Abstract
Natural soils or coarse granular materials containing large particles such as rockfill or ballast are often an issue for geotechnical projects. However, since it is usually complicated or impossible to set up a big enough experimental apparatus to test these materials, their mechanical behavior remains poorly known. To circumvent this difficulty, we have developed a set of triaxial cells of various sizes to study the experimental behavior of granular soils containing particle sizes of up to 160 mm. This paper presents the first results of a two-part experimental study. The first part consists of triaxial tests on sand samples of different sizes in order to examine specimen scale effects. Pre-peak behavior is not affected by the specimen size, whereas post-peak behavior depends on the test conditions that control the development of strain localizations. In the second part, we present drained triaxial compression tests on large samples of calcareous rockfill materials that have parallel grain size distributions. The results show a nonstandard evolution of the friction angle in relationship to grain size if compared to similar studies on coarse granular materials. Although grain crushing occurs during compression, the strain-stress curves of the different materials with different grain sizes do remain close. We explain this phenomenon by the strength evolution of the individual grains with respect to their sizes.
Issue Section:
Research Papers
References
1.
ASTM D854-92,
1995
, “Standard Test Methods for Specific Gravity of Soil Solids by Water Pycnometer
,” Annual Book of ASTM Standards, Vol. 04.08
, ASTM International, West Conshohocken, PA, pp. 80
–83
.2.
ASTM D2487-93,
1995
, “Standard Test Method for Classification of Soils for Engineering Purposes
,” Annual Book of ASTM Standards, Vol. 04.08
, ASTM International, West Conshohocken, PA, pp. 207
–217
.3.
ASTM D2488-93,
1995
, “Standard Practice for Description and Identification of Soils (Visual-Manual Procedure)
,” Annual Book of ASTM Standards, Vol. 04.08
, ASTM International, West Conshohocken, PA, pp. 218
–228
.4.
ASTM D4253-93,
1995
, “Standard Test Method for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table
,” Annual Book of ASTM Standards, Vol. 04.08
, ASTM International, West Conshohocken, PA, pp. 533
–545
.5.
ASTM D4254-91,
1995
, “Standard Test Method for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density
,” Annual Book of ASTM Standards, Vol. 04.08
, ASTM International, West Conshohocken, PA, pp. 546
–553
.6.
Baldi
, G.
and Nova
, R.
, 1984
, “Membrane Penetration Effects in Triaxial Testing
,” J. Geotech. Engrg.
0733-9410, Vol. 110
, No. 3
, pp. 403
–420
. https://doi.org/10.1061/(ASCE)0733-9410(1984)110:3(403)7.
Barton
, N.
and Kjaernsli
, B.
, 1981
, “Shear Strength of Rockfill
,” J. Geotech. Engrg.
0733-9410, Vol. 107
, No. 7
, pp. 873
–891
.8.
Becker
, E.
, Chan
, C. K.
, and Bolton Seed
, H.
, 1972
, “Strength and Deformation Characteristics of Rockfill Materials in Plane Strain and Triaxial Compression Tests
,” Report No. TE 72-3, Department of Civil and Environmental Engineering, University of California, Berkeley, Berkeley, CA.9.
Bennazzouz
, I. K.
, 2005
, “Validation d’une grande cellule triaxiale—Essais sur sable de Loire [Validation of a large triaxial cell—Tests on Loire sand specimens]
,” M.S. thesis, Ecole Centrale Nantes
, Nantes, France (in French).10.
Biarez
, J.
and Hicher
, P. Y.
, 1997
, “Influence de la granulométrie et de son évolution par ruptures de grains sur le comportement mécanique de matériaux granulaires [Effect of the grain size distribution and its evolution due to grain crushing on the mechanical behaviour of granular materials]
,” Revue Francaise Genie Civil
1279-5119, Vol. 1
, No. 4
, pp. 607
–631
.11.
Bishop
, A. W.
, 1971
, “Shear Strength Parameters for Undistubed and Remoulded Soil Specimens
,” Stress-Strain Behaviours of Soils
, Cambridge University Press
, Cambridge, U.K.
, pp. 3
–58
.12.
Bishop
, A. W.
and Green
, G. E.
, 1965
, “The Influence of End Restraint on the Compression Strength of a Cohesionless Soil
,” Geotechnique
0016-8505, Vol. 15
, No. 3
, pp. 243
–266
. https://doi.org/10.1680/geot.1965.15.3.24313.
Charles
, J. A.
and Watts
, K. S.
, 1980
, “The Influence of Confining Pressure on the Shear Strength of Compacted Rockfill
,” Geotechnique
0016-8505, Vol. 30
, No. 4
, pp. 353
–367
. https://doi.org/10.1680/geot.1980.30.4.35314.
Chávez
, C.
, 2004
, “Estudio del comportamiento triaxial de materiales granulares de tamaño medio; con énfasis en la influencia de la succión [Study of the triaxial behaviour of granular materials of intermediate sizes, with emphasis to the influence of suction]
,” Ph.D. thesis, Universidad Politécnica de Cataluña
, Barcelona, Catalonia, Spain (in Spanish).15.
Chávez
, C.
and Alonso
, E. E.
