This paper addresses the reinforcement of photopolymers, through the addition of short glass fibers, for Rapid Layered Composite parts Manufacturing (RLCM). Novel designs for an (external) fiber-resin-mixing subsystem and a (slot-coating-based) liquid-layer-formation subsystem are presented. These subsystems, when used as integral parts of a lithography-based RLCM system, successfully cope with typical difficulties encountered in the formation of thin layers from a highly viscous fiber-photopolymer composite liquid. Axiomatic Design theory was utilized for the analysis of both subsystem designs. Verification experiments run on an RLCM system confirmed (i) the ability of the fiber-resin-mixing subsystem to supply liquid composite with specified fiber content and to avoid fiber degradation through breakage, as well as (ii) the ability of the liquid-layer-formation subsystem to form solid layers with high fiber content and of uniform thickness.

1.
Zak
,
G.
,
Sela
,
M. N.
,
Vevko
,
V.
,
Park
,
C. B.
, and
Benhabib
,
B.
,
1999
, “
Layered-Manufacturing of Fiber-Reinforced Composites
,”
ASME J. Manuf. Sci. Eng.
,
121
, pp.
448
456
.
2.
Zak
,
G.
,
Park
,
C. B.
, and
Benhabib
,
B.
,
2000
, “
Mechanical Properties of Short-Fiber Layered Composites
,”
Rapid Prototyping J.
,
6
(
2
), pp.
107
118
.
3.
Suh, N. P., 1990, The Principles of Design, New York, NY: Oxford University Press Inc.
4.
Agarwall, B. D., and Broutman, L. J., 1990, “
Analysis and Performance of Fiber Composites,” 2nd ed., New York, NY, John Wiley & Sons.
5.
Renault
,
T.
,
Ogale
,
A. A.
,
Dooly
,
R. L.
,
Bagchi
,
A.
, and
Jara-Almonte
,
C. C.
, 1991, “Photolithography for Composites Manufacturing: Continuous Glass Fiber/Polyacrylate Composites,” SAMPE Q., January, pp. 19–25.
6.
Renault
,
T.
, and
Ogale
,
A. A.
, 1991, “3-D Photolithography for Composite Development: Discontinuous Reinforcements,” SAMPE Q., October, pp. 28–38.
7.
Barlage, W. B., Jara-Almonet, C. C., Bagchi, A., Ogale, A. A., and Dodey, R. L., 1992, “
Fiber/Resin Composite Manufacturing Using Solid Freeform Fabrication,” Third International Conference on Rapid Prototyping, Dayton, Ohio, pp. 15–24.
8.
Charan, R., Renault, T., Ogale, A. A., and Bagchi, A., 1994, “Automated Fiber-Reinforced Composite Prototypes,” Fifth International Conference on Rapid Prototyping, Dayton, Ohio, pp. 91–97.
9.
Klosterman, D., Chartoff, R., Priore, B., Osborne, N., and Graves, G., 1996, “Structural Composites via Laminated Object Manufacturing (LOM),” Solid Freeform Fabrication Symposium Proceedings, Austin, Texas, pp. 105–115.
10.
Brown
,
J. H.
, and
Colton
,
J. S.
,
2000
, “
A Machine System for the Rapid Production of Composite Structures
,”
Polym. Compos.
,
21
(
1
), pp.
124
133
.
11.
Zak
,
G.
,
Chan
,
A. Y. F.
,
Park
,
C. B.
, and
Benhabib
,
B.
,
1996
, “
Viscosity Analysis of Photopolymer and Glass-Fiber Composites for Rapid Layered Manufacturing
,”
Rapid Prototyping J.
,
2
(
3
), pp.
16
23
.
12.
Gray
,
R. W.
,
Donald
,
G. B.
, and
Bohn
,
H. G.
,
1998
, “
Effects of Processing Conditions on Short TLCP Fiber Reinforced FDM Parts
,”
Rapid Prototyping J.
,
4
(
1
), pp.
14
25
.
13.
Zhong
,
W.
,
Li
,
F.
,
Zhang
,
Z.
,
Song
,
L.
, and
Li
,
Z.
,
2001
, “
Short Fiber Reinforced Composites for Fused Deposition Modelling
,”
Mater. Sci. Eng., A
,
301
(
2
), pp.
125
130
.
14.
Klosterman, D., Priore, B., and Chartoff, R., 1997, “Laminated Object Manufacturing of Polymer Matrix Composites,” Proceedings of the Seventh International Conference on Rapid Prototyping, San Francisco, CA, pp. 283–292.
15.
