
,” Appl. Therm. Eng.
, 118
(5
), pp. 593
–599
. 10.1016/j.applthermaleng.2017.01.11845.
Wu
, Y.
, Lai
, L.
, Wang
, Y.
, Yang
, Z.
, Wang
, H.
, and Ding
, G.
, 2019
, “Micro Heat Sink Structure With High Thermal Conductive Composite via Micromachining Process
,” Proceedings of 20th International Conference on Solid-State Sensors, Actuators and Microsystems & Eurosensors XXXIII (Transducers & Eurosensors XXXIII)
, Berlin, Germany
, June 23–27
, pp. 1776
–1779
.46.
Mjallal
, I.
, Farhat
, H.
, Hammoud
, M.
, Ali
, S.
, Shaer
, A. A.
, and Assi
, A.
, 2018
, “Cooling Performance of Heat Sinks Used in Electronic Devices
,” The First International Conference on Energy, Power, Petroleum and Petrochemical Engineering (E3PE 2017)
, Beirut, Lebanon
, April 2017
, Vol. 171
, p. 02003
.47.
Ryu
, B. D.
, Han
, M.
, Ko
, K. B.
, Lee
, K. H.
, Cuong
, T. V.
, Han
, N.
, Kim
, K.
, Ryu
, J. H.
, Park
, N. J.
, Lim
, Y.
, and Jo
, C. H.
, 2019
, “Reduced Thermal Resistance of Heat Sink Using Graphene Oxide Decorated With Copper Nanoparticles
,” Mater. Res. Bull.
, 110
(2
), pp. 76
–81
. 10.1016/j.materresbull.2018.06.02848.
Johnson
, J. L.
, Tan
, L. K.
, Bollina
, R.
, Suri
, P.
, and German
, R. M.
, 2005
, “Evaluation of Copper Powders for Processing Heat Sinks by Metal Injection Moulding
,” Powder Metall.
, 48
(2
), pp. 123
–128
. 10.1179/003258905X3779249.
Mohammadi
, F.
, and Li
, S. S.
, 2018
, “Copper Like Thermal Conductivity and Silicon Like Coefficient of Thermal Expansion Copper Graphene for High Power IGBT by Metal Injection Molding
,” Mater. Trans.
, 59
(11
), pp. 1677
–1683
. 10.2320/matertrans.M201813650.
Mohammadi
, F.
, Arab
, N.
, and Li
, S. S.
, 2018
, “Metal Injected Copper Carbon Nanotube Composite Material With High Thermal Conductivity and Low CTE for IGBT Power Modules
,” Mater. Trans.
, 59
(8
), pp. 1251
–1258
. 10.2320/matertrans.M201800651.
Muhsan
, A. S.
, Ahmad
, F.
, Mohamed
, N. M.
, Yusoff
, P. S. M. M. B.
, and Raza
, M. R.
, 2014
, “Effect of CNTs Dispersion on the Thermal and Mechanical Properties of Cu/CNTs Nanocomposites
,” AIP Conference Proceedings, American Institute of Physics
, 1621
(1
), pp. 643
–649
. 10.1063/1.489853652.
Muhsan
, A. S.
, Ahmad
, F.
, Mohamed
, N. M.
, and Raza
, M. R.
, 2011
, “Flow Behavior of Cu/CNTs Feedstocks for Powder Injection Molding
,” Int. J. Appl. Phys. Math.
, 1
(3
), pp. 199
–202
. 10.7763/IJAPM.2011.V1.3953.
Naseer
, A.
, Ahmad
, F.
, Muhsan
, A. S.
, and Aslam
, M.
, 2019
, “Investigation of Suitable Graphene Reinforcements for Copper Based PIM Feedstock
,” Mater. Today Proc.
, 16
(Part 4
), pp. 2052
–2059
. 10.1016/j.matpr.2019.06.09154.
Abdoos
, H.
, Khorsand
, H.
, and Yousefi
, A. A.
, 2017
, “Nano-particles in Powder Injection Molding of an Aluminum Matrix Composite: Rheological Behavior, Production and Properties
,” Int. J. Mater. Res.
, 108
(3
), pp. 237
–244
. 10.3139/146.11146855.
