This paper presents a formability analysis of tailor-welded blanks (TWBs) made of cold rolled steel sheets with varying thicknesses. Steel sheets ranging between 0.5 mm, 0.6 mm, 0.7 mm, 0.8 mm, 0.9 mm, and 1.0 mm in thickness were used to produce TWBs of different thickness combinations. The primary objective of this paper is to characterize the effects of thickness ratios on the forming limit diagram (FLD) for a particular type of TWB. The TWBs chosen for the investigation are designed with the weld line located in the center of the specimens perpendicular to the principal strain direction. Nd:YAG laser butt-welding was used to prepare different tailor-made blank specimens for uniaxial tensile tests and Swift tests. The experimental results of the uniaxial tensile test clearly revealed that there were no significant differences between the tensile strengths of TWBs and those of the base metals. After the Swift tests, the formability of TWBs was analyzed in terms of two measures: The forming limit diagram and minimum major strain. The experimental findings indicated that the higher the thickness ratio, the lower the level of the forming limit curve (FLC) and the lower the formability of the TWBs. The findings also show an inverse proportional relationship between thickness ratios and minimum major strains. TWBs with a thickness ratio of close to 1 were found to have a minimum major strain closer to those of base metals. The effects of different thickness ratios on TWBs were further analyzed with a finite element code in a computer-aided engineering package, PAM-STAMP, while the failure criteria of the TWBs in the finite element analysis were addressed by the FLCs which were obtained from the experiments. However, the weld of the TWB in the simulation was simply treated as a thickness step, whereas its heat affected zones were sometimes disregarded, so that the effects of the thickness ratio could be significantly disclosed without the presence of weld zones. The results of the simulation should certainly assist to clarify and explain the effects of different thickness ratios on TWBs.
Skip Nav Destination
e-mail: mflcchan@inet.polyu.edu.hk
Article navigation
November 2005
Technical Papers
Formability Analysis of Tailor-Welded Blanks of Different Thickness Ratios
L. C. Chan,
L. C. Chan
Department of Industrial and Systems Engineering,
e-mail: mflcchan@inet.polyu.edu.hk
The Hong Kong Polytechnic University
, Hong Kong, China
Search for other works by this author on:
C. H. Cheng,
C. H. Cheng
Department of Industrial and Systems Engineering,
The Hong Kong Polytechnic University
, Hong Kong, China
Search for other works by this author on:
S. M. Chan,
S. M. Chan
Department of Industrial and Systems Engineering,
The Hong Kong Polytechnic University
, Hong Kong, China
Search for other works by this author on:
T. C. Lee,
T. C. Lee
Department of Industrial and Systems Engineering,
The Hong Kong Polytechnic University
, Hong Kong, China
Search for other works by this author on:
C. L. Chow
C. L. Chow
Department of Mechanical Engineering,
University of Michigan-Dearborn
, 4901 Evergreen Road, Dearborn, MI
Search for other works by this author on:
L. C. Chan
Department of Industrial and Systems Engineering,
The Hong Kong Polytechnic University
, Hong Kong, Chinae-mail: mflcchan@inet.polyu.edu.hk
C. H. Cheng
Department of Industrial and Systems Engineering,
The Hong Kong Polytechnic University
, Hong Kong, China
S. M. Chan
Department of Industrial and Systems Engineering,
The Hong Kong Polytechnic University
, Hong Kong, China
T. C. Lee
Department of Industrial and Systems Engineering,
The Hong Kong Polytechnic University
, Hong Kong, China
C. L. Chow
Department of Mechanical Engineering,
University of Michigan-Dearborn
, 4901 Evergreen Road, Dearborn, MIJ. Manuf. Sci. Eng. Nov 2005, 127(4): 743-751 (9 pages)
Published Online: February 4, 2005
Article history
Received:
May 25, 2004
Revised:
February 4, 2005
Citation
Chan, L. C., Cheng, C. H., Chan, S. M., Lee, T. C., and Chow, C. L. (February 4, 2005). "Formability Analysis of Tailor-Welded Blanks of Different Thickness Ratios." ASME. J. Manuf. Sci. Eng. November 2005; 127(4): 743–751. https://doi.org/10.1115/1.2034518
Download citation file:
Get Email Alerts
Related Articles
Numerical Simulations and Experimental Results of Tensile Test Behavior of Laser Butt Welded DP980 Steels
J. Eng. Mater. Technol (October,2008)
Formability and Weld Zone Analysis of Tailor-Welded Blanks for Various Thickness Ratios
J. Eng. Mater. Technol (April,2005)
Analysis of Tube Hydroforming by Means of an Inverse Approach
J. Manuf. Sci. Eng (May,2003)
Experimental and Theoretical Analysis on Formability of Aluminum Tailor-Welded Blanks
J. Eng. Mater. Technol (January,2007)
Related Proceedings Papers
Related Chapters
Study on Weld-Line Movement of TWBs with Different Thickness in Hydro-Forming Deep Drawing of Square Cup
International Conference on Mechanical Engineering and Technology (ICMET-London 2011)
Software Reuse in Computer Aided Testing System
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)
STRUCTURAL RELIABILITY ASSESSMENT OF PIPELINE GIRTH WELDS USING GAUSSIAN PROCESS REGRESSION
Pipeline Integrity Management Under Geohazard Conditions (PIMG)