The residual stress profile in dissimilar metal sheets joined by a self-piercing rivet is simulated and compared to experimental measurements. Simulation of joining aluminum alloy 6111-T4 and steel HSLA340 sheets by self-piercing riveting (SPR) is performed using a two-dimensional axisymmetric model with an internal state variable (ISV) plasticity material model. Strain rate and temperature dependent deformation of the base materials is described by the ISV material model and calibrated with experimental data. Using the LS-DYNA simulation package, an element erosion technique is adopted in an explicit analysis of the separation of the upper sheet with maximum shear strain failure criterion. An explicit analysis with dynamic relaxation technique was then used for springback and cooling down analysis following the riveting simulation. The residual stress profile of SPR experimental joint with same configuration is characterized using neutron diffraction, and good agreement was found between the simulation and residual stress measurements.

References

1.
Liu
,
X.
,
Lan
,
S.
, and
Ni
,
J.
,
2015
, “
Thermal Mechanical Modeling of the Plunge Stage During Friction-Stir Welding of Dissimilar Al 6061 to TRIP 780 Steel
,”
ASME J. Manuf. Sci. Eng.
,
137
(
5
), p.
051017
.
2.
Skovron
,
J. D.
,
Prasad
,
R. R.
,
Ulutan
,
D.
,
Mears
,
L.
,
Detwiler
,
D.
,
Paolini
,
D.
,
Baeumler
,
B.
, and
Claus
,
L.
,
2015
, “
Effect of Thermal Assistance on the Joint Quality of Al6063-T5A During Flow Drill Screwdriving
,”
ASME J. Manuf. Sci. Eng.
,
137
(
5
), p.
051019
.
3.
Min
,
J.
,
Li
,
J.
,
Carlson
,
B. E.
,
Li
,
Y.
,
Quinn
,
J. F.
,
Lin
,
J.
, and
Wang
,
W.
,
2015
, “
Friction Stir Blind Riveting for Joining Dissimilar Cast Mg AM60 and Al Alloy Sheets
,”
ASME J. Manuf. Sci. Eng.
,
137
(
5
), p.
051022
.
4.
Satoh
,
G.
,
Qiu
,
C.
,
Naveed
,
S.
, and
Yao
,
Y. L.
,
2015
, “
Strength and Phase Identification of Autogenous Laser Brazed Dissimilar Metal Microjoints
,”
ASME J. Manuf. Sci. Eng.
,
137
(
1
), p.
011012
.
5.
Porcaro
,
R.
,
Hanssen
,
A. G.
,
Langseth
,
M.
, and
Aalberg
,
A.
,
2006
, “
Self-Piercing Riveting Process: An Experimental and Numerical Investigation
,”
J. Mater. Process. Technol.
,
171
(
1
), pp.
10
20
.
6.
Cacko
,
R.
,
2008
, “
Review of Different Material Separation Criteria in Numerical Modeling of the Self-Piercing Riveting Process
,”
Arch. Civ. Mech. Eng.
,
8
(
2
), pp.
21
30
.
7.
Stuhmeyer
,
A.
,
2005
, “
Simulation of Self-Piercing Riveting Process
,”
5th European LS-DYNA Users' Conference
, Birmingham, UK.
8.
Krishnappa
,
U. S.
,
2008
, “
Numerical Investigation of Self-Piercing Riveted Dual Layer Joint
,”
Master's thesis
, Wichita State University, Wichita, KS.
9.
Hoang
,
N. H.
,
Porcaro
,
R.
,
Langseth
,
M.
, and
Hanssen
,
A. G.
,
2010
, “
Self-Piercing Riveting Connections Using Aluminium Rivets
,”
Int. J. Solids Struct.
,
47
(3–4), pp.
427
439
.
10.
Casalino
,
G.
,
Rotondo
,
A.
, and
Ludovico
,
A.