Klosterman, D., Chartoff, R., Flach, L., and Bryant, E., 2000, “Model-based Control of Cure Distribution in Polymer Composite Parts Made by Laminated Object Fabrication (LOF),” Solid Freeform Fabrication Symposium, University of Texas at Austin.
16.
Ditl
,
P.
, and
Nauman
,
B. E.
,
1992
, “
Off-Bottom Suspension of Thin Sheets
,”
AIChE J.
,
38
(
6
, pp.
959
965
.
17.
Tay
,
M.
,
Deutchlander
,
B.
, and
Tatterson
,
B.
, 1984, “Suspension Characteristics of Large Cylinders in Agitated Tanks,” Chem. Eng. Commun. 29 cited in Ditl and Nauman 1992 .
18.
Nienow, A. W., 1997, “The Suspension of Solid Particles,” Mixing in the Process Industries, 2nd ed., Harnby, N., Edwards, M. F., and Nienow, A. E., eds., London, Butterworth Heinemann.
19.
Bohnet
,
M.
, and
Niesmak
,
G.
, 1980, “Distribution of Solids in Stirred Suspensions,” German Chemical Engineering, 3, pp. 57–65.
20.
McDonough, R. J., 1992, Mixing for the Process Industries, New York, NY, Van Nostrand Reinhold.
21.
Chudacek
,
M. W.
, 1984, “Does Your Tank Bottom Have the Right Shape?” Chem. Eng, October, pp. 79–83.
22.
Ibrahim
,
S.
, and
Nienow
,
A. W.
,
1996
, “
Particle Suspension in the Turbulent Regime
,”
Trans. Inst. Chem. Eng.
,
74
, pp.
679
688
.
23.
Ranade
,
V. V.
,
Mishra
,
V. P.
,
Saraph
,
V. S.
,
Deshpande
,
G. B.
, and
Joshi
,
J. B.
,
1992
, “
Comparison of Axial Flow Impellers Using a Laser Doppler Anemometer
,”
Ind. Eng. Chem. Res.
31
, pp.
2370
2379
.
24.
Armenante
,
P. M.
, and
Nagamine
,
E. U.
,
1997
, “
Effect of Low Off-Bottom Impeller Clearance on the Minimum Agitation Speed for Complete Suspension of Solids in Stirred Tanks
,”
Chem. Eng. Sci.
,
53
(
9
), pp.
1757
1775
.
25.
Tiljander
,
P.
, and
Theliander
,
H.
,
1993
, “
Power consumption and solid suspensions in completely filled vessels
,”
Chem. Eng. Commun.
,
124
, pp.
1
14
.
26.
Bakker
,
A.
, and
Myers
,
K.
,
1998
, “
Solids Suspension with Up-Pumping Pitched Blade and High-Efficiency Impellers
,”
Can. J. Chem. Eng.
,
76
(
3
), pp.
433
440
.
27.
Levins
,
D. M.
, and
Glastonbury
,
J. R.
,
1972
, “
Application of Kolmogoroff’s Theory to Particle-Liquid Mass Transfer in Agitated Vessels
,”
Chem. Eng. Sci.
,
27
, pp.
537
543
.
28.
Sullivan
,
T. S.
,
Middleman
,
S.
, and
Keunings
,
R.
,
1987
, “
Use of Finite-Element Method to Interpret Rheological Effects in Blade Coating
,”
AIChE J.
,
33
(
12
), pp.
2047
2056
.
29.
Wang, F. F. Y., ed., 1976, Treatise on Materials Science and Technology: Volume 9—Ceramic Fabrication Processes, Academic Press, New York.
30.
Giavedoni
,
M. D.
, and
Satia
,
F. A.
,
1992
, “
Interfacial Viscosity in Viscous Free Surface Flows: A Sample Case
,”
Ind. Eng. Chem. Res.
31
(
9
), pp.
2222
2231
.
31.
Wang, F. J., and Domoto, G. A., 1995, “Flow Stability of Slot Coating—A Numerical Study,” Proceedings of the 1995 ASME/JSME Fluids Engineering and Laser Anemometry Conference and Exhibition, Hilton Head, SC, Vol. 217, pp. 143–150.
32.
Renap
,
K.
, and
Kruth
,
J. P.
,
1995
, “
Recoating Issues in Stereolithography
,”
Rapid Prototyping J.
,
1
(
3
), pp.
4
16
.
33.
Haberer, M., 2001, “Fiber-Resin Mixing and Layer Formation Subsystems for the Rapid Manufacturing of Short-Fiber-Reinforced Parts, M. A. Sc. Dissertation, Department of Mechanical and Industrial Engineering, University of Toronto.
You do not currently have access to this content.