For a range of precision machining and micromachining operations, the crystallographic anisotropy plays a critical role in determining the machining forces. Part II of this work presents the calibration and validation of the rate-sensitive plasticity-based machining (RSPM) model developed in Part I. The five material parameters, including four hardening parameters and the exponent of rate sensitivity, for both single-crystal aluminum and single-crystal copper are calibrated from the single-crystal plunge-turning data using a Kriging-based minimization approach. Subsequently, the RSPM model is validated by comparing the specific energies obtained from the model to those from a single-crystal cutting test. The RSPM model is seen to capture the experimentally observed variation of specific energies with crystallographic anisotropy (orientation), including the mean value, symmetry, specific trend, amplitude, and phase of the peak specific energy. The effects of lattice rotation, hardening, and material-parameter variations on the predicted specific energies is then analyzed, revealing the importance of both lattice rotation and hardening in accurately capturing the specific energies when cutting single-crystals. Using the RSPM model, the effects of crystallographic orientation, rake angle and friction angle on specific energies are also analyzed. Lastly, a simplified model that uses Merchant’s shear angle, thereby circumventing the minimization procedure, is constructed and evaluated.

References

References
1.
Williams
,
J.
, and
Horne
,
J.
, 1982, “
Crystallographic Effects in Metal Cutting
,”
J. Mater. Sci.
,
17
, pp.
2618
2624
.
2.
Cohen
,
P. H.
, 1982, “
The Orthogonal In-Situ Machining of Single and Polycrystalline Aluminum and Copper
,” Ph.D. thesis, Ohio State University, Columbus, OH.
3.
Sato
,
M.
,
Kato
,
Y.
, and
Tsutiya
,
K.
, 1979, “
Effects of Crystal Orientation on the Flow Mechanism in Cutting Aluminum Single Crystal
,”
Trans. Jpn. Inst. Met.
,
20
, pp.
414
422
.
4.
Sato
,
M.
,
Kato
,
Y.
,
Tsutiya
,
K.
, and
Aoki
,
S.
, 1981, “
Effects of Crystal Orientation on the Cutting Mechanism of Aluminum Single Crystal
,”
Bull. Jpn. Soc. Mech. Eng.
,
24
, pp.
1864
1870
.
5.
Sato
,
M.
,
Kato
,
Y.
,
Aoki
,
S.
, and
Ikoma
,
A.
, 1983, “
Effects of Crystal Orientation on the Cutting Mechanism of Aluminum Single Crystal
,”
Bull. Jpn. Soc. Mech. Eng.
,
26
(
215
), pp.
890
896
.
6.
Sato
,
M.
,
Yamazaki
,
T.
,
Shimizu
,
Y.
, and
Takabayashi
,
T.
, 1991, “
A Study on the Microcutting of Aluminum Single Crystals
,”
JSME Int. J., Ser. C
,
34
(
4
), pp.
540
545
.
7.
Lawson
,
B. L.
,
Kota
,
N.
, and
Ozdoganlar
,
O. B.
, 2008, “
Effects of Crystallographic Anisotropy on Orthogonal Micromachining of Single-Crystal Aluminum
,”
ASME J. Manuf. Sci. Eng.
,
130
(
3
), p.
031116
.
8.
Willams
,
J.
, and
Gane
,
N.
, 1977, “
Some Observations on the Flow Stress Of Metals During Metal Cutting
,”
Wear
,
42
, pp.
341
353
.
9.
Moriwaki
,
T.
,
Okuda
,
K.
, and
Shen
,
J. G.
, 1993, “
Study on Ultraprecision Orthogonal Microdiamond Cutting of Single-Crystal Copper
,”
JSME Int. J., Ser. C
,
36
, pp.
400
406
.
10.
Zhou
,
M.
, and
Ngoi
,
B. K. A.
, 2001, “
Effect of Tool and Workpiece Anisotropy on Microcutting Processes
,”
Proc. Inst. Mech. Eng., Part B
,
215
, pp.
13
19
.
11.
Ueda
,
K.
,
Iwata
,
K.
, and
Nakajama
,
K.
, 1980, “
Chip Formation Mechanism in Single Crystal Cutting β-Brass
,”
CIRP Ann.
,
29
(
1
), pp.
41
46
.
12.
Chandrasekharan
,
V.
,
Kapoor
,
S. G.
, and
Devor
,
R. E.
, 1995, “
A Mechanistic Approach to Predicting the Cutting Forces in Drilling: With Application to Fiber-Reinforced Composite Materials
,”
ASME J. Eng. Ind.
,
117
, pp.
559
570
.
13.
Sasena
,
M. J.
, 2002, “
Flexibility and Efficiency Enhancements for Constrained Global Design Optimization with Kriging Approximations
,” Ph.D thesis, University of Michigan, Ann Arbor.
14.
Kocks
,
U. F.
,
Tome
,
C. N.
, and
Wenk
,
H. R.
, eds., 1998,
Texture and Anisotropy: Preferred Orientations in Polycrystals and Their Effect on Materials Properties
,
Cambridge University Press
,
New York
.
15.
Kota
,
N.
, and
Ozdoganlar
,
O.
, 2010, “
A Model-Based Analysis of Orthogonal Cutting for Single-Crystal fcc Metals Including Crystallographic Anisotropy
,”
Mach. Sci. Technol.
,
14
(
1
), pp.
102
127
.
16.
Kota
,
N.
, and
Ozdoganlar
,
O.
, 2008, “
A Simplified Model for Orthogonal Micromachining of fcc Single-Crystal Materials
,”
Trans. NAMRI/SME.
,
36
, pp.
193
200
.
17.
Lee
,
W.
,
To
,
S.
, and
Cheung
,
C. F.
, 2000, “
Effect of Crystallographic Orientation in Diamond Turning of Copper Single Crystals
,”
Scr. Mater.
,
42
, pp.
937
945
.
You do not currently have access to this content.