,
2008
, “
On the Numerical Modelling of the Multiphysics Self Piercing Riveting Process Based on the Finite Element Technique
,”
Adv. Eng. Software
,
39
(
9
), pp.
787
795
.
11.
Moraes
,
J. F. C.
,
Jordon
,
J. B.
, and
Bammann
,
D. J.
,
2014
, “
Finite Element Analysis of Self-Pierce Riveting in Magnesium Alloys Sheets
,”
ASME J. Eng. Mater. Technol.
,
137
(
2
), p.
021002
.
12.
Huang
,
L.
,
Lasecki
,
J. V.
,
Guo
,
H.
, and
Su
,
X.
,
2014
, “
Finite Element Modeling of Dissimilar Metal Self-Piercing Riveting Process
,”
SAE
Paper No. 2014-01-1982.
13.
Durandet
,
Y.
,
Deam
,
R.
,
Beer
,
A.
,
Song
,
W.
, and
Blacket
,
S.
,
2010
, “
Laser Assisted Self-Pierce Riveting of AZ31 Magnesium Alloy Strips
,”
Mater. Des.
,
31
(
1
), pp.
S13
S16
.
14.
Wang
,
J. W.
,
Liu
,
Z. X.
,
Shang
,
Y.
,
Liu
,
A. L.
,
Wang
,
M. X.
,
Sun
,
R. N.
, and
Wang
,
P.-C.
,
2011
, “
Self-Piercing Riveting of Wrought Magnesium AZ31 Sheets
,”
ASME J. Manuf. Sci. Eng.
,
133
(
3
), p.
031009
.
15.
Ma
,
Y.
,
Lou
,
M.
,
Yang
,
Z.
, and
Li
,
Y.
,
2015
, “
Effect of Rivet Hardness and Geometrical Features on Friction Self-Piercing Riveted Joint Quality
,”
ASME J. Manuf. Sci. Eng.
,
137
(
5
), p.
054501
.
16.
Zener
,
C.
, and
Hollomon
,
J. H.
,
1944
, “
Effect of Strain Rate Upon Plastic Flow of Steel
,”
J. Appl. Phys.
,
15
(
1
), p.
22
.
17.
Johnson
,
G. R.
, and
Holmquist
,
T. J.
,
1988
, “
Evaluation of Cylinder-Impact Test Data for Constitutive Model Constants
,”
J. Appl. Phys.
,
64
(
8
), p.
3901
.
18.
Sherburn
,
J. A.
,
Horstemeyer
,
M. F.
,
Bammann
,
D. J.
, and
Baumgardner
,
J. R.
,
2011
, “
Application of the Bammann Inelasticity Internal State Variable Constitutive Model to Geological Materials
,”
Geophys. J. Int.
,
184
(
3
), pp.
1023
1036
.
19.
Bammann
,
D. J.
,
Chiesa
,
M. L.
,
Horstemeyer
,
M. F.
, and
Weingarten
,
L. I.
,
1993
, “
Failure in Ductile Materials Using Finite Element Methods
,” Structural Crashworthiness and Failure: Proceedings of the Third International Symposium on Structural Crashworthiness, Liverpool, UK,
CRC Press
,
Boca Raton, FL
, pp.
1
46
.
20.
Bammann
,
D. J.
, and
Aifantis
,
E. C.
,
1989
, “
A Damage Model for Ductile Metals
,”
Nucl. Eng. Des.
,
116
(
3
), pp.
355
362
.
21.
Bammann
,
D. J.
,
1990
, “
Modeling Temperature and Strain Rate Dependent Large Deformations of Metals
,”
Appl. Mech. Rev.
,
43
(
5
), pp.
S312
S319
.
22.
Abdelal
,
G. F.
,
Georgiou
,
G.
,
Cooper
,
J.
,
Robotham
,
A.
,
Levers
,
A.
, and
Lunt
,
P.
,
2015
, “
Numerical and Experimental Investigation of Aircraft Panel Deformations During Riveting Process
,”
ASME J. Manuf. Sci. Eng.
