Skip Nav Destination
Issues
May 2012
ISSN 1546-962X
In this Issue
Research Papers
Fundamentals of Biobased and Biodegradable Lubricants: A Real World Perspective
J. ASTM Int.. May 2012, 9(5): 1–6.
doi: https://doi.org/10.1520/JAI103578
Methods to Increase the Fatigue Life of Friction Stir Lap Welds in No-load Transfer Coupons Using a Retractable Pin Tool
J. ASTM Int.. May 2012, 9(5): 1–16.
doi: https://doi.org/10.1520/JAI103899
Estimation of Corrosion Fatigue-Crack Growth through Frequency Shedding Method
J. ASTM Int.. May 2012, 9(5): 1–13.
doi: https://doi.org/10.1520/JAI103988
A Broad-Group Cross-Section Library Based on ENDF/B-VII.0 for Fast Neutron Dosimetry Using the CPXSD Methodology
J. ASTM Int.. May 2012, 9(5): 1–9.
doi: https://doi.org/10.1520/JAI104060
Weathering Evaluation of Structural Silicone Sealants Used in Korea
J. ASTM Int.. May 2012, 9(5): 1–10.
doi: https://doi.org/10.1520/JAI104101
Development and Testing of the VITAMIN-B7/BUGLE-B7 Coupled Neutron-Gamma Multigroup Cross-Section Libraries
J. ASTM Int.. May 2012, 9(5): 1–10.
doi: https://doi.org/10.1520/JAI104130
A Review of the Behavior of Structural Silicone Glazing Systems Subjected to a Mega-Earthquake
J. ASTM Int.. May 2012, 9(5): 1–23.
doi: https://doi.org/10.1520/JAI104151
Development of an Active Detector for the Characterization of the Late-Time Radiation Environment from a Reactor Pulse
J. ASTM Int.. May 2012, 9(5): 1–7.
doi: https://doi.org/10.1520/JAI104164
Neutron Flux Reduction Programs for Reactor Pressure Vessel of Korea Nuclear Unit 1
J. ASTM Int.. May 2012, 9(5): 1–10.
doi: https://doi.org/10.1520/JAI104176
New Surface Samplers for Use in Forensic Sampling after a Chemical Incident
J. ASTM Int.. May 2012, 9(5): 1–9.
doi: https://doi.org/10.1520/JAI104217
Fatigue Sensitivity to Small Defects of a Gamma–Titanium–Aluminide Alloy
J. ASTM Int.. May 2012, 9(5): 1–12.
doi: https://doi.org/10.1520/JAI104293
Use of Ultrasound Thermometry to Study Natural Convection in Opaque Nanofluids
J. ASTM Int.. May 2012, 9(5): 1–12.
doi: https://doi.org/10.1520/JAI104320
Evaluation of Chlorella Minutissima Oil for Biodiesel Production
J. ASTM Int.. May 2012, 9(5): 1–6.
doi: https://doi.org/10.1520/JAI104322
Optimization of Biodiesel Production by Response Surface Methodology and Genetic Algorithm
J. ASTM Int.. May 2012, 9(5): 1–7.
doi: https://doi.org/10.1520/JAI104328
Comparison of the Performance of Copper Oxide Nanofluid with Water in Electronic Cooling
J. ASTM Int.. May 2012, 9(5): 1–15.
doi: https://doi.org/10.1520/JAI104342
Boundary-Layer Flow of a Nanofluid past a Stretching Sheet under Uniform Heat and Mass Flux
J. ASTM Int.. May 2012, 9(5): 1–9.
doi: https://doi.org/10.1520/JAI104363
Effect of Addition of Aluminum Nanoparticles on Cooling Performance and Quench Severity of Water during Immersion Quenching
J. ASTM Int.. May 2012, 9(5): 1–9.
doi: https://doi.org/10.1520/JAI104404
Nucleate Pool Boiling Heat Transfer Correlation for TiO2-Water Nanofluids
J. ASTM Int.. May 2012, 9(5): 1–12.
doi: https://doi.org/10.1520/JAI104409
Synthesis of Copper Nanofluids Using Ascorbic Acid Reduction Method Via One Step Solution Phase Approach
J. ASTM Int.. May 2012, 9(5): 1–13.
doi: https://doi.org/10.1520/JAI104416
Reduction of Emission in a Diesel Engine Using Nanofuel – Ceria Nanoparticle Dispersed Diesel
J. ASTM Int.. May 2012, 9(5): 1–9.
doi: https://doi.org/10.1520/JAI104424
Preparation and Characterization of Surfactant Coated Ce-Zr Nanoparticles and Nanofuel
J. ASTM Int.. May 2012, 9(5): 1–11.
doi: https://doi.org/10.1520/JAI104429
Thermal Conductivity and Rheological Behaviour of Al-alloy Dispersed Ethylene Glycol Based Nanofluids
J. ASTM Int.. May 2012, 9(5): 1–13.
doi: https://doi.org/10.1520/JAI104435
Optimum CNT Concentration and Bath Temperature for Maximum Heat Transfer Rate during Quenching in CNT Nanofluids
J. ASTM Int.. May 2012, 9(5): 1–12.
doi: https://doi.org/10.1520/JAI104442
Flow Visualization, Critical Heat Flux Enhancement, and Transient Characteristics in Pool Boiling Using Nanofluids
J. ASTM Int.. May 2012, 9(5): 1–16.
doi: https://doi.org/10.1520/JAI104443
Influence of the Reaction Conditions on the Ester Content and Characterization of Biodiesel via Ethylic Route
J. ASTM Int.. May 2012, 9(5): 1–8.
doi: https://doi.org/10.1520/JAI104452
Fuel Quality Assessment of Ethyl Esters Produced from Vegetable Oils and Their Blends With Petroleum Diesel
J. ASTM Int.. May 2012, 9(5): 1–14.
doi: https://doi.org/10.1520/JAI104528
Metrological Approach in the Study of Biodiesel Viscosity Variation with Temperature
D. M. E. Santo Filho, C. R. C. Rodrigues, A. P. F. Barbosa, J. J. P. dos Santos, Jr., F. O. Baldner, R. G. Pereira, C. S. C. Castro, J. R. R. Siqueira, R. J. Daroda, L. S. Lima
J. ASTM Int.. May 2012, 9(5): 1–15.
doi: https://doi.org/10.1520/JAI104612
Technical Notes
Easy Ambient Sonic-Spray Ionization Mass Spectrometry: An Alternative Method to Quantify Organic Impurities in Biodiesel
Rosana M. Alberici, Vanderlea de Souza, Lenise V. Gonçalves, Valnei S. Cunha, Marcos N. Eberlin, Romeu J. Daroda
J. ASTM Int.. May 2012, 9(5): 1–8.
doi: https://doi.org/10.1520/JAI104552
Discussion
Closure
Critical Assessment of the Standard ASTM E 399
J. ASTM Int. (April 2005)
Effects of Contamination on Aerospace Hydraulic Component and System Performance
J. ASTM Int. (October 2008)
Microstructural Stability of M5™ Alloy Irradiated up to High Neutron Fluences
J. ASTM Int. (July 2005)