Abstract

The objective of this study is the thermal investigation of a typical spark-ignition (SI) engine combustion chamber with particular focus in determination of the locations where the heat flux and heat transfer coefficient are highest. This subject is an important key for some design purposes especially thermal loading of the piston and cylinder head. To this end, CFD simulation using the KIVA-3V CFD code on a PC platform for flow, combustion, and heat transfer in a typical SI engine has been performed. Some results including the temporal variation of the area-averaged heat flux and heat transfer coefficient on the piston, combustion chamber, and cylinder wall are presented. Moreover, the temporal variation of the local heat transfer coefficient and heat flux along a centerline on the piston as well as a few locations on the combustion chamber wall are shown. The investigation reveals that during the combustion period, the heat flux and heat transfer coefficient vary substantially in space and time due to the transient nature of the flame propagation. For example, during the early stages of the flame impingement on the wall, the heat flux undergoes a rapid increase by as much as around 10 times the preimpingement level. In other words, the initial rise of the heat flux at any location is related to the time of the flame arrival at that location.

1.
Heywood
,
J. B.
, 1987,
Internal Combustion Engine Fundamentals
,
McGraw-Hill
,
New York
.
2.
Eichelberg
,
G.
, 1939, “
Some New Investigations on Old Combustion Engine Problems
,”
Engineering (London)
0013-7782,
148
, pp.
463
547
.
3.
Annand
,
W. J. D.
, 1963, “
Heat Transfer in the Cylinders of Reciprocating Internal Combustion Engines
,”
Proc. Inst. Mech. Eng.
0020-3483,
177
(
36
), pp.
973
990
.
4.
Woschni
,
G.
, 1967, “
A Universally Applicable Equation for the Instantaneous Heat Transfer Coefficient in the Internal Combustion Engine
,”
SAE Trans.
0096-736X,
76
, pp.
3065
3083
.
5.
LeFeuvre
,
T.
,
Myers
,
P. S.
, and
Uyehara
,
O. A.
, 1969, “
Experimental Instantaneous Heat Fluxes in a Diesel Engine and Their Correlation
,” SAE Paper No. 690464.
6.
Whitehouse
,
N. D.
, 1970–1971, “
Heat Transfer in a Quiescent Chamber Diesel Engine
,”
Proc. Inst. Mech. Eng.
0020-3483,
185
, pp.
963
975
.
7.
Flynn
,
P.
,
Mizusawa
,
M.
,
Uyehara
,
O. A.
, and
Myers
,
P. S.
, 1972, “
An Experimental Determination of the Instantaneous Potential Radiant Heat Transfer Within an Operating Diesel Engine
,” SAE Paper No. 720022.
8.
Dent
,
J. C.
, and
Suliaman
,
S. L.
, 1977, “
Convective and Radiative Heat Transfer in a High Swirl Direct Injection Diesel Engine
,” SAE Paper No. 770407.
9.
Overbye
,
V. D.
,
Bennethum
,
J. E.
,
Uyehara
,
O. A.
, and
Myers
,
P. S.
, 1961, “
Unsteady Heat Transfer in Engines
,”
SAE Trans.
0096-736X,
69
, pp.
461
494
.
10.
Oguri
,
T.
, 1960, “
On the Coefficient of Heat Transfer Between Gases and Cylinder Walls of the Spark-Ignition Engine
,”
Bull. JSME
0021-3764,
3
(
11
), pp.
363
374
.
11.
Elser
,
K.
, 1954, “
Der Instationare Warmeubergang in Dieselmotoren
,” Mitt Inst. Thermodyn., Zurich, No. 15.
12.
Alkidas
,
A. C.
, 1980, “
Heat Transfer Characteristics of a Spark-Ignition Engine
,”
ASME J. Heat Transfer
0022-1481,
102
(
2
), pp.
189
193
.
13.
Alkidas
,
A. C.
, and
Myers
,
J. P.
, 1982, “
Transient Heat-Flux Measurements in the Combustion Chamber of a Spark-Ignition Engine
,”
ASME J. Heat Transfer
0022-1481,
104
, pp.
62
67
.
14.
Jennings
,
M. J.
, and
Morel
T.
, 1990, “
An Improved Near Wall Heat Transfer Model for Multidimensional Engine Flow Calculations
,” SAE Paper No. 900251.
15.
Popp
,
P.
, and
Baum
,
M.
, 1995, “
Heat Transfer and Pollutant Formation Mechanisms in Insulated Combustion Chambers
,” SAE Paper No. 952387.
16.
Kleemann
,
A. P.
,
Gosman
,
A. D.
, and
Binder
,
K. B.
, 2001, “
Heat Transfer in Diesel Engines: A CFD Evaluation Study
,”
The 5th International COMODIA Symposium on Diagnostics and Modeling of Combustion in Internal Combustion Engines
.
17.
Amsden
,
A. A.
,
O’Rourke
,
P. J.
, and
Butler
,
T. D.
, 1989, “
Kiva-II: A Computer Program for Chemically Reactive Flows With Sprays
,” L. A. Report No. 111560-MS.
18.
Amsden
,
A. A.
,
Ramshaw
,
J. D.
,
O’Rourke
,
P. J.
, and
Dukowicz
,
J. K.
, “
KIVA: A Computer Program for Two- and Three-Dimensional Fluid Flows With Chemical Reactions and Fuel Sprays
,” Los Alamos National Laboratory Report No. LA-10245-MS.
19.
Amsden
,
A. A.
,
Butler
,
T. D.
,
O’Rourke
,
P. J.
, and
Ramshaw
,
J. D.
, 1985, “
KIVA: A Comprehensive Model for 2D and 3D Engine Simulations
,” SAE Paper No. 850554.
20.
Spalding
,
D. B.
, 1976, “
Development of the Eddy-Breakup Model of Turbulent Combustion
,” in
Proceedings of the 16th International Symposium on Combustion
,
Pittsburgh, PA
, pp.
1657
1663
.
21.
Gosman
,
A. D.
, 1985, “
Computer Modeling of Flow and Heat Transfer in Engines, Progress and Prospect
,” in
Proceedings of the COMODIA Symposium, JSME, SAE, and MESJ
, Tokyo, Japan.
22.
Diwakar
,
R.
, 1984, “
Assessment of the Ability of a Multidimensional Computer Code to Model Combustion in a Homogeneous Charge Engine
,” SAE Paper No. 840230.
23.
Das
,
S.
, and
Dent
,
J. C.
, 1995, “
Simulation of the Mean Flow in the Cylinder of a Motored 4-Valved Spark Ignition Engine
,” SAE Paper No. 952384.
You do not currently have access to this content.