Abdoos
, H.
, Khorsand
, H.
, and Yousefi
, A. A.
, 2016
, “On the Study of Mechanical Properties of Aluminum / Nano- Alumina Composites Produced via Powder Injection Molding
,” Mech. Adv. Compos. Struct.
, 3
(1
), pp. 45
–51
.56.
Rodríguez-Arbaizar
, M.
, Hamdan
, H.
, Leparoux
, M.
, Kollo
, L.
, Kwon
, H.
, and Carreño-Morelli
, E.
, 2010
, “Net-Shape Al6061/SiC Nanocomposites by Powder Injection Moulding
,” PM2010 WorldCongress
, Florence, Italy
, Oct. 10–14
.57.
Ghanbari
, A.
, Alizadeh
, M.
, Ghasemi
, E.
, Rad
, R. Y.
, and Ghaffari
, S.
, 2015
, “Preparation of Optimal Feedstock for Low-Pressure Injection Molding of Al/SiC Nanocomposite
,” Sci. Eng. Compos. Mater
, 22
(5
), pp. 549
–554
. 10.1515/secm-2013-020958.
Dhore
, V. G.
, Rathod
, W. S.
, and Patil
, K. N.
, 2018
, “Investigation of Mechanical Properties of Carbon Nanotubes Reinforced Aluminium Composite by Metal Injection Molding
,” Mater. Today Proc.
, 5
(9
), pp. 20690
–20698
. 10.1016/j.matpr.2018.06.45259.
Taheri
, S. M.
, Ghasemi
, E.
, Alizadeh
, M.
, and Rad
, R. Y.
, 2014
, “Rheological Properties of Mg Based Feedstocks With Micro or Nano Al2O3 Powder for Injection Molding
,” J. Ceram. Process. Res.
, 15
(4
), pp. 236
–241
.60.
Kim
, K. H.
, Youn
, H. C.
, Choi
, C. J.
, and Lee
, B. T.
, 2007
, “Fabrication and Material Properties of Powder Injection Molded Fe Sintered Bodies Using Nano Fe Powder
,” Mater. Lett.
, 61
(4-5
), pp. 1218
–1222
. 10.1016/j.matlet.2006.07.00261.
Yu
, P. C.
, Li
, Q. F.
, Fuh
, J. Y. H.
, Li
, T.
, and Ho
, P. W.
, 2009
, “Micro Injection Molding of Micro Gear Using Nano-sized Zirconia Powder
,” Microsyst. Technol.
, 15
(3
), pp. 401
–406
. 10.1007/s00542-008-0673-562.
Son
, S. J.
, Cho
, Y. S.
, and Choi
, C. J.
, 2011
, “Advanced Micromanufacturing for High-Precision Micro Bearing by Nanopowder Metallurgy and LIGA Processing
,” Rev. Adv. Mater. Sci.
, 28
(7
), pp. 190
–195
.63.
Hassan
, S. F.
, and Gupta
, M.
, 2006
, “Effect of Particulate Size of Al2O3 Reinforcement on Microstructure and Mechanical Behavior of Solidification Processed Elemental Mg
,” J. Alloys Compd.
, 419
(1-2
), pp. 84
–90
. 10.1016/j.jallcom.2005.10.00564.
Kim
, K. H.
, Lee
, B. T.
, and Choi
, C. J.
, 2010
, “Fabrication and Evaluation of Powder Injection Molded Fe-Ni Sintered Bodies Using Nano Fe-50%Ni Powder
,” J. Alloys Compd.
, 491
(1–2
), pp. 391
–394
. 10.1016/j.jallcom.2009.10.19265.
Oh
, J. W.
, Bollina
, R.
, Lee
, W. S.
, and Park
, S. J.
, 2016
, “Effect of Nanopowder Ratio in Bimodal Powder Mixture on Powder Injection Molding
,” Powder Technol.
, 302
(11
), pp. 168
–176
. 10.1016/j.powtec.2016.08.05166.
Choi
, J.
, Park
, J.
, Song
, J.
, Lee
, W.
, and Lee
, J.
, 2017
, “Design of Trimodal Fe Micro-Nanopowder Feedstock for Micro Powder Injection Molding
,” Powder Technol.
