Abstract
A technique to predict the stress-strain behavior of clays along various stress paths is presented. The experimental results of stress-controlled triaxial pure shear and consolidation tests conducted on normally consolidated and lightly overconsolidated samples are given, and a method to evaluate the parameters required for prediction by the proposed technique is discussed. Comparison between experimental and predicted stress-strain behavior of normally consolidated and lightly overconsolidated samples along stress paths shows that the technique predicts the behavior quite well.
Issue Section:
Research Papers
References
1.
Roscoe
, K. H.
, “The Influence of Strains in Soil Mechanics
,” Geotechnique
0016-8505, Vol. 20
, No. 20
, 1970
, pp. 129
-170
.2.
Schofield
, A. N.
and Wroth
, C. P.
, Critical State Soil Mechanics
, McGraw-Hill Book Co. Ltd.
, London
, 1968
.3.
Roscoe
, K. H.
and Burland
, J. B.
, “On the generalized Stress-Strain Behavior of Wet Clay
,” Symposium on Engineering Plasticity
, Cambridge University Press
, London
, 1968
, pp. 535
-609
.4.
Newland
, P. L.
, “An Experimental Study of the Stress-Strain Characteristics of a ‘Wet’ Clay and Their Relevance to Settlement Analysis
,” Technical Report 15, Division of Applied Geomechanics, Common-wealth Scientific and Industrial Research Organization
, Australia, 1973
.5.
Yudhbir
, Mathur
, S. K.
, and Kugunathan
, V.
, “Critical State Parameters
,” American Society of Civil Engineers, Journal of the Geotechnical Engineering Division
, Vol. 104
, No. GT4
, 1978
, pp. 497
-501
.6.
Wood
, D. M.
, “Exploration of Principal Stress Space with Kaolin in a True Triaxial Apparatus
,” Geotechnique
0016-8505, Vol. 25
, No. 4
, 1975
, pp. 283
-297
.7.
Lewin
, P. I.
, “Three-Dimensional Anisotropic Consolidation of Clay and the Relationship Between Plane Strain and Triaxial Test Data
,” presented at the RILEM Symposium on Deformation and Rupture of Solids Subjected to Multiaxial Stresses
, International Union of Testing and Research Laboratories for Materials and Structures
, Cannes
, 1971
.8.
Mathur
, S. K.
, “Stress-Strain-Time Behaviour of Anisotropically Consolidated Marine Clay Under Various Stress Paths
,” Ph.D. thesis, Department of Civil Engineering, IIT
, Kanpur, India.9.
Parry
, R. H. G
, “Strength and Deformation of Clay
,” Ph.D. thesis, University of London
, 1956
.10.
Burland
, J. B.
, “Deformation of Soft Clay
,” Ph.D. thesis, Cambridge University
, London, 1967
.11.
Yudhbir
, and Mathur
, S. K.
, “Prediction of Stress-Deformation Characteristics of Anisotropically Consolidated Clay
,” presented at the International Conference on Evaluation and Prediction of Subsidence
, sponsored by Engineering Foundation
, U.S.A.
and cosponsored by American Society of Civil Engineers
, Florida
, 1978
.12.
Scott
, R. F.
and Ko
, H. Y.
, “Stress-Deformation and Strength Characteristics
,” State of the Art Report, Proceedings of the Seventh International Conference on Soil Mechanics and Foundation Engineers
, Mexico
, 1969
, pp. 1
-47
.13.
Bishop
, A. W.
and Henkel
, D. J.
, The Measurement of Soil Properties in the Triaxial Test
, Edward Arnold (Publishers) Ltd.
, London
, 1962
.14.
Berre
, T.
and Bjerrum
, L.
, “Shear Strength of Normally Consolidated Clays
,” Proceedings of the Eighth International Conference on Soil Mechanics and Foundation Engineering
, Moscow
, pp. 39
-49
.15.
Parry
, R. H. G.
and Nadarajah
, V.
, “Observation on Laboratory Prepared, Lightly Overconsolidated Specimens of Kaolin
,” Geotechnique
0016-8505, Vol. 24
, No. 3
, 1974
, pp. 345
-358
.16.
Wroth
, C. P.
, “Some Features of the Mechanical Behaviour of Soils
,” Technical Report, Cornell University
, Ithaca, N.Y., 06
1968
.17.
Yudhbir
and Mathur
, S. K.
, “Path Dependent Drained Creep of Clays
,” Proceedings of the Ninth International Conference on Soil Mechanics and Foundation Engineering
, Vol. 1
, 1977
, pp. 353
-356
.18.
Mathur
, S. K.
and Yudhbir
, “Method of Calculating Long-Term Creep Settlements
,” American Society of Civil Engineers, Journal of the Geotechnical Engineering Division
0093-6405, Vol. 8
, No. GT7
, 1977
, pp. 824
-826
.
This content is only available via PDF.
All rights reserved. This material may not be reproduced or copied, in whole or in part, in any printed, mechanical, electronic, film, or other distribution and storage media, without the written consent of ASTM International.
You do not currently have access to this content.