This paper presents the results of an experimental study of forced convection heat transfer in a narrow rectangular duct fitted with a circular tube and/or a delta-winglet pair. The duct was designed to simulate a single passage in a fin-tube heat exchanger. Heat transfer measurements were obtained using a transient technique in which a heated airflow is suddenly introduced to the test section. High-resolution local fin-surface temperature distributions were obtained at several times after initiation of the transient using an imaging infrared camera. Corresponding local fin-surface heat transfer coefficient distributions were then calculated from a locally applied one-dimensional semi-infinite inverse heat conduction model. Heat transfer results were obtained over an airflow rate ranging from to These flow rates correspond to a duct-height Reynolds number range of 670–6300 with a duct height of 1.106 cm and a duct width-to-height ratio, of 11.25. The test cylinder was sized such that the diameter-to-duct height ratio, is 5. Results presented in this paper reveal visual and quantitative details of local fin-surface heat transfer distributions in the vicinity of a circular tube, a delta-winglet pair, and a combination of a circular tube and a delta-winglet pair. Comparisons of local and average heat transfer distributions for the circular tube with and without winglets are provided. Overall mean fin-surface Nusselt-number results indicate a significant level of heat transfer enhancement associated with the deployment of the winglets with the circular cylinder. At the lowest Reynolds numbers (which correspond to the laminar operating conditions of existing geothermal air-cooled condensers), the enhancement level is nearly a factor of 2. At higher Reynolds numbers, the enhancement level is close to 50%.
Skip Nav Destination
Article navigation
Research Papers
Heat Transfer Enhancement for Finned-Tube Heat Exchangers With Winglets
James E. O’Brien,
James E. O’Brien
Idaho National Engineering and Environmental Laboratory, Idaho Falls, ID 83415
Search for other works by this author on:
Manohar S. Sohal
Manohar S. Sohal
Idaho National Engineering and Environmental Laboratory, Idaho Falls, ID 83415
Search for other works by this author on:
James E. O’Brien
Idaho National Engineering and Environmental Laboratory, Idaho Falls, ID 83415
Manohar S. Sohal
Idaho National Engineering and Environmental Laboratory, Idaho Falls, ID 83415
Manuscript received November 7, 2003; revision received April 21, 2004. Review conducted by: P. M. Ligrani.
J. Heat Transfer. Feb 2005, 127(2): 171-178 (8 pages)
Published Online: March 15, 2005
Article history
Received:
November 7, 2003
Revised:
April 21, 2004
Online:
March 15, 2005
Citation
O’Brien , J. E., and Sohal, M. S. (March 15, 2005). "Heat Transfer Enhancement for Finned-Tube Heat Exchangers With Winglets." ASME. J. Heat Transfer. February 2005; 127(2): 171–178. https://doi.org/10.1115/1.1842786
Download citation file:
Get Email Alerts
Cited By
Entropic Analysis of the Maximum Output Power of Thermoradiative Cells
J. Heat Mass Transfer
Molecular Dynamics Simulations in Nanoscale Heat Transfer: A Mini Review
J. Heat Mass Transfer
Related Articles
Heat Transfer in Crossflow Over Cylinders Between Two Parallel Plates
J. Heat Transfer (August,1992)
Heat Transfer Around a Tube in In-Line Tube Banks Near a Plane Wall
J. Heat Transfer (November,1990)
Heat Transfer-Friction Characteristic Comparison in Rectangular Ducts With Slit and Solid Ribs Mounted on One Wall
J. Heat Transfer (August,1998)
Heat Transfer and Pressure Drop Characteristics of an Assembly of Partially Segmented Plates
J. Heat Transfer (February,1989)
Related Proceedings Papers
Related Chapters
Hydraulic Resistance
Heat Transfer & Hydraulic Resistance at Supercritical Pressures in Power Engineering Applications
Threshold Functions
Closed-Cycle Gas Turbines: Operating Experience and Future Potential
Heat Transfer Enhancement by Using Nanofluids in Laminar Forced Convection Flows Considering Variable Properties
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)