A new experimental approach to identify the cutting dynamics in turning operations is presented. This method treats the problem as a closed-loop gray-box identification problem and is based upon spectral analysis and least squares estimation techniques. An active magnetic bearing is employed both to excite the system and to increase the tool’s damping. The inherent time delay of the cutting process is “removed” in identification by limiting the observation period to less than one revolution period of the workpiece. The coefficients of several cutting tests were identified. The methodology was validated by predicting the critical depth of cut from the identification results and comparing with the experiment result measured from a cutting test.
Issue Section:
Technical Papers
1.
Smith
, S.
, and Tlusty
, J.
, 1990, “Update on High-speed Milling Dynamics
,” ASME J. Eng. Ind.
0022-0817, 112
, pp. 142
–149
.2.
Fittro
, R. L.
, and Knospe
, C. R.
, 1998, “μ-Synthesis Control Design Applied to a High Speed Machining Spindle With Active Magnetic Bearing
,” 6th International Symposia on Magnetic Bearings, Cambridge, MA, USA
, pp. 449
–458
.3.
Ehmann
, K.
, Kapoor
, S.
, Devor
, R.
, and Lazoglu
, I.
, 1997, “Machining Process Modeling: A Review
,” ASME J. Manuf. Sci. Eng.
1087-1357, 119
, pp. 655
–663
.4.
Merritt
, H. E
, 1965, “Theory of Self-excited Machine-tool Chatter, Contribution to Machine-tool Chatter Research-1
,” Trans. ASME
0097-6822, 87
, pp. 447
–455
.5.
Tlusty
, J.
, 1978, “Analysis of the State of Research in Cutting Dynamics
,” CIRP Ann.
0007-8506, 27
, pp. 583
–589
.6.
Wu
, D. W.
, and Liu
, C. R.
, 1985, “An Analytical Model of Cutting Dynamics. Part 1: Model Building
,” ASME J. Eng. Ind.
0022-0817, 107
, pp. 107
–111
.7.
Sisson
, T. R.
, and Kegg
, R. L.
, 1969, “An Explanation of Low-speed Chatter Effects
,” ASME J. Eng. Ind.
0022-0817, 91
, pp. 951
–558
.8.
Yang
, X.
, and Eman
, K.
, 1985, “Analysis of Three-dimensional Cutting Process Dynamic
,” ASME J. Eng. Ind.
0022-0817, 107
, pp. 336
–342
.9.
Minis
, I.
, Magrab
, E.
, and Pandelidis
, I.
, 1990, “Improved Methods for the Prediction of Chatter in Turning, Part 2: Determination of Cutting Process Parameters
,” ASME J. Eng. Ind.
0022-0817, 112
, pp. 21
–27
.10.
Marchelek
, K.
, and Tomkow
, J.
, 1993, “Experimental Investigations in Cutting Dynamics
,” ASME J. Eng. Ind.
0022-0817, 115
, pp. 508
-511
.11.
Gustavsson
, I.
, Ljung
, L.
, and Soderstrom
, T.
, 1977, “Survey Paper: Identification Processes in Closed Loop, Identifiability and Accuracy Aspects
,” Automatica
0005-1098, 13
, pp. 59
–75
.12.
Forssell
, U.
and Ljung
, L.
, 1999, “Closed-loop Identification Revisited
,” Automatica
0005-1098, 35
, pp. 1215
–1241
.13.
Van Brussel
, H.
, and Vanherck
, P.
, 1971, “A New Method for the Determination of the Dynamics Cutting Coefficient
,” 12th MTFR Conference, Manchester
.14.
Ahn
, T.
, and Eman
, K.
, 1985, “Cutting Dynamics Identification by Dynamics Data System (DDS) Modeling Approach
,” ASME J. Eng. Ind.
0022-0817, 107
, pp. 91
–94
.15.
Ahn
, T.
, and Eman
, K.
, 1987, “Determination of Inner and Outer Modulation Dynamics in Orthogonal Cutting
,” ASME J. Eng. Ind.
0022-0817, 109
, pp. 275
–280
.16.
Cho
, D.
, and Eman
, K.
, 1990, “In-Process Identification of the Milling Operation
,” Int. J. Mach. Tools Manuf.
0890-6955, 30
(3
), pp. 325
–337
.17.
Minis
, I.
, Magrab
, E.
, and Pandelidis
, I.
, 1990, “Improved Methods for the Prediction of Chatter in Turning, Part 3: A Generalized Linear Theory
,” ASME J. Eng. Ind.
0022-0817, 112
, pp. 28
–35
.18.
Kay
, S. M.
, 1988, Modern Spectrum Estimation: Theory and Application
, Prentice-Hall
, Engle wood Cliffs, NJ.19.
Bowerman
, B.
, and O’Connell
, R.
, 1990, Linear Statistical Models—An Applied Approach
, 2nd ed., PWS-KENT Publishing Company
, Pacific Grove, CA.20.
Karimi
, A.
, and Landau
, I.
, 1998, “Comparison of the Closed-loop Identification Methods in Terms of the Bias Distribution
,” Syst. Control Lett.
0167-6911, 34
, pp. 159
–167
.21.
Young
, T.
, Mathew
, P
, and Oxley
, P.
, 1987, “Allowing for Nose Radius Effects in Predicting the Chip Flow Direction and Cutting Forces in Bar Turning
,” Proc. Inst. Mech. Eng., Part C: Mech. Eng. Sci.
0263-7154, 120
, pp. 213
–226
.22.
Boothroyd
, G.
, and Knight
, A.
, 1989, Fundamental of Machining and Machine Tools
, Marcel Dekker, Inc.
, New york.23.
Ogata
, K.
, 1970, Modern Control Engineering
, Prentice-Hall
, Englewood Cliffs, NJ.24.
Ljung
, L.
, 1987, System Identification-Theory for the User
, Prentice-Hall
, Englewood Cliffs, NJ.Copyright © 2005
by American Society of Mechanical Engineers
You do not currently have access to this content.