, 2003
, “A Constitutive Model for Crushed Granular Aggregates Which Include Suction Effects
,” Soils Found.
0038-0806, Vol. 43
, No. 4
, pp. 215
–227
.16.
Dano
, C.
, Hareb
, H.
, and Hicher
, P.-Y.
, 2003
, “Characterization of Loire River Sand in the Small Strain Domain Using New Bender-Extender Elements
,” Proceedings 16th ASCE Engineering Mechanics Conference
, Seattle, WA, ASCE
, Reston, VA
(CD-ROM).17.
Daouadji
, A.
, Hicher
, P.-Y.
, and Rahma
, A.
, 2001
, “An Elastoplastic Model for Granular Materials Taking into Account Grain Breakage
,” Eur. J. Mech. A/Solids
0997-7538, Vol. 20
, pp. 113
–137
. https://doi.org/10.1016/S0997-7538(00)01130-X18.
Darve
, F.
, Hicher
, P.-Y.
, and Reynouard
, J.-M.
, 1995
, “Les géomatériaux: theories, experiences et modèles [Geomaterials: Theory, Experiment and Modelling
,” Etudes en mécanique des matériaux et des structures [Studies in Mechanics of Materials and Structures]
, Hermès
, Paris, France
.19.
De La Hoz
, K.
, 2007
, “Estimacion de los parametros de resistencia al corte en suelos granulares gruesos [Assessment of shear strength properties of coarse granular soils]
,” Magister thesis, University of Chile (Santiago), Chile (in Spanish).
20.
El Bied
, A.
, 2000
, “Etude expérimentale et modélisation du comportement des roches granulaires: écrouissage, radoucissement et rupture en mode localize [Experimental Study and Modeling of the Behavior of Granular Rocks: Hardening, Softening and Failure in a Localized Mode]
,” Ph.D. thesis, l’Ecole Nationale des Ponts et Chaussées
, Paris, France (in French).21.
Frossard
, E.
, 1979
, “Effect of Sand Grain Shape on Interparticle Friction: Indirect Measurements by Rowe’s Stress-Dilatancy Theory
,” Geotechnique
0016-8505, Vol. 29
, No. 3
, pp. 341
–350
. https://doi.org/10.1680/geot.1979.29.3.34122.
Frossard
, E.
, Hu
, W.
, Dano
, C.
, and Hicher
, P.-Y.
, 2010
, “Evaluation of Rockfill Shear Strength Including Size Effect Within Granular Materials
,” Geotechnique
0016-8505 (unpublished).23.
Frydman
, S.
, Zeitlen
, J. G.
, and Alpan
, I.
, 1973
, “The Membrane Effect in Triaxial Testing of Granular Soils
,” J. Test. Eval.
0090-3973, Vol. 1
, No. 1
, pp. 37
–41
. https://doi.org/10.1520/JTE11599J24.
Georgopoulos
, I. O.
and Vardoulakis
, I.
, 2005
, “Corrections on the Specimen Volume Changes and Axial Force in the Wykeham Farrance Triaxial Cell
,” Internal Report, NTU, Athens, Greece.25.
Guimaraes
, M. S.
, Valdes
, J. R.
, Palomino
, A. M.
, and Santamarina
, J. C.
, 2007
, “Aggregate Production: Fines Generation During Rock Crushing
,” Int. J. Min. Process.
0301-7516, Vol. 81
, No. 4
, pp. 237
–247
. https://doi.org/10.1016/j.minpro.2006.08.00426.
Habib
, P.
, 1972
, “Effet d’Echelle sur les Sables Denses [Scale Effect in Dense Sands]
,” Séminaire Plasticité et Viscoplasticité [Plasticity and Viscoplasticity Workshop]
, Ecole Polytechnique Palaiseau, France
.27.
Hardin
, B. O.
, 1985
, “Crushing of Soil Particles
,” J. Geotech. Engrg.
0733-9410, Vol. 111
, No. 10
, pp. 1177
–1192
. https://doi.org/10.1061/(ASCE)0733-9410(1985)111:10(1177)28.
Holtz
, W.G.
and Gibbs
, H.J.
, 1956
, “Triaxial Shear Tests On Pervious Gravelly Soils
,” J. Soil Mech. and Found. Div.
0044-7994, Vol. 82
, No. SMI
, pp. 1
–22
.29.
Indraratna
, B.
, Ionescu
, D.
, and Christie
, H. D.
, 1998
, “Shear Behaviours of Railway Ballast Based on Large-Scale Triaxial Tests
,” J. Geotech. Geoenviron. Eng.
1090-0241, Vol. 124
, No. 5
, pp. 439
–449
. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:5(439)30.
Indraratna
, B.
, Wijewardena
, L. S. S.
, and Balasubramaniam
, A. S.
, 1993
, “Large-Scale Triaxial Testing of Grey Wacke Rockfill
,” Geotechnique
0016-8505, Vol. 43
, No. 1
, pp. 37
–51
. https://doi.org/10.1680/geot.1993.43.1.3731.
Lackenby
, J.
, Indraratna
, B.
, McDowell
, G.
, and Christie
, D.
