Oil-free microturbomachinery (OFT) implements compliant foil bearings because of their minute drag and ability to operate in extreme (high or low) temperature. Prominent to date, bump-foil thrust bearings integrate an underspring thin metal structure that provides resilience and material damping, and while the rotor is airborne, it acts in series with the stiffness and damping of the gas film. The design and manufacturing of foil bearings remain costly as it demands extensive engineering and actual experience. Alternative foil bearing configurations, less costly and easier to manufacture, are highly desirable to enable widespread usage of OFT. This paper details the design and manufacturing of a novel Rayleigh-step metal mesh foil thrust bearing (MMFTB) as well as its testing on a dedicated rig. Metal mesh structures offer significant material structural damping and can be easily procured at a fraction of the cost of a typical bump-foil strip layer. The MMFTB consists of a solid carrier, a number of stacked annular copper mesh sheets (wire diameter = 0.25, 0.3, and 0.41 mm), and a steel top foil (0.127 mm thick) that makes six pads (ID = 50.8 mm, OD =2 ID), each 45 deg in extent. A 3 μm polymer coats each pad, and a photochemical process etches a step 20 μm in height. Static and dynamic load measurements (without rotor speed) demonstrate that the MMFTB has structural stiffness and material damping similar to that of a publicized bump-type foil thrust bearing. A maiden test of the MMFTB with rotor speed of Ω = 15 krpm (∼80 m/s at bearing outer diameter (OD)) proved briefly the bearing operation when applying a tiny thrust load. Further tests with ambient air, a rotor speed of 40 krpm (∼212 m/s at bearing OD), and a very light load/area <7 kPa failed several of the prototype bearings, all exhibiting significant wear on one or more pads. The source of the failure is the inherent unevenness of the metal mesh stacked substructures, thus causing the pads to bulge toward the rotor collar surface before a load applies. A deficient anchoring method exacerbates the unevenness. Incidentally, a high rotor speed induced large windage that lifted the top foils pushing them against the spinning collar. As the bearing moved toward the rotating collar to begin applying thrust, the local high spots rubbed against the collar before a hydrodynamic wedge could form to separate the surfaces. Without a robust sacrificial coating, metal-to-metal contact quickly disfigured the contacting top foil pads, erasing the etched step, and leading to failure. In concept, and on paper, the mesh sheets and the top foil lay flat against the bearing carrier, giving a false sense of uniformity in the design process. In actuality, a designer must consider the manufactured states of the individual components and how they assemble. A redesign of the bearing intends to overcome the existing flaws (highlighted herein) by incorporating a thicker top foil that is well anchored (to better withstand the effects of windage), a robust sacrificial coating, and a hydrodynamic wedge accomplished via a circumferential taper on each pad.

References

References
1.
Agrawal
,
G. L.
,
1997
, “
Foil Air/Gas Bearing Technology—An Overview
,”
ASME
Paper No. 97-GT-347.
2.
Heshmat
,
H.
,
Walowit
,
J. A.
, and
Pinkus
,
O.
,
1983
, “
Analysis of Gas Lubricated Compliant Thrust Bearings
,”
ASME J. Tribol.
,
105
(
4
), pp.
638
646
.
3.
Heshmat
,
H.
,
1993
, “
Analysis of Compliant Foil Bearings With Spatially Variable Stiffness
,”
AIAA
Paper No. AIAA-91-2102-CP.
4.
Heshmat
,
C. A.
,
Xu
,
D. S.
, and
Heshmat
,
H.
,
2000
, “
Analysis of Gas Lubricated Foil Thrust Bearings Using Coupled Finite Element and Finite Difference Methods
,”
ASME J. Tribol.
,
122
(
1
), pp.
199
204
.
5.
Hryniewicz
,
P.
,
Locke
,
D. H.
, and
Heshmat
,
H.
,
2003
, “
New-Generation Development Rigs for Testing High-Speed Air-Lubricated Thrust Bearings
,”
Tribol. Trans.
,
46
(
4
), pp.
556
559
.
6.
Iordanoff
,
I.
,
1998
, “
Maximum Load Capacity Profiles for Gas Thrust Bearings Working Under High Compressibility Number Conditions
,”
ASME J. Tribol.
,
120
(
3
), pp.
571
576
.
7.
Iordanoff
,
I.
,
1999
, “
Analysis of an Aerodynamic Compliant Foil Thrust Bearing: Method for a Rapid Design
,”
ASME J. Tribol.
,
121
(
4
), pp.
816
821
.
8.
Gu
,
A. L.
, and
Nadjafi
,
R. H.
,
1993
, “
Foil Thrust Bearing With Varying Radial and Circumferential Stiffness
,” Honeywell International Inc., Morris Plains, NJ. U.S. Patent No.
5248205A
.https://patents.google.com/patent/US5248205
9.
Heshmat
,
H.
,
1999
, “
High Load Capacity Compliant Foil Hydrodynamic Thrust Bearing
,” Mohawk Innovative Tech Inc., Albany, NY, U.S. Patent No.