, 317
(7
), pp. 1
–5
. 10.1016/j.powtec.2017.04.05167.
Onbattuvelli
, V. P.
, Enneti
, R. K.
, Park
, S. J.
, and Atre
, S. V.
, 2013
, “The Effects of Nanoparticle Addition on SiC and AlN Powder-Polymer Mixtures: Packing and Flow Behavior
,” Int. J. Refractory Metals Hard Mater.
, 36
(1
), pp. 183
–190
. 10.1016/j.ijrmhm.2012.08.01468.
Kim
, Y.
, Lee
, S.
, Noh
, J. W.
, Lee
, S. H.
, Jeong
, I. D.
, and Park
, S. J.
, 2013
, “Rheological and Sintering Behaviors of Nanostructured Molybdenum Powder
,” Int. J. Refractory Metals Hard Mater.
, 41
(11
), pp. 442
–448
. 10.1016/j.ijrmhm.2013.06.00169.
Olhero
, S. M.
, and Ferreira
, J. M. F.
, 2004
, “Influence of Particle Size Distribution on Rheology and Particle Packing of Silica-Based Suspensions
,” Powder Technol.
, 139
(1
), pp. 69
–75
. 10.1016/j.powtec.2003.10.00470.
Attia
, U. M.
, and Alcock
, J. R.
, 2011
, “A Review of Micro-powder Injection Moulding as a Microfabrication Technique
,” J. Micromech. Microeng.
, 21
(4
), p. 043001
. 10.1088/0960-1317/21/4/04300171.
Han
, J. S.
, Gal
, C. W.
, Park
, J. M.
, and Park
, S. J.
, 2017
, “Powder Injection Molding of PNN-PMN-PZN Doped Low Temperature Sintering PZT Ceramics
,” J. Manuf. Process
, 28
(Part 1
), pp. 235
–242
. 10.1016/j.jmapro.2017.06.00872.
Rajabi
, J.
, Muhamad
, N.
, Sulong
, A. B.
, Fayyaz
, A.
, and Wahi
, A.
, 2012
, “Advantages and Limitations of Using Nano Sized Powders for Powder Injection Molding Process: A Review
,” J. Teknol. Sci. Eng.
, 59
(2
), pp. 137
–140
.73.
Hansen
, M.
, and Anderko
, K.
, 1958
, Metallurgy and Metallurgical Engineering Series
, Mc Graw-Hil Book Company
, New York
.74.
Qian
, C.
, Gheitaghy
, A. M.
, Fan
, J.
, Tang
, H.
, Sun
, B.
, Ye
, H.
, and Zhang
, G.
, 2018
, “Thermal Management on IGBT Power Electronic Devices and Modules
,” IEEE Access
, 6
(3
), pp. 12868
–12884
. 10.1109/ACCESS.2018.279330075.
Chainer
, T. J.
, Member
, S.
, Schultz
, M. D.
, Parida
, P. R.
, and Michael
, A.
, 2017
, “Improving Data Center Energy Efficiency With Advanced Thermal Management
,” IEEE Transactions Components, Packaging Manuf. Technol.
, 7
(8
), pp. 1228
–1239
. 10.1109/TCPMT.2017.266170076.
Xu
, T.
, Li
, Y.
, Chen
, J.
, Wu
, H.
, Zhou
, X.
, and Zhang
, Z.
, 2018
, “Improving Thermal Management of Electronic Apparatus With Paraffin (PA)/Expanded Graphite (EG)/Graphene (GN) Composite Material
,” Appl. Therm. Eng.
, 140
(7
), pp. 13
–22
. 10.1016/j.applthermaleng.2018.05.06077.
Sevinchan
, E.
, Dincer
, I.
, and Lang
, H.
, 2018
, “A Review on Thermal Management Methods for Robots
,” Appl. Therm. Eng.
, 140
(7
), pp. 799
–813
. 10.1016/j.applthermaleng.2018.04.13278.
Sørensen
, N. J.
, Suresh
, S.
, Tvergaard
, V.
, and Needleman
, A.