, 2007
, “Effect of Confining Pressure on Ballast Degradation and Deformation Under Cyclic Triaxial Loading
,” Geotechnique
0016-8505, Vol. 57
, No. 6
, pp. 527
–536
. https://doi.org/10.1680/geot.2007.57.6.52732.
Lam
, W.-K.
and Tatsuoka
, F.
, 1988
, “Triaxial Compressive and Extension Strength of Sand Affected by Strength Anisotropy and Sample Slenderness
,” ASTM Spec. Tech. Publ.
0066-0558, Vol. 977
, pp. 655
–666
.33.
Leps
, T. M.
, 1970
, “Review of Shearing Strength of Rockfill
,” J. Soil Mech. and Found. Div.
0044-7994, Vol. 96
, No. 4
, pp. 1159
–1170
.34.
Lowe
, J.
, 1964
, “Shear Strength of Coarse Embankment Dam Materials
,” Proceedings of the Eighth Congress on Large Dams
, Edinburgh
, Transactions, Vol. III, pp. 745
–761
.35.
Marachi
, N. D.
, Chan
, C. K.
, and Seed
, H. B.
, 1972
, “Valuation of Properties of Rockfill Materials
,” J. Soil Mech. and Found. Div.
0044-7994, Vol. 98
, No. SMI
, pp. 95
–114
.36.
Marachi
, N. D.
, Chan
, C. K.
, Seed
, H. B.
, and Duncan
, J. M.
, 1969
, “Strength and Deformation Characteristics of Rockfill Materials
,” Report No. TE-69-5, Dept. of Civil Engineering, Univ. of California, Berkeley
, Berkeley, CA.37.
Marsal
, R. J.
, 1967
, “Large-Scale Testing of Rockfill Materials
,” J. Soil Mech. and Found. Div.
0044-7994, Vol. 93
, No. SM2
, pp. 27
–44
.38.
Marsal
, R. J.
, Arellano
, L. R.
, and Nunez
, A. G.
, 1967
, “Plane Strain Testing of Rockfill Materials
,” Proceedings of the Third Panamerican Conference on Soil Mechanics and Foundation Engineering
, Caracas, Venezuela, Vol. 1
, pp. 249
–271
.39.
Marsal
, R. J.
, Moreno Gomez
, E.
, Nunez
, A.
, Cuellar
, R.
, and Moreno Ramos
, R.
, 1965
, “Research on the Behaviour of Granular Materials and Rockfill Samples
,” Internal Report, Comision Federal de Electricidad, Mexico.40.
Muir Wood
, D.
and Maeda
, K.
, 2008
, “Changing Grading of Soil: Effect on Critical State
,” Acta Geotech.
Vol. 3
, No. 1
, pp. 3
–14
. https://doi.org/10.1007/s11440-007-0041-041.
NF P 94-074 10/94, “
Sols: Reconnaissance et Essais—Essai à l’appareil triaxial de révolution—Appareillage—Préparation des éprouvettes—Essais (UU) non consolidé non drainé—Essai (CU+u) consolidé non drainé avec mesure de pression interstitielle—Essai (CD) consolidé drainé [Soil Testing: Axi-Symmetric Triaxial Test—Setup—Test Preparation—UU Test—CU+u Test—CD Test
,” AFNOR, France.42.
Nicholson
, P. G.
, Seed
, R. B.
, and Anwar
, H.
, 1989
, Measurement and Elimination of Membrane Compliance Effects in Undrained Triaxial Testing
,” Report No. UCB/EERC-89/10, Earthquake Engineering Research Center, University of California (Berkeley), Berkeley, CA.43.
Ramana
, K. V.
and Raju
, V. S.
, 1982
, “Membrane Penetration in Triaxial Tests
,” J. Geotech. Engrg. Div.
0093-6405, Vol. 108
, No. GT2
, pp. 305
–310
.44.
Richefeu
, V.
, El Youssoufi
, M. S.
, Azema
, E.
, and Radjai
, F.
, 2009
, “Force Transmission in Dry and Wet Granular Media
,” Powder Technol.
0032-5910, Vol. 190
, pp. 258
–263
. https://doi.org/10.1016/j.powtec.2008.04.06945.
Varadarajan
, A.
, Sharma
, K. G.
, Abbas
, S. M.
, and Dhawan
, A. K.
, 2006
, “The Role of Nature of Particles on the Behaviour of Rockfill Materials
,” Soils Found.
0038-0806, Vol. 46
, No. 5
, pp. 569
–584
. https://doi.org/10.3208/sandf.46.56946.
Verdugo
, R.
and de la Hoz
, K.
, 2006
, “Strength and Stiffness of Coarse Granular Soils
,” Geotechnical Symposium “Soil Stress-Strain Behaviour: Measurement, Modelling and Analysis
, Rome, March 16–17, Ling
H. I.
, Callisto
L.
, Leshchinsky
D.
, and Koseki
J.
, Eds., Springer
, Dordrecht, The Netherlands
, pp. 243
–252
.
This content is only available via PDF.
All rights reserved. This material may not be reproduced or copied, in whole or in part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of ASTM International.
You do not currently have access to this content.