5961217A
.https://patents.google.com/patent/US5961217
10.
Bruckner
,
R. J.
,
2004
, “
Simulation and Modeling of the Hydrodynamic, Thermal and Structural Behavior of Foil Thrust Bearings
,”
Ph.D. dissertation
, Case Western Reserve University, Cleveland, OH.https://etd.ohiolink.edu/!etd.send_file?accession=case1089304186&disposition=inline
11.
Dykas
,
B.
,
2006
, “
Factors Influencing the Performance of Foil Gas Thrust Bearings for Oil Free Turbomachinery Applications
,”
Ph.D. dissertation
, Case Western Reserve University, Cleveland, OH.https://etd.ohiolink.edu/!etd.send_file?accession=case1144261305&disposition=inline
12.
Dykas
,
B.
,
Bruckner
,
R.
,
DellaCorte
,
C.
,
Edmonds
,
B.
, and
Prahl
,
J.
,
2009
, “
Design, Fabrication, and Performance of Foil Gas Thrust Bearings for Microturbomachinery Applications
,”
ASME J. Eng. Gas Turbines Power
,
131
(
1
), p.
012301
.
13.
Dickman
,
J. R.
,
2010
, “
An Investigation of Gas Foil Thrust Bearing Performance and Its Influencing Factors
,”
M.S. thesis
, Case Western Reserve University, Cleveland,
OH
.https://etd.ohiolink.edu/!etd.send_file?accession=case1270153301&disposition=inline
14.
Stahl
,
B. J.
,
2012
, “
Thermal Stability and Performance of Foil Thrust Bearings
,”
M.S. thesis
, Case Western Reserve University, Cleveland, OH.https://etd.ohiolink.edu/rws_etd/document/get/case1333722754/inline
15.
Feng
,
K.
,
Liu
,
L. J.
,
Guo
,
Z. Y.
, and
Zhao
,
X. Y.
,
2015
, “
Parametric Study on Static and Dynamic Characteristics of Bump-Type Gas Foil Thrust Bearing for Oil-Free Turbomachinery
,”
Proc. Inst. Mech. Eng., Part J
,
229
(
10
), pp.
1247
1263
.
16.
Lee
,
D.
, and
Kim
,
D.
,
2011
, “
Three-Dimensional Thermohydrodynamic Analyses of Rayleigh Step Air Foil Thrust Bearing With Radially Arranged Bump Foils
,”
Tribol. Trans.
,
54
(
3
), pp.
432
448
.
17.
Balducchi
,
F.
,
Arghir
,
M.
,
Gauthier
,
R.
, and
Renard
,
E.
,
2013
, “
Experimental Analysis of the Start-Up Torque of a Mildly Loaded Foil Thrust Bearing
,”
ASME J. Tribol.
,
135
(
3
), pp.
1
7
.
18.
Balducchi
,
F.
,
Arghir
,
M.
, and
Gauthier
,
R.
,
2015
, “
Experimental Analysis of the Dynamic Characteristics of a Foil Thrust Bearing
,”
ASME
Paper No. GT2014-25550.
19.
Somaya
,
K.
,
Yoshimoto
,
S.
, and
Miyatake
,
M.
,
2009
, “
Load Capacity of Aerodynamic Foil Thrust Bearings Supported by Viscoelastic Material
,”
Proc. Inst. Mech. Eng., Part J
,
223
(
4
), pp.
645
652
.
20.
Zheng
,
Y.
,
Lai
,
T.
,
Chen
,
S.
,
Chen
,
L.
,
Liu
,
L.
, and
Hou
,
Y.
,
2016
, “
Static Characteristics of Six Pads Multilayer Protuberant Foil Thrust Bearings
,”
Proc. Inst. Mech. Eng., Part J
,
231
(
2
), pp.
158
164
.
21.
Lai
,
T.
,
Wang
,
W.
,
Chen
,
S.
, and
Hou
,
Y.
,
2017
, “
Elastro-Hydrodynamic Lubrication Model of Multi-Decked Foil Thrust Bearing With Copper Wire Support
,”
J. Mater. Sci. Technol.
,
31
(
9
), pp.
4371
4379
.
22.
Alkhateeb
,
E. M.
,
2002
, “
Design, Modeling and Experimental Investigation of Mesh Vibration Dampers
,” Ph.D. dissertation, Department of Mechanical Engineering, Texas A&M University, College Station, TX.
23.
Chirathadam
,
T. A.
, and
San Andrés
,
L.
,
2012
, “
A Metal Mesh Foil Bearing and a Bump Type Foil Bearing: Comparison of Performance for Two Similar Size Gas Bearings
,”
ASME J. Eng. Gas Turbines Power
,
134
(
10
), p.
102501
.
24.
Beckwith
,
T. G.
,
Marangoni
,
R. D.
, and
Lienhard
,
V. J. H.
,
2007
,
Mechanical Measurements
,
6th Ed.
,
Pearson Education
,
Upper Saddle River, NJ
, Chap. 3.
You do not currently have access to this content.