, 1995
, “Effects of Reinforcement Orientation on the Tensile Response of Metal-Matrix Composites
,” Mater. Sci. Eng. A
, 197
(1
), pp. 1
–10
. 10.1016/0921-5093(94)09739-979.
Li
, M.
, and Akoshima
, M.
, 2020
, “Appropriate Metallic Coating for Thermal Diffusivity Measurement of Nonopaque Materials With Laser Flash Method and Its Effect
,” Int. J. Heat Mass Transfer
, 148
(2
), p. 119017
. 10.1016/j.ijheatmasstransfer.2019.11901780.
Raether
, F.
, Baber
, J.
, and Friedrich
, H.
, 2019
, “Thermal Management of Heating Processes–Measuring Heat Transfer Properties
,” Refract. Worldforum
, 11
(2
), pp. 59
–65
.81.
Oddone
, V.
, Boerner
, B.
, and Reich
, S.
, 2017
, “Composites of Aluminum Alloy and Magnesium Alloy With Graphite Showing Low Thermal Expansion and High Specific Thermal Conductivity
,” Sci. Technol. Adv. Mater.
, 18
(1
), pp. 180
–186
. 10.1080/14686996.2017.128622282.
Shirazi
, I.
, Ahmad
, F.
, Raza
, M. R.
, Muhsan
, A. S.
, and Aslam
, M.
, 2015
, “Shear Controlled Alignment of Short Carbon Fibers in Copper Matrix Composite Green Samples Produced by Powder Injection Molding
,” AIP Conf. Proc.
, 1669
(1
), p. 020043
. 10.1063/1.491918183.
Tan
, L. K.
, and Ma
, J.
, 2004
, “Performance of Powder Injection Molding (PIM) Heat Sink
,” The Ninth Intersociety Conference on Thermal and Thermomechanical Phenomena In Electronic Systems (IEEE Cat. No. 04CH37543)
, Las Vegas, NV
, June 1–4
, Vol. 1
, pp. 451
–454
.84.
Shirazi
, M. I.
, Ahmad
, F.
, Raza
, M. R.
, Muhsan
, A. S.
, Omer
, M. A.
, and Aslam
, M.
, 2014
, “Orientation of Carbon Fibers in Copper Matrix Produced by Powder Injection Molding
,” The 4th International Conference on Production, Energy and Reliability (ICPER2014)
, Kuala Lumpur, Malaysia
, June 2014
, p. 04027
.85.
Ahmad
, F.
, 2005
, “Orientation of Short Fibers in Powder Injection Molded Aluminum Matrix Composites
,” J. Mater. Process. Technol.
, 169
(2
), pp. 263
–269
. 10.1016/j.jmatprotec.2005.03.03686.
Zhang
, T.
, Evans
, J. R. G.
, and Bevis
, M. J.
, 1996
, “The Control of Fibre Orientation in Ceramic and Metal Composites by Open-Ended Injection Moulding
,” Compos. Sci. Technol.
, 56
(8
), pp. 921
–928
. 10.1016/0266-3538(96)00055-387.
Waschitschek
, K.
, Kech
, A.
, and Christiansen
, J. D.
, 2002
, “Influence of Push–Pull Injection Moulding on Fibres and Matrix of Fibre Reinforced Polypropylene
,” Composites Part A: Applied Science and Manufacturing
, 33
(5
), pp. 735
–744
. 10.1016/S1359-835X(02)00007-688.
Muhsan
, A. S.
, Ahmad
, F.
, Mohamed
, N. M.
, Megat Yusoff
, P. S. M.
, and Rafi Raza
, M.
, 2013
, “Uniform Dispersion of Multiwalled Carbon Nanotubes in Copper Matrix Nanocomposites Using Metal Injection Molding Technique
,” Int. J. Manuf. Eng.
, 2013
(1
), pp. 1
–10
. 10.1155/2013/38614189.
Liang
, S.
, Tang
, Y.
, Zhang
, Y.
, and Zhong
, J.
, 2009
, “The Rheologyical Effect of Carbon Nanotubes on the Iron Based Metal Powder Injection Molding Feedstock
,” Adv. Mater. Res.
, 79
, pp. 469
–472
. 10.4028/www.scientific.net/AMR.79-82.46990.
