A compartmented cooling coil is a single undivided coil section located in an intermediate point between the upstream and downstream sections of the air handling unit. A thermally insulated metal barrier is provided for the separation of two different air streams that are conditioned through the coil. The coolant flow through the heat exchanger is such that both the air streams encounter each pass of the coolant feed. This paper aims to address the performance of a compartmented coil through the concept of fin efficiency. The compartmented coil geometry involves two distinct sets of air-side characteristics coupled with one set of coolant-side characteristics and it is practically difficult to obtain the values of fin efficiency through empirical measurements alone over a wide range of operating conditions. Hence, the conventional methods of evaluation resort to numerical models for predicting fin performance. The paper questions the validity of certain fundamental assumptions based on which conventional models have been formulated to obtain the local heat transfer coefficient values. A simplified numerical model is formulated and evaluated using a Monte Carlo simulation approach. Performance curves across all ranges of input values are presented and empirical results are used to validate these curves at intermediate values. Results show that air face velocity and surface temperature at a given point on the fin has significant impact on the heat transfer coefficient. It is also shown that for a given fin height of $9.5mm$, the assumption of an average heat transfer coefficient as calculated from the LMTD method could vary significantly up to 10% from the predicted results.

1.
Gardner
,
K. A.
, 1945, “
Efficiency of Extended surfaces
,”
Trans. ASME
0097-6822,
67
, pp.
621
631
.
2.
Rich
,
D. G.
, 1966, “
The Efficiency and Thermal Resistance of Annular and Rectangular Fins
,”
Proceedings of the 3rd International Heat Transfer Conference
, Chicago, Vol.
3
, p.
281
.
3.
Manzoor
,
M.
, 1984,
Heat Flow Through Extended Surface Heat Exchangers
Springer
,
Berlin
.
4.
Stones
,
P. R.
, 1980, Ph.D. thesis, University of Leeds.
5.
Hassan
,
A.
, and
Siren
,
K.
, 2003, “
Performance Investigation of Plain and Finned Tube Evaporatively Cooled Heat Exchangers
,”
Appl. Therm. Eng.
1359-4311,
23
, pp.
325
340
.
6.
McQuiston
,
F. C.
, 1975, “
Fin Efficiency with Combined Heat and Mass Transfer
,”
ASHRAE Trans.
0001-2505,
81
(
1
), p.
350
.
7.
Huang
,
L. J.
, and
Shah
,
R. K.
, 1992, “
Assessment of Calculation Methods for Efficiency of Straight Fins of Rectangular Profile
,”
Int. J. Heat Fluid Flow
0142-727X,
13
, pp.
282
293
.
8.
Uma Maheswaran
,
C. R.
,
, and
Sekhar
,
S. C.
, 2006, “
Evaluation of Concepts of Fin Efficiency Using Monte Carlo Simulation Method
,”
Int. J. Heat Mass Transfer
0017-9310,
49
(
9
), pp.
1643
1646
.
9.
Sekhar
,
S. C.
,
Uma Maheswaran
,
C. R.
,
,
Tham
,
K. W.
, and
Cheong
,
K. W.
, 2004, “
Development of Energy Efficient Single Coil Twin Fan Air-conditioning System with Zonal Ventilation Control
,”
ASHRAE Trans.
0001-2505,
110
, Part 2, pp.
204
217
.
10.
Mokheimer
,
E. M. A.
, 2002, “
Performance of annular fins with different profiles subject to variable heat transfer coefficient
,”
Int. J. Heat Mass Transfer
0017-9310,
45
, pp.
3631
3642
.
11.
Kundu
,
B.
, and
Das
,
P. K.
, 2002, “
Performance Analysis and Optimization of Straight Taper Fins with Variable Heat Transfer Coefficient
,”
Int. J. Heat Mass Transfer
0017-9310,
45
, pp.
4739
4751
.
12.
Jambunathan
,
K.
,
Hartle
,
S.
,
Frost
,
A.
, and
Fontama
,
V. N.
, 1996, “
Evaluating Convective Heat Transfer Coefficients Using Neural Networks
,”
Int. J. Heat Mass Transfer
0017-9310,
39
(
11
), pp.
2329
2332
.
13.
Ma
,
S. W.
,
Bebhahani
,
A. I.
, and
Tsuei
,
Y. G.
, 1991, “
Two Dimensional Rectangular Fin with Variable Heat Transfer Coefficient
,”
Int. J. Heat Mass Transfer
0017-9310,
34
, pp.
79
.
14.
Barrow
,
H.
, 1986, “
Theoretical Solution for the Temperature in a Straight Fin with Variable Surface Heat Transfer Coefficient
,”
J. Heat Recovery Syst.
0198-7593,
6
(
6
), pp.
465
468
.
15.
Brian
,
V.
, and
Wells
,
R. G.
, 1986, “
Laminar Flow with an Axially Varying Heat Transfer Coefficient
,”
Int. J. Heat Mass Transfer
0017-9310,
29
(
12
), pp.
1881
1889
.
16.
Ghai
,
M. L.
, 1951, “
Heat Transfer in Straight Fins
,”
Proceedings of the General Discussion of Heat Transfer
,
Institute of Mechanical Engineers
,
London
, p.
180
.
17.
Migai
,
V. K.
, 1963, “
Effect of Non-uniform Heat Transfer Over the Height of a Fin on its Efficiency
,”
Inzh.-Fiz. Zh.
0021-0285,
6
(
3
), p.
51
.
18.
Thomas
,
D. G.
, and
Hayes
,
P. H.
, 1970, “
High Performance Heat Transfer Surfaces
,”
Ind. Eng. Chem.
0019-7866,
62
(
2
), p.
4
.
19.
Han
,
L. S.
, and
Lefkowitz
,
S. G.
, 1960, “
Constant Cross Section Fin Efficiencies for Non-uniform Surface Heat Transfer Coefficients
,” ASME Paper 60-WA-41,
American Society of Mechanical Engineers
, New York.
20.
Unal
,
H. C.
, 1985, “
Determination of the Temperature Distribution in an Extended Surface with a Non Uniform Heat Transfer Coefficient
,”
Int. J. Heat Mass Transfer
0017-9310,
28
(
12
), p.
2279
.
21.
Clarke
,
D. D.
,
Vasquez
,
V. R.
,
Whiting
,
W. B.
,
Greiner
,
M.
, 2001, “
Sensitivity and Uncertainty Analysis of Heat Exchanger Designs to Physical Properties Estimation
,”
Soryushiron Kenkyu
0371-1838
21
pp.
993
1017
.
22.
Saboya
,
F. E. M.
, and
Sparrow
,
E. M.
, 1974, “
Local and Average Heat Transfer Coefficients for One-Row Plate Fin and Tube Heat Exchanger Configurations
,”
ASME J. Heat Transfer
0022-1481,
96
, p.
265
.