Estimating error uncertainties arising in production parts is not a well-understood process. An approach to estimate these uncertainties was developed in this study. Machine tool error components were measured on a three-axis vertical machining center. Multiple parts were produced on the measured machining center then measured on a coordinate measuring machine. Uncertainty models for hole-center to hole-center lengths and orthogonalities were developed using measured machine tool errors. These estimated uncertainties were compared against measured uncertainties. The main conclusion from the study is that the Law of Propagation of Uncertainties can be used to estimate machining uncertainties.
Issue Section:
Technical Papers
1.
International Organization for Standardization, Guide to the Expression of Uncertainty in Measurement.
2.
Taylor, B. N., and Kuyatt, C. E., 1994, “Guidelines for Evaluating and Expressing the Uncertainty of NIST Measurement Results,” NIST Technical Note 1297, National Institute of Standards and Technology, Gaithersburg, MD, 20899.
3.
American National Standards Institute, 1997, “American National Standard for Expressing Uncertainty—U.S. Guide to the Expression of Uncertainty in Measurement,” ANSI/NCSL Z540-2-1997.
4.
Gilsinn, D. E., and Ling, A. V., 2002, “Comparative Statistical Analysis of Test Parts Manufactured in Production Environments,” NISTIR 6868, National Institute of Standards and Technology, Gaithersburg, MD, 20899-8910.
5.
Wilhelm
, R. G.
, Srinivasan
, N.
, and Farabaugh
, F.
, 1997
, “Part Form Errors Predicted From Machine Tool Performance Measurements
,” CIRP Ann.
, 46
, pp. 471
–474
.6.
Chatterjee
, S.
, 1997
, “An Assessment of Quasi-Static and Operational Errors in NC Machine Tools
,” J. Manuf. Syst.
, 16
(1
), pp. 59
–68
.7.
Shin
, Y. C.
, and Wei
, Y.
, 1992
, “A Statistical Analysis of Positional Errors of a Multiaxis Machine Tool
,” Precis. Eng.
, 14
, pp. 139
–146
.8.
Kaminski
, J.
, and Crafoord
, R.
, 1991
, “Position Accuracy of Drilled Holes
,” CIRP Ann.
, 40
, pp. 503
–506
.9.
Lehtihet
, E. A.
, and Gunasena
, U. N.
, 1990
, “Statistical Models for the Relationship Between Production Errors and the Position Tolerance of a Hole
,” CIRP Ann.
, 39
, pp. 569
–572
.10.
Lee
, S. J.
, Eman
, K. F.
, and Wu
, S. M.
, 1987
, “An Analysis of the Drill Wandering Motion
,” ASME J. Eng. Ind.
, 109
, pp. 297
–305
.11.
Fujii
, H.
, Marui
, E.
, and Ema
, S.
, 1986
, “Whirling Vibration in Drilling, Part 1: Cause of Vibration and Role of Chisel Edge
,” ASME J. Eng. Ind.
, 108
, pp. 157
–162
.12.
Fujii
, H.
, Marui
, E.
, and Ema
, S.
, 1986
, “Whirling Vibration in Drilling, Part 2: Influence of Drill Geometries, Particularly of the Drill Flank, on the Initiation of Vibration
,” ASME J. Eng. Ind.
, 108
, pp. 163
–168
.13.
Fujii
, H.
, Marui
, E.
, and Ema
, S.
, 1988
, “Whirling Vibration in Drilling, Part 3: Vibration Analysis in Drilling Workpiece With a Pilot Hole
,” ASME J. Eng. Ind.
, 110
, pp. 315
–321
.14.
Magrab
, E. B.
, and Gilsinn
, D. E.
, 1984
, “Buckling Loads and Natural Frequencies of Drill Bits and Fluted Cutters
,” ASME J. Eng. Ind.
, 106
, pp. 196
–204
.15.
Shen
, Y.
, and Duffie
, N. A.
, 1995
, “An Uncertainty Analysis Method for Coordinate Referencing in Manufacturing Systems
,” ASME J. Eng. Ind.
, 117
, pp. 42
–48
.16.
Shen
, Y.
, and Duffie
, N. A.
, 1991
, “Uncertainties in the Acquisition and Utilization of Coordinate Frames in Manufacturing Systems
,” CIRP Ann.
, 40
(1
), pp. 527
–530
.17.
Bauer
, W. F.
, 1958
, “The Monte Carlo Method
,” J. Soc. Ind. Appl. Math.
, 6
(4
), pp. 438
–451
.18.
Yau
, H.
, 1997
, “Evaluation and Uncertainty Analysis of Vectorial Tolerances
,” Precis. Eng.
, 20
, pp. 123
–137
.19.
Phillips
, S. D.
, Borchardt
, B.
, Estler
, W. T.
, and Buttress
, J.
, 1998
, “The Estimation of Measurement Uncertainty of Small Circular Features Measured by Coordinate Measuring Machines
,” Precis. Eng.
, 22
, pp. 87
–97
.20.
ASME B5.54-1992, 1993, Methods for Performance Evaluation of Computer Numerically Controlled Machining Centers, The American Society of Mechanical Engineers, New York.
21.
Ziegert
, J. C.
, and Mize
, C. D.
, 1994
, “The Laser Ball Bar: A New Instrument for Machine Tool Metrology
,” Precis. Eng.
, 16
, pp. 259
–267
.22.
Srinivasa
, N.
, and Ziegert
, J. C.
, 1996
, “Automated Measurement and Compensation of Thermally Induced Error Maps in Machine Tools
,” Precis. Eng.
, 19
, pp. 112
–132
.23.
Schmitz
, T.
, and Ziegert
, J.
, 1998
, “Premachining Computer Numerical Control Contour Validation
,” Precis. Eng.
, 22
, pp. 10
–18
.24.
Donmez, M. A., 1985, “A General Methodology for Machine Tool Accuracy Enhancement: Theory, Application and Implementation,” Ph.D. Thesis, Purdue University.
25.
Coleman, H. W., and Steele, W. G., 1999, Experimentation and Uncertainty Analysis for Engineers, John Wiley & Sons, Inc., New York.
26.
Wheeler, A. J., and Ganji, A. R., 1996, Introduction to Engineering Experimentation, Prentice Hall, Englewood Cliffs.
27.
Montgomery, D. C., and Peck, E. A., 1992, Introduction to Linear Regression Analysis, John Wiley & Sons, Inc., New York.
28.
Mandel
, J.
, 1984
, “Fitting Straight Lines When Both Variables are Subject to Error
,” J. Quality Technol.
, 16
, pp. 1
–14
.29.
Dixon, W. J., and Massey, Jr., F. J., 1957, Introduction to Statistical Analysis, McGraw-Hill Book Company, Inc., New York.
30.
Mood, A. M., and Graybill, F. A., 1963, Introduction to the Theory of Statistics, McGraw-Hill Book Company, Inc., New York.
Copyright © 2004
by ASME
You do not currently have access to this content.