Awang
, M.
, Emamian
, S. S.
, and Yusof
, F.
, 2020
, Advances in Material Sciences and Engineering
, Springer
, New York
.91.
Daoush
, W. M.
, Lim
, B. K.
, Mo
, C. B.
, Nam
, D. H.
, and Hong
, S. H.
, 2009
, “Electrical and Mechanical Properties of Carbon Nanotube Reinforced Copper Nanocomposites Fabricated by Electroless Deposition Process
,” Mater. Sci. Eng. A
, 513
(7
), pp. 247
–253
. 10.1016/j.msea.2009.01.07392.
Cha
, S. I.
, Kim
, K. T.
, Arshad
, S. N.
, Mo
, C. B.
, and Hong
, S. H.
, 2005
, “Extraordinary Strengthening Effect of Carbon Nanotubes in Metal-Matrix Nanocomposites Processed by Molecular-Level Mixing
,” Adv. Mater.
, 17
(11
), pp. 1377
–1381
. 10.1002/adma.20040193393.
Abdoos
, H.
, Khorsand
, H.
, and Yousefi
, A. A.
, 2014
, “Torque Rheometry and Rheological Analysis of Powder–Polymer Mixture for Aluminum Powder Injection Molding
,” Iran. Polym. J, English Ed.
, 23
(10
), pp. 745
–755
. 10.1007/s13726-014-0268-194.
Khakbiz
, M.
, Simchi
, A.
, and Bagheri
, R.
, 2005
, “Analysis of the Rheological Behavior and Stability of 316L Stainless Steel-TiC Powder Injection Molding Feedstock
,” Mater. Sci. Eng. A
, 407
(1-2
), pp. 105
–113
. 10.1016/j.msea.2005.06.05795.
Zhang
, X. N.
, Geng
, L.
, and Wang
, G. S.
, 2006
, “Fabrication of Al-Based Hybrid Composites Reinforced With SiC Whiskers and SiC Nanoparticles by Squeeze Casting
,” J. Mater. Process. Technol.
, 176
(1–3
), pp. 146
–151
. 10.1016/j.jmatprotec.2006.03.12596.
Zhao
, N.
, Nash
, P.
, and Yang
, X.
, 2005
, “The Effect of Mechanical Alloying on SiC Distribution and the Properties of 6061 Aluminum Composite
,” J. Mater. Process. Technol.
, 170
(3
), pp. 586
–592
. 10.1016/j.jmatprotec.2005.06.03797.
Rajkovic
, V.
, Bozic
, D.
, and Jovanovic
, M. T.
, 2008
, “Properties of Copper Matrix Reinforced With Nano- and Micro-Sized Al2O3 Particles
,” J. Alloys Compd.
, 459
(1–2
), pp. 177
–184
. 10.1016/j.jallcom.2007.04.30798.
Rahimian
, M.
, Parvin
, N.
, and Ehsani
, N.
, 2010
, “Investigation of Particle Size and Amount of Alumina on Microstructure and Mechanical Properties of Al Matrix Composite Made by Powder Metallurgy
,” Mater. Sci. Eng. A
, 527
(4-5
), pp. 1031
–1038
. 10.1016/j.msea.2009.09.03499.
Tong
, X. C.
, 2011
, Advanced Materials for Thermal Management of Electronic Packaging
, Springer Science & Business Media
, Berlin/Heidelberg
.100.
Haghshenas
, M.
, and Gupta
, M.
, 2020
, “Magnesium Nanocomposites Reinforced With Rare Earth Element Nanoparticles: Nanoindentation-Driven Response
,” Nanocomposites
, 6
(1
), pp. 22
–30
. 10.1080/20550324.2019.1705592101.
Xi
, Y. L.
, Chai
, D. L.
, Zhang
, W. X.
, and Zhou
, J. E.
, 2005
, “Ti-6Al-4V Particle Reinforced Magnesium Matrix Composite by Powder Metallurgy
,” Mater. Lett.
, 59
(14–15
), pp. 1831
–1835
. 10.1016/j.matlet.2005.01.075Copyright © 2020 by ASME
You do not currently have access to this content.
