The complexity of local and dynamic thermal transformations in additive manufacturing (AM) processes makes it difficult to track in situ thermomechanical changes at different length scales within a part using experimental process monitoring equipment. In addition, in situ process monitoring is limited to providing information only at the exposed surface of a layer being built. As a result, an understanding of the bulk microstructural transformations and the resulting behavior of a part requires rigorous postprocess microscopy and mechanical testing. In order to circumvent the limited feedback obtained from in situ experiments and to better understand material response, a novel 3D dislocation density based thermomechanical finite element framework has been developed. This framework solves for the in situ response much faster than currently used state-of-the-art modeling software since it has been specifically designed for AM platforms. This modeling infrastructure can predict the anisotropic performance of AM-produced components before they are built, can serve as a method to enable in situ closed-loop process control and as a method to predict residual stress and distortion in parts and thus enable support structure optimization. This manuscript provides an overview of these software modules which together form a robust and reliable AM software suite to address future needs for machine development, material development, and geometric optimization.
Skip Nav Destination
Article navigation
December 2014
Research-Article
An Integrated Approach to Additive Manufacturing Simulations Using Physics Based, Coupled Multiscale Process Modeling
Deepankar Pal,
Deepankar Pal
1
Assistant Professor
Department of Mechanical Engineering,
J.B. Speed School of Engineering,
e-mail: d0pal001@louisville.edu
Department of Mechanical Engineering,
J.B. Speed School of Engineering,
University of Louisville
,Louisville, KY 40292
e-mail: d0pal001@louisville.edu
1Corresponding author.
Search for other works by this author on:
Nachiket Patil,
Nachiket Patil
Senior Research Engineer
e-mail: nachiket.patil@3dsim.com
3DSIM, LLC
,201 E. Jefferson Street
,Louisville, KY 40202
e-mail: nachiket.patil@3dsim.com
Search for other works by this author on:
Kai Zeng,
Kai Zeng
Department of Industrial Engineering,
J.B. Speed School of Engineering,
e-mail: k0zeng01@louisville.edu
J.B. Speed School of Engineering,
University of Louisville
,Louisville, KY 40292
e-mail: k0zeng01@louisville.edu
Search for other works by this author on:
Brent Stucker
Brent Stucker
Clark Chair Professor
J. B. Speed School of Engineering,
e-mail: brent.stucker@louisville.edu
J. B. Speed School of Engineering,
University of Louisville
,Louisville, KY 40292
e-mail: brent.stucker@louisville.edu
Search for other works by this author on:
Deepankar Pal
Assistant Professor
Department of Mechanical Engineering,
J.B. Speed School of Engineering,
e-mail: d0pal001@louisville.edu
Department of Mechanical Engineering,
J.B. Speed School of Engineering,
University of Louisville
,Louisville, KY 40292
e-mail: d0pal001@louisville.edu
Nachiket Patil
Senior Research Engineer
e-mail: nachiket.patil@3dsim.com
3DSIM, LLC
,201 E. Jefferson Street
,Louisville, KY 40202
e-mail: nachiket.patil@3dsim.com
Kai Zeng
Department of Industrial Engineering,
J.B. Speed School of Engineering,
e-mail: k0zeng01@louisville.edu
J.B. Speed School of Engineering,
University of Louisville
,Louisville, KY 40292
e-mail: k0zeng01@louisville.edu
Brent Stucker
Clark Chair Professor
J. B. Speed School of Engineering,
e-mail: brent.stucker@louisville.edu
J. B. Speed School of Engineering,
University of Louisville
,Louisville, KY 40292
e-mail: brent.stucker@louisville.edu
1Corresponding author.
Contributed by the Manufacturing Engineering Division of ASME for publication in the JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING. Manuscript received April 21, 2014; final manuscript received September 12, 2014; published online October 24, 2014. Assoc. Editor: Joseph Beaman.
J. Manuf. Sci. Eng. Dec 2014, 136(6): 061022 (16 pages)
Published Online: October 24, 2014
Article history
Received:
April 21, 2014
Revision Received:
September 12, 2014
Citation
Pal, D., Patil, N., Zeng, K., and Stucker, B. (October 24, 2014). "An Integrated Approach to Additive Manufacturing Simulations Using Physics Based, Coupled Multiscale Process Modeling." ASME. J. Manuf. Sci. Eng. December 2014; 136(6): 061022. https://doi.org/10.1115/1.4028580
Download citation file:
Get Email Alerts
Effect of Microgravity on the Metal Droplet Transfer and Bead Characteristics in the Directed Energy Deposition-Arc Process
J. Manuf. Sci. Eng (December 2024)
Femtosecond Pulsed Laser Machining of Fused Silica for Micro-Cavities With Sharp Corners
J. Manuf. Sci. Eng (January 2025)
Acquired Angle Error Correction Based on Variation of an Angle Detection Signal Intensity in Rotary Encoders
J. Manuf. Sci. Eng (January 2025)
Related Articles
Enhanced Surface Integrity From Cryogenic Machining of AZ31B Mg
Alloy: A Physics-Based Analysis With Microstructure Prediction
J. Manuf. Sci. Eng (June,2017)
Inelastic Contact Behavior of Crystalline Asperities in rf MEMS Devices
J. Eng. Mater. Technol (January,2009)
A New Method for Elastic-Plastic Contact Analysis of a Deformable Sphere and a Rigid Flat
J. Tribol (April,2006)
Physics-Based Microstructure Simulation for Drilled Hole Surface in Hardened Steel
J. Manuf. Sci. Eng (August,2014)
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Microstructure Evolution and Physics-Based Modeling
Ultrasonic Welding of Lithium-Ion Batteries
List of Commercial Codes
Introduction to Finite Element, Boundary Element, and Meshless Methods: With Applications to Heat Transfer and Fluid Flow