Multiple-stage integrally geared compressors (IGCs) offer improved thermal efficiency and easier access for maintenance and overhaul than single-shaft centrifugal compressors. In an IGC, a main bull shaft drives pinion shafts, each having an impeller at its ends. The compression of process gas in the compressor stages induces axial loads along the pinion shafts that are transmitted via thrust collars (TCs) to the main bull gear (BG) shaft and balanced by a single thrust bearing. Manufacturing inaccuracies and a poor assembly process can lead to static angular misalignments of the TC and BG surfaces that affect the operating film thickness as well as the force and reaction moments of the lubricated mechanical element. In a follow-up to San Andrés et al. (2015, “On the Predicted Performance of Oil Lubricated Thrust Collars in Integrally Geared Compressors,” ASME J. Eng. Gas Turbines Power, 137(5), pp. 1–9), this paper presents an investigation of the performance of a single thrust collar configuration operating with increasing static angular misalignment of either the TC or BG. The flow model solves the Reynolds equation of hydrodynamic lubrication coupled to a thermal energy transport equation to determine the film pressure and bulk temperature fields, respectively. The model predicts performance parameters such as power loss and lubricant flow rate, and force and moment stiffness and damping coefficients. Predictions show that misaligning of either the thrust collar or bull gear alters the load-carrying area in the lubricated zone, shifts the pressure field with peak magnitudes doubling or more depending on the degree and direction of TC or BG misalignment. Static angular misalignment does not significantly affect the power loss, temperature rise, etc., but does have an effect on the dynamic coefficients (both axial and angular). Finally, a reduced complex dynamic stiffness matrix for the lubricated TC shows that some cross-coupled stiffness and moment coefficients are nonzero, indicating hydrodynamic coupling between axial and angular motions for the pinion and bull gear shafts. The coupling could affect the placement of the system natural frequencies and associated mode shapes as well as the system stability.

References

References
1.
San Andrés
,
L.
,
Cable
,
T. A.
,
Wygant
,
K.
, and
Morton
,
A.
,
2015
, “
On the Predicted Performance of Oil Lubricated Thrust Collars in Integrally Geared Compressors
,”
ASME J. Eng. Gas Turbines Power
,
137
(
5
), p.
052502
.
2.
Cable
,
T. A.
,
2015
, “
Analysis of Oil Lubricated Thrust Collars for Application in Integrally Geared Compressors
,” Masters thesis, Department of Mechanical Engineering,
Texas A&M University
, College Station, TX.
3.
Beaty
,
P. J.
,
Eisele
,
K.
,
Maceyka
,
T. D.
, and
Schwartz
,
C.
,
2000
, “
Integrally Geared API 617 Process Gas Compressors
,”
29th Turbomachinery Symposium
, Houston, TX, Sept. 18–22, pp.
239
246
.
4.
Wygant
,
K.
,
Bygrave
,
J.
,
Bosen
,
W.
, and
Pelton
,
R.
,
2016
, “
Application and Design of Integrally Geared Compressors
,”
Asia Turbomachinery and Pump Symposium
(
ATPS
), Singapore, Feb. 22–25.
5.
Simon
,
V.
,
1984
, “
Thermal Elastohydrodynamic Lubrication of Rider Rings
,”
ASME J. Tribol.
,
106
(
4
), pp.
492
498
.
6.
de Ling
,
F. B.
,
Evans
,
H. P.
, and
Snidle
,
R. W.
,
1996
, “
Thrust Cone Lubrication Part 1: Elastohydrodynamic Analysis of Conical Rims
,”
Proc. Inst. Mech. Eng., Part J
,
210
(
2
), pp.
85
96
.
7.
Heshmat
,
H.
, and
Pinkus
,
O.
,
1987
, “
Misalignment in Thrust Bearings Including Thermal and Cavitation
,”
ASME J. Tribol.
,
109
(
1
), pp.
108
114
.
8.
San Andrés
,
L.
,
2002
, “
Effects of Misalignment on Turbulent Flow Hybrid Thrust Bearings
,”
ASME J. Tribol.
,
124
(
1
), pp.
212
219
.
9.
Mittwollen
,
N.
,
Hegel
,
T.
, and
Glienicke
,
J.
,
1991
, “
Effect of Hydrodynamic Thrust Bearings on Lateral Shaft Vibrations
,”
ASME J. Tribol.
,
113
(
4
), pp.
811
817
.
10.
ASTM
,
2009
, “
Standard Practice for Viscosity-Temperature Charts for Liquid Petroleum Products
,”
ASTM International
, West Conshohocken, PA, Standard No. D341.
11.
Pinkus
,
O.
,
1990
,
Thermal Aspects of Fluid Film Tribology
,
ASME Press
,
New York
, pp.
80
85
.
12.
San Andrés
,
L.
,
2010
, “
Thermal Analysis of Finite Length Journal Bearings Including Fluid Inertia
,” Modern Lubrication Theory, Notes 7, Texas A&M University Libraries, College Station, TX, accessed Oct. 7, 2013, http://oaktrust.library.tamu.edu/handle/1969.1/93197
13.
Inprocera
,
F. P.
,
Dewitt
,
S. P.
,
Bergman
,
T. L.
, and
Lavine
,
A. S.
,
2007
,
Fundamentals of Heat and Mass Transfer
,
6th ed.
,
Wiley
,
Hoboken, NJ
.
You do not currently have access to this content.