,
137
(
1
), p.
011009
.
23.
Haque
,
R.
,
Beynon
,
J. H.
,
Durandet
,
Y.
,
Kirstein
,
O.
, and
Blacket
,
S.
,
2012
, “
Feasibility of Measuring Residual Stress Profile in Different Self-Pierce Riveted Joints
,”
Sci. Technol. Weld. Joining
,
17
(
1
), pp.
60
68
.
24.
Withers
,
P. J.
,
Turski
,
M.
,
Edwards
,
L.
,
Bouchard
,
P. J.
, and
Buttle
,
D. J.
,
2008
, “
Recent Advances in Residual Stress Measurement
,”
Int. J. Pressure Vessels Piping
,
85
(
3
), pp.
118
127
.
25.
Sediako
,
D.
,
Elia
,
F.
,
Lombardi
,
A.
,
Machin
,
A.
,
Ravindran
,
C. R.
,
Hubbard
,
C.
, and
Mackay
,
R.
,
2011
, “
Analysis of Residual Stress Profiles in the Cylinder Web Region of an As-Cast V6 Al Engine Block With Cast-In Fe Liners Using Neutron Diffraction
,”
SAE
Paper No. 2011-01-0036.
26.
Park
,
J.-S.
,
Lienert
,
U.
,
Dawson
,
P. R.
, and
Miller
,
M. P.
,
2013
, “
Quantifying Three-Dimensional Residual Stress Distributions Using Spatially-Resolved Diffraction Measurements and Finite Element Based Data Reduction
,”
Exp. Mech.
,
53
(
9
), pp.
1491
1507
.
27.
Florea
,
R. S.
,
Hubbard
,
C. R.
,
Solanki
,
K. N.
,
Bammann
,
D. J.
,
Whittington
,
W. R.
, and
Marin
,
E. B.
,
2012
, “
Quantifying Residual Stresses in Resistance Spot Welding of 6061-T6 Aluminum Alloy Sheets Via Neutron Diffraction Measurements
,”
J. Mater. Process. Technol.
,
212
(
11
), pp.
2358
2370
.
28.
Skorupa
,
A.
, and
Skorupa
,
M.
,
2012
,
Riveted Lap Joints in Aircraft Fuselage: Design, Analysis and Properties
, Vol. 189,
Springer
,
The Netherlands
.
29.
Ali
,
M. Y.
, and
Pan
,
J.
,
2015
, “
Residual Stresses Due to Rigid Cylinder Indentation and Rolling at a Very High Rolling Load
,”
ASME J. Manuf. Sci. Eng.
,
137
(
5
), p.
051005
.
30.
Jaison
,
J.
,
2010
, “
Self-Pierce Riveting for Perfect Joints
,”
Boellhoff Corp.
, Bielefeld, Germany.
31.
Matlock
,
D. K.
,
Bruce
,
D. M.
, and
Speer
,
J. G.
,
2004
, “
Assessment of the Strain-Rate Dependent Tensile Properties of Automotive Sheet Steel
,”
SAE
Technical Paper No. 2004-01-0507.
32.
Cocks
,
A. C. F.
, and
Ashby
,
M. F.
,
1981
, “
On Creep Fracture by Void Growth
,”
Prog. Mater. Sci.
,
27
(
3–4
), pp.
189
244
.
33.
Muller
,
1995
, “
An Experimental and Analytical Investigation on the Fatigue Behavior of Fuselage Riveted Lap Joints
,”
Ph.D. thesis
,
Delft University of Technology, Delft
,
The Netherlands
.
34.
Chandrashekhara
,
K.
, and
Muthanna
,
S. K.
,
1977
, “
Stresses in a Thick Plate With a Circular Hole Under Axisymmetric Loading
,”
Int. J. Eng. Sci.
,
15
(
2
), pp.
135
146
.
You do not currently have access